Otto Bock Avantgarde XXL 2 Instructions For Use Manual
  1. Manuals
  2. Brands
  3. Otto Bock Manuals
  4. Wheelchair
  5. Avantgarde XXL 2
  6. Instructions for use manual

Otto Bock Avantgarde XXL 2 Instructions For Use Manual

Hide thumbs Also See for Avantgarde XXL 2:
Table of Contents

Advertisement

Quick Links

Download this manual
Avantgarde XXL 2
Instructions for use (qualified personnel) .................................................................
3

Advertisement

Table of Contents
loading

Related Manuals for Otto Bock Avantgarde XXL 2

Summary of Contents for Otto Bock Avantgarde XXL 2

  • Page 1 Avantgarde XXL 2 Instructions for use (qualified personnel) ..............
  • Page 2 Avantgarde XXL 2...

  • Page 3: Table Of Contents

    ........................... 6.11 Installing and adjusting the head support ....................Delivery ................................Final inspection ..........................Transport to the customer ........................Handing over the product ........................Maintenance and repair ........................... Disposal ................................Disposal information ..........................Information on re-use ........................... Avantgarde XXL 2...
  • Page 4 Table of contents Legal information .............................. 10.1 Liability .............................. 10.2 Warranty ............................10.3 Service life ............................Technical data ..............................Appendices ................................ 12.1 Required tools ............................ 12.2 Torque values of the screw connections ....................Avantgarde XXL 2...

  • Page 5: Foreword

    The tasks described below may only be carried out by qualified personnel. Compliance with all manufacturer spe­ cifications and all applicable legal provisions is required. Please contact the manufacturer’s service department for further information (see inside or outside of rear cover for addresses). Avantgarde XXL 2...

  • Page 6: Safety

    The nameplates are found on the frame. Label Meaning A Manufacturer’s product name B CE marking C Maximum load (see section “Technical data”) D Manufacturer information/address E Serial number F Manufacturing date G Symbol for medical device Avantgarde XXL 2...

  • Page 7: Delivery

    (e.g. in the vicinity of radiators or in case of exposure to strong sunlight behind glass), the tyres may become permanently deformed. 5 Preparing the product for use 5.1 Assembly CAUTION Exposed pinch points Crushing, pinching due to incorrect handling ► When folding the wheelchair out or together, only grip by the specified components. Avantgarde XXL 2...

  • Page 8: Settings

    All parts of the product should be cleaned thoroughly before adjustments are made. The tools required for adjustments and maintenance tasks as well as the torque values for screw connections are listed in the section "Appendices" (see Page 27). Avantgarde XXL 2...

  • Page 9: Adjusting The Drive Wheels

    5) Tighten the Allen head screws on the drive wheel adapter to 10 Nm (see fig. 1, item 1). Put on the protective cap. 6) If necessary: Readjust the height and alignment of the caster attachment device as well as the wheel locks (see information at the start of the section). Avantgarde XXL 2...

  • Page 10: Adjusting The Drive Wheels Vertically

    INFORMATION: Once changed, the left and right quick-release axle mountings must both have the same vertical position in the frame. 8) If necessary: Readjust the height and alignment of the caster attachment device as well as the wheel locks (see information at the start of the section). Avantgarde XXL 2...

  • Page 11: Adjusting The Quick-Release Axle

    All handrims are designed for a spacing from the drive wheel of 15 mm (standard setting) and 25 mm. 1) Loosen/remove the handrim screw connection from the rim (see fig. 6). 2) Tightly screw the handrims onto the rim in narrow or wide installation position. Avantgarde XXL 2...

  • Page 12: Adjusting The Caster Wheels

    5) Install the caster wheel. 6) Push on the 2nd spacer bushing (see fig. 10, item 1). 7) Tighten the threaded axle to 8 Nm. → Once changed, the left and right caster wheels must have the same vertical position in the caster fork. Avantgarde XXL 2...

  • Page 13: Adjusting The Wheel Locks

    → The wheel lock bolt must lock the drive wheel securely when stationary. 4) Tighten the Allen head screws to 10 Nm. → After adjustment, the left and right knee lever wheel locks must both have the same braking force. max. 5 mm Avantgarde XXL 2...

  • Page 14: Adjusting The Knee Lever Wheel Lock For User And Attendant

    2) Adjust the knee lever wheel lock by sliding it. When the wheel lock is disengaged, the gap between the tyre and wheel lock bolt must not exceed 5 mm (sim­ ilar illustration: see fig. 14). Avantgarde XXL 2...

  • Page 15: Adjusting The Braking Force Of The Drum Brake

    2) Screw in the adjustment screw (see fig. 18, item 2) until the scraping noise at the rear wheel disappears and the wheel runs freely. 3) Tighten the counter nut (see fig. 18, item 1) until the adjustment screw is fixed. → The braking force of both rear wheels must be adjusted equally. Avantgarde XXL 2...

