Advertisement
Available languages
Available languages
Inserting/replacing battery (remote control)
• The button cell battery is already inserted into the IR remote control on delivery. Before first
use, remove the transparent plastic protective strip from the remote control. The protective
strip prevents battery discharge.
• Replace the battery when the remote control's range decreases or when the product no
longer responds to IR remote control commands. Proceed as follows to insert a battery:
- Push the battery holder locking lever to the right and simultaneously pull the battery holder
out of the IR remote control completely.
- Insert a new button cell battery, type CR2025, into the battery holder. The positive pole
must face up (see "+" imprint on the battery).
- Replace the battery holder into the IR remote control and make sure that the locking lever
clicks into place.
Installation
a) Feet
• Insert the 3 feet into the bottom end cap.
• Place the product on a flat, even surface.
• Make sure the product cannot tilt over.
b) Wall mount
• Mark the 2 drill holes on the installation surface.
The maximum permissible distance between the drill holes is 94 cm.
• Drill 2 holes in the installation surface.
When drilling or tightening screws, make sure not to damage any cables, wires or
pipes located underneath the surface.
• Insert wall anchors into the drill holes.
• Attach the two wall mounts using one screw each.
• Carefully push the product into the wall mount. Do not use any force.
Operation
• Connect the hollow plug of the power adapter to the socket on the product.
• Connect the power adapter to a common household wall socket.
• The following table explains the functions of all keys on the remote control.
Button
Function
ON
Switch on
OFF
Switch off
Static colour:
Increase brightness
FLASH, STROBE, FADE, SMOOTH modes:
Increase frequency or speed
Static colour:
Decrease brightness
FLASH, STROBE, FADE, SMOOTH modes:
Decrease frequency or speed
R
Red
G
Green
B
Blue
W
White
Colour keys
The colour of the light equals the colour of the key.
FLASH
Flashing colour change
Strobe light effect
STROBE
Select the colour beforehand.
FADE
Colour change with fading effect
SMOOTH
Colour change with chaser effect
Cleaning and care
• Switch off the product before cleaning. Disconnect the power adapter from the mains. Allow
the product to cool down completely.
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical
solutions since these can penetrate the housing or impair functionality.
• The product is maintenance-free except for occasional cleaning. There are no components
inside the product that require maintenance. So never open the product.
• Clean the product with a dry, fibre-free cloth.
• To prevent scratch marks, do not apply too much force on the product during cleaning.
• The LEDs are built-in and cannot be replaced.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
Remove any inserted (rechargeable) batteries and dispose of them separately from
the product.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used
(rechargeable) batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labeled with this symbol to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals
involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable)
batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our
stores or wherever (rechargeable) batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
a) LED tube
Operating voltage ......................... 12 V/DC
Power consumption ...................... 8 W
Number of LEDs ........................... 36
LED service life ............................. 50000 h
Beam angle .................................. 180°
Colour temperature ....................... 10000 K (white light)
Luminous flux ............................... 100 lm (white light)
Operating conditions ..................... -30 to +60 °C, 10 - 90 % RH
Storage conditions ........................ -40 to +70 °C, 10 - 90 % RH
Dimensions (Ø x L) ....................... 50 x 1000 mm
Weight .......................................... 330 g
b) Power adapter
Input voltage ................................. 100 – 240 V/AC, 50/60 Hz
Output voltage/current .................. 12 V/DC, 1 A
Cable length ................................. 150 cm
c) Remote control
Power supply ................................ 3 V button cell, (type CR2025)
Range ........................................... 3 m
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1518601_V1_0217_02_IPL_m_en
Advertisement
