Advertisement
(EN) ENGLISH
Only the techniques shown in the diagrams that are not crossed out
and/or do not display a skull and crossbones symbol are authorized.
Check our Web site www.petzl.com regularly to find the latest versions
of these documents.
Contact PETZL if you have any doubt or difficulty understanding these
documents.
1. Field of application
Belay / rappel device for climbing and mountaineering.
Compatible with 7.5 to 11 mm CE (EN 892) and/or UIAA certified
dynamic ropes (core + sheath).
This product must not be loaded beyond its strength rating, nor be
used for any purpose other than that for which it is designed.
WARNING
Activities involving the use of this equipment are inherently
dangerous.
You are responsible for your own actions and decisions.
Before using this equipment, you must:
- Read and understand all instructions for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings may result in severe injury
or death.
You must also be familiar with rescue techniques so that a rescue may
be immediately carried out in case of difficulties encountered while
using this product. This implies an adequate training in the necessary
rescue techniques.
Responsibility
WARNING, specific training in the activities defined in the field of
application is essential before use.
This product must only be used by competent and responsible
persons, or those placed under the direct and visual control of a
competent and responsible person.
Gaining an adequate apprenticeship in appropriate techniques and
methods of protection is your own responsibility.
You personally assume all risks and responsibilities for all damage,
injury or death which may occur during or following incorrect use of
our products in any manner whatsoever. If you are not able, or not in
a position to assume this responsibility or to take this risk, do not use
this equipment.
2. Nomenclature of parts
(1) Cable, (2) Body, (3) Rope slots, (4) Braking grooves.
Principal materials: aluminum alloy body and nylon-coated steel cable.
3. Inspection, points to verify
Before each use
Verify that the product is free of cracks, deformation, marks, wear,
corrosion, etc.
Pay particular attention to sharp edges that can develop with use.
Consult the details of the inspection procedure to be carried out
for each item on the Web at www.petzl.com or on the PETZL PPE
CD-ROM. Contact PETZL if there is any doubt about the condition of
this product.
During each use
It is important to regularly monitor the condition of the product and
its connections to the other equipment in the system. Make sure that
the various pieces of equipment in the system are correctly positioned
with respect to each other. Take care to keep foreign objects out of the
rope slots.
4. Compatibility
For all of your applications, verify the compatibility of this product with
the other elements of your system (compatibility = good functional
interaction).
Ropes
For use with EN 892 dynamic half ropes (2 x 1/2 ropes), twin ropes,
or single rope.
When using two strands of rope, the two strands must be similar
(diameter, condition, texture).
WARNING, certain ropes may be slippery, for example new ropes,
small diameter ropes, certain sheath constructions and/or sheath
treatments, wet ropes, etc. (see the instructions specific to the rope).
Braking carabiner
You must use a locking carabiner. The brake bar, in contact with the
VERSO, must be as straight as possible.
5. Installation
- Clip a locking carabiner to the cable.
- Attach the VERSO to the belay loop of the harness.
- Single rope: insert a loop of rope into one of the rope slots.
- Half and twin ropes: insert a loop of rope into each of the two rope
slots.
- Clip the loop or loops of rope and lock the carabiner.
6. Warnings before and during use
The VERSO does not automatically stop the rope from sliding
through the device. The belayer must actively stop the rope from
sliding in order to arrest a fall.
Always keep a secure grip on the braking side of the rope.
The belayer must be anchored to the belay before belaying or
lowering a partner.
- The use of gloves is recommended.
- Before use, familiarize yourself with how your rope works with the
VERSO to get an idea of its braking capabilities.
Cable = 0 kN
The cable has no tensile strength.
WARNING DANGER, do not use the cable to anchor yourself.
The cable prevents the VERSO from moving too far away from the
carabiner and helps prevent loss of the device. To avoid damaging the
cable, take care to keep the rope from rubbing against it.
7. Belaying the leader
WARNING, the leader's rope must pass through a directional anchor.
7A. Giving slack.
With the hand gripping the braking side of the rope, push the rope
toward the VERSO, forming a loop. The hand on the climber's side of
the rope then pulls the slack rope through the VERSO.