  • Page 16: Adjusting The Back Support

    1) Slightly loosen the Allen head screw on the locking joint on both sides (see fig. 20, item 1). 2) Position the back support unit at the desired angle. 3) Tighten the Allen head screw on the locking joint to 10 Nm on both sides. Avantgarde XXL 2...

  • Page 17: Adjusting The Back Support Upholstery / Seat Upholstery

    You can slightly correct the centre of gravity by making small changes to the dip of the seat upholstery. However, larger corrections to the centre of gravity must be made by making changes to the settings on the frame, the axle unit and the caster wheels. 1) Remove the seat cushion and slightly fold the crossbrace. Avantgarde XXL 2...

  • Page 18: Adjusting The Leg Supports

    The leg support angle setting should be chosen so that the ankle is in a relaxed, comfortable position. 1) Loosen the Allen head screws on the rear foot plate suspension by several turns (see fig. 26). 2) Turn the foot plate to the desired angle. 3) Tighten the Allen head screws to 10 Nm (see fig. 26). Avantgarde XXL 2...

  • Page 19: Adjusting The Lateral Heel Blocks

    1) Forearm support height adjustment: Push the release button on the outside of the side panel and adjust the height (see fig. 28, item 1). 2) Forearm support depth adjustment: Adjusting the depth of the forearm support is not possible with this side panel. Avantgarde XXL 2...

  • Page 20: Adjusting The Anti-Tipper

    2) Loosen the second Allen head screw on the angle adjuster (see fig. 31, item 3). 3) Set the angle of the pivot arm. 4) Bolt down the pivot arm. The max. distance between the anti-tipper rollers and floor is 50 mm (see fig. 32). max. 50 mm Avantgarde XXL 2...

  • Page 21: Adjusting The Lap Belt

    4) Angle adjustment: Loosen the mounting screws on the head support and adjust the angle (see fig. 34, item 4). 5) Once all settings have been adjusted, firmly close the clamping lever and tighten the mounting screws. 6) Position the stop on the adjustment tube and tighten (see fig. 33, item 4). Avantgarde XXL 2...

  • Page 22: Delivery

    The manufacturer recommends regular maintenance of the product every 12 months. Further information on caring for the product and on maintenance/repair can be found in the instructions for use (user). Detailed information on repairs can be found in the service manual. Avantgarde XXL 2...

  • Page 23: Disposal

    ► Note that not all adjustment possibilities can be used with all product versions. Furthermore, the adjustment combinations are limited by the compact frame geometry. ► Technical changes and tolerances are reserved by the manufacturer. Avantgarde XXL 2 Max. load [kg] Transport weights [kg] Frame: from 11.3...
  • Page 24 Technical data Avantgarde XXL 2 24" drive wheel: from 1.3 (including quick-release axle) Min. tyre pressure [bar] Permissible tyre type – drive wheels Pneumatic tyres, PU tyres Permissible tyre type – caster wheels Solid rubber, pneumatic tyres, soft caster 3)4)5) Maximum permissible inclination [°]/[%]...
  • Page 25 Foot plate bar, long (320 mm) Specification for seat depth 380 mm Specification for seat depth 420 mm Min. Max. Min. Max. XXL 2 --- = Combination not possible. All specifications for narrow handrim installation (in case of wide installation: +20 mm). Avantgarde XXL 2...
  • Page 26 Between the front and rear axle position, the axle can be adjusted horizontally in increments of 15 mm (see rear frame component, item A, B, C, D, E, F, G; see fig. 36). Overall width [mm] Seat width Standard side pan­ Side panel with forearm Drive wheel with drum el/clothing guard support (height- brake adjustable) Avantgarde XXL 2...
  • Page 27 12.2 Torque values of the screw connections Unless otherwise specified, screw connections are tightened with the following torque values: • Thread diameter M4: 3 Nm • Thread diameter M5: 5 Nm • Thread diameter M6: 10 Nm • Thread diameter M8: 25 Nm Avantgarde XXL 2...
  • Page 28 Avantgarde XXL 2...
  • Page 29 Avantgarde XXL 2...
  • Page 30 Avantgarde XXL 2...
  • Page 31 · www.ottobock.de 143441 Moscow Region/Krasnogorskiy Rayon info@ottobock.com.co · www.ottobock.com.co Russian Federation Otto Bock Healthcare Products GmbH Otto Bock de Mexico S.A. de C.V. T +7 495 564 8360 · F +7 495 564 8363 Brehmstraße 16 · 1110 Wien · Austria Prolongación Calle 18 No. 178-A info@ottobock.ru · www.ottobock.ru F +43 1 5267985...
  • Page 32 Ihr Fachhändler | Your specialist dealer Otto Bock Mobility Solutions GmbH Lindenstraße 13 · 07426 Königsee/Germany www.ottobock.com...

Table of Contents