Table of Contents
Advertisement
COMPLETE THE INSTALLATION
NOTES: Do not plug in the power cord until all interface cables are connected.
NOTES: Make drip loops in all cables and cords.
□ Route the interface cable(s) in the wall from the valve location to the interface installation locations.
□ If not already installed, install the interface(s) at this time according to the instructions packed with
the product.
□ Connect the interface cable(s) to the valve.
□ Verify there is power to the electrical outlet.
□ Plug the power cord into the outlet.
INSTALLATION CHECKOUT
□ Turn on the water supply to the valve.
□ Check all connections for leaks and make any adjustments as needed.
□ Press the icon on the interface. The interface screen will be lit and the shower should be turned on.
NOTE: For more information about using the user interface and its menus, refer to the user interface.
□ Check for leaks and make any adjustments as needed.
□ Verify that the water flow is sufficient for your showering needs. Remove the regulator in the outlet of the
valve if needed.
NOTE: The maximum water temperature to the outlets is limited to 120°F (49°C). The valve will automatically
shut down if the temperature exceeds 120°F (49°C).
OPERATION INSTRUCTIONS
Showerhead
Temperature
Symbol
Setting Mark
Handshower
Symbol
Temperature Indicator
Remote Control
1354659-2A-C
How to Operate the Interface
Showerhead Symbol - (Top Button)
Turn showerhead On/Off.
Handshower Symbol - (Bottom Button)
Turn handshower On/Off.
NOTES: Showerhead and handshower can be used at
the same time.
Rotary movement selects showering temperature. The
larger the number which the temperature setting mark
is aligned, the higher the temperature. "C" is for full
cold water, "H" is for pre-set Max temperature.
NOTE: The factory default maximum temperature is
set to 45°C. And the default maximum time of water
outflow is 30 minutes，it will be turned off automatically
after 30 minutes.
When you turn on the product and water begins to
flow, the temperature indicator light will begin to flash
to show the product is warming up. Once the prese-
lected outlet temperature has been reached, the
indicator light will stop flashing.
Press the buttons on the handshower to change the
water flow.
Remote Control
Turn the shower On/Off.
Through the remote control, showerhead and
handshower will be turned off at the same time.
But only showerhead will be turned on by default.
SETTINGS
Temperature Setting Mark
Temperature Indicator
When the shower is in the off
position, hold down the showerhead
button for 10 seconds，the lights will
pulse slow to indicate setting mode.
CARE AND MAINTENANCE
Check Valve
Copper Tube
Nut
Screen
O-Ring
Seal
Hole
Hex Wrench
8
1354659-2A-C
Adjust temperature indicator according
Press the showerhead button to
to the table below to set desired
set the maximum temperature.
maximum temperature. The scale on
The temperature indicator light will
the indicator which the temperature
flash three times to confirm the
setting mark is aligned represents the
setting has been completed.
selected maximum temperature.
Caution! Make sure that the maximum
outlet temperature is suitable and safe
for all users.
Temp Indicator Position
Temp (°C)
C
Exit No Change
1 - 3
41
4 - 6
45
7 - 9
48
H
Exit No Change
Clean the Inlet Screen
Disconnect the power and turn off the water supply.
Unthread the plastic nuts from the hot and cold inlets.
Remove the copper tubes. The O-ring and screen may be
attached to the end of the tube.
If the screen remains in the check valve, use a small
flat-blade screwdriver to gently pull the check valve from the
valve inlets.
Remove the screens from the copper tubes or check valves.
Clean the screens to remove any dirt or debris. Rinse or
replace the check valves and screens. Reassemble the inlet
connections.
Clean the Handshower
Any debris or mineral build-up may cause distorted flow
stream or reduce the flow rate. To remove the debris or
mineral build-up, run water through the handshower, firmly
press or rub your finger back and forth across the rubber
nozzles.
Remove and clean the screen washer.
Uninstall the Button of the Interface
Insert one end of a hex wrench into the hole on the
backplate to remove the button, replace it if needed during
maintenance．
9
Advertisement
Table of Contents