7B. Taking up slack.
The hand on the climber's side regularly takes up the slack rope. The
hand on the braking side pulls the rope through the VERSO.
7C. Arresting a fall.
Pull firmly downward on the braking side of the rope.
8. Lowering a climber in a toprope
situation
Grip the braking side of the rope below the VERSO with both hands.
The belayer moves one hand over the other down the braking side of
the rope. Always keep a firm grip on the braking side of the rope.
9. Belaying the second with the rope
redirected through a top anchor
See chapte 5: Installation.
The second's rope must be redirected through the belay.
10. Abseil descent.
Install the two strands of rope in the VERSO as shown in chapter 5. To
brake, tighten your grip on the braking side of the ropes.
Use a rappel backup system (SHUNT or self-locking knot) below
the VERSO.
11. Adjusting the braking
In most cases, choose the position: braking side of the rope running in
the braking grooves (see chapter 5).
In other cases, adjust the braking position as needed for different user
weights, rope diameters, applications and weather conditions. For less
friction, reverse the rope path through the device. The braking side of
the rope runs over the side of the device opposite the braking grooves.
12. General information
Lifetime
WARNING, in extreme cases, the lifetime of the product can be
reduced to one single use through exposure to for example any of the
following: chemicals, extreme temperatures, sharp edges, major fall
or load, etc.
The maximum lifetime of Petzl products is as follows: up to 10 years
from the date of manufacture for plastic and textile products. It is
indefinite for metallic products.
The actual lifetime of a product ends when it meets one of the
retirement criteria listed below (see "When to retire your equipment"),
or when in its system use it is judged obsolete.
The actual lifetime is influenced by a variety of factors such as: the
intensity, frequency, and environment of use, the competence of the
user, how well the product is stored and maintained, etc.
Inspect equipment periodically for damage and/or
deterioration.
In addition to the inspection before and during use, a periodic
in-depth inspection must be carried out by a competent inspector.
This inspection must be performed at least once every 12 months.
The frequency of the in-depth inspection must be governed by the
type and the intensity of use. To keep better track of your equipment,
it is preferable to assign each piece of equipment to a unique user
so that he will know its history. The results of inspections should be
documented in an "inspection record". This document must allow
recording of the following details: type of equipment, model, name
and contact information of the manufacturer or distributor, means
of identification (serial or individual number), year of manufacture,
date of purchase, date of first use, name of user, all other pertinent
information for example maintenance and frequency of use, the history
of periodic inspections (date / comments and noted problems / name
and signature of the competent person who performed the inspection /
anticipated date of next inspection). See example of detailed inspection
record and other informational tools available at www.petzl.com/ppe
When to retire your equipment
Immediately retire any equipment if:
- it fails to pass inspection (inspection before and during use and the
periodic in-depth inspection),
- it has been subjected to a major fall or load,
- you do not know its full usage history,
- it is at least 10 years old and made of plastics or textiles,
- you have any doubt as to its integrity.
Destroy retired equipment to prevent further use.
Product obsolescence
There are many reasons why a product may be judged obsolete
and thus retired before the end of its actual lifetime. Examples
include: changes in applicable standards, regulations, or legislation;
development of new techniques, incompatibility with other
equipment, etc.
Modifications and repairs
Do not modify your product in any way unless the modification is
specifically authorized by Petzl. An unauthorized modification can
reduce the product's effectiveness.
Repairs made outside of Petzl facilities are prohibited. Contact Petzl if
your product needs repair.
Storage, transport
Dry your harness after use and store it in a bag.
Store it away from exposure to UV, moisture, chemical products, etc.
Traceability and markings
Do not remove any markings or labels. You must check to ensure that
the product markings remain legible during the entire lifetime of the
product.
Guarantee
This product is guaranteed for 3 years against any faults in materials
or manufacture. Exclusions from the guarantee: normal wear and
tear, oxidation, modifications or alterations, incorrect storage, poor
maintenance, damage due to accidents, to negligence, and to uses for
which this product was not designed.
PETZL is not responsible for the consequences, direct, indirect or
accidental, or any other type of damage befalling or resulting from the
use of its products.
Advertisement
