Related Manuals for LEAB TS 12
Summary of Contents for LEAB TS 12
- Page 1 DC-DC BATTERY CHARGER TS 12/12-03 USER MANUAL VERSION 7 14/07/2021 www.leab.eu LEAB Automotive GmbH Thorshammer 6 24866 Busdorf...
-
Page 2: Table Of Contents
Table of Contents LEAB Automotive GmbH Table of Contents 1 About this Manual ........................ 2 General Safety........................Intended Use....................... Foreseeable Misuse....................3 Technical Specifications ....................4 Package Contents ......................... 5 About this Product ....................... 6 Assembly ..........................7 Installation .......................... -
Page 3: About This Manual
Skilled workers in the field of automotive electrics. Any modifications to the product or its components are prohibited and do not conform to its intended use. Only use original LEAB or LEAB-approved accessor- ies. Throughout the manual, you will be alerted to warnings and safety notices about potential hazards associated with handling the device. -
Page 4: General Safety
2 General Safety LEAB Automotive GmbH DANGER Danger that will lead to severe injury or death Safety instructions with the signal word Danger indicate a hazard which, if not avoided, will result in death or severe injury. Read the safety instructions carefully and follow them to avoid the hazard. -
Page 5: Intended Use
LEAB Automotive GmbH 2 General Safety WARNING Risk of fire from overheated battery Flammable gases can escape if the battery overheats. 1. Always charge batteries in well-ventilated rooms and away from ignition sources. Notice Device defects from incorrect installation Incorrect installation can result in device defects. -
Page 6: Technical Specifications
4 Package Contents LEAB Automotive GmbH 3 Technical Specifications Part number Output lead 0431212040 DIN 14690 0432412039 MagCode Tab. 1: TS 12/12-03 TS 12/12-03 Battery type Wet, gel, AGM Battery capacity 6 Ah ... 25 Ah Charging current 3 A (4 A) Input voltage 12 V (10 V ... -
Page 7: About This Product
LEAB Automotive GmbH 5 About this Product 5 About this Product The DC-DC TS battery charger is especially suitable for trickle charging and re- charging batteries in technical equipment (e.g. starter batteries for portable pumps or generators). They are designed for charging lead batteries (wet, gel and AGM) and have overvoltage and overheating protection. -
Page 8: Assembly
7 Installation LEAB Automotive GmbH Fig. 2: Installation Clip TS Battery Charger 6 Assembly To mount the battery charger, proceed as follows: ü Choose a cool, dry and well-ventilated assembly site. 1. Remove the installation clip (5). CAUTION! To avoid damaging the lock (4), release the installation clip from the left side. - Page 9 7 Installation 3. Secure the positive cable as close as possible to the vehicle battery with a suitable fuse. NOTE! TS 12/12-03: 5 A. 4. Connect the black wire of the input lead (1) to the negative terminal of the vehicle battery.
-
Page 10: Operation
10 Troubleshooting LEAB Automotive GmbH 8 Operation To charge a battery in technical equipment, proceed as follows: ü The battery charger is mounted and installed. ü The operating display (3) is lit green. 1. Connect the output lead (2) to the socket on the technical equipment. -
Page 11: Disposal
The system must not be disposed of with household waste. Take it to a recycling point or return it to your point of sale. 12 EU Declaration of Conformity The Charger TS 12/12-03 complies with the requirements of the following directives: – 2014/30/EU: EMV –... - Page 12 Tel: +49 (0) 4621 9 78 60-0 Fax: +49 (0) 4621 9 78 60-260 info@leab.eu It is prohibited to copy, duplicate, translate or otherwise pass on the content of this guide to third parties without the express written permission of LEAB.