Advertisement
Quick Links
LEVEL 1
PRODUCT AND CONSUMER WARNING
CHOKING HAZARD: This product contains small parts and is not intended for children under 3.
• This product is intended for users 8 years of age and older.
• To avoid choking, keep small parts away from children.
• Use caution—this product contains parts with sharp edges.
• To avoid potential damage to the product, only insert the included marbles into the elevator.
Advertisement
Related Manuals for Spacerails Level 1
Summary of Contents for Spacerails Level 1
- Page 1 LEVEL 1 PRODUCT AND CONSUMER WARNING CHOKING HAZARD: This product contains small parts and is not intended for children under 3. • This product is intended for users 8 years of age and older. • To avoid choking, keep small parts away from children.
-
Page 2: Parts Included
Wire Cutters or Utility Scissors Pen or Marker 3 AA Batteries (newer models) or 1 C Battery Rail Coupling Marble Rail Rail Clip 5000 mm Ruler (in centimeters) Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 2... - Page 3 Assembly. Attach the Loop Stand Corner pieces. to the bottom of the Loop. RAIL SPLITTER Prepare Rail Splitter: Attach one Rail Clip to each of the Rail Splitter posts. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 3...
-
Page 4: Base Assembly
Illustration of Shafts are 1:2.3 or (approximately 43%) of scale. 261 mm 240 mm 238 mm 194 mm 199 mm 264 mm 159 mm 204 mm 129 mm 101 mm 63 mm 47 mm Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 4... -
Page 5: Elevator Assembly
Elevator Rings over the onto the top of the elevator each of the Elevator Rings, then to three shafts. assembly. the right side of the Rail Clip. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 5... - Page 6 Please see the included addendum showing the 1:1 ratio. This will help with rail cuts and positioning of arms and corners. 174mm 275mm 313mm 416mm 420mm 487mm Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 6...
- Page 7 LOOP PART SHAFT B SHAFT D PUSH SHAFT E SHAFT A SHAFT C Step 3: Attach the Loop, Power Box and all shafts to the base. LOOP ELEVATOR Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 7...
- Page 8 Smooth rails for efficient travel: Make sure the rails the rails close to the Elevator Helix to ensure the Marble connect smoothly and are free of any bumps, twists, enters the rollercoaster smoothly. or kinks. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 8...
- Page 9 Step 2: Connect both G Rail sections between the entrance of the loop and the front section of the Rail Splitter. Step 3: Connect both I Rail sections between the bottom entrance of the elevator and the bottom front corner of shaft A. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 9...
- Page 10 Step 5: Connect both H Rail sections between the exit of the elevator and the front top corner of shaft A. Step 6: Connect both B Rail sections between the front top corner of shaft E and the single side of the Rail Splitter. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 10...
- Page 11 Step 9: Connect both F rail sections between the front corner of shaft C and the front bottom corner of shaft E. Step 10: Connect both C rail sections between the front corner of shaft D and the middle entrance of the elevator. Seaich Corporation, LLC. All rights reserved. www.seaich.com | Spacerails, LLC. www.spacerails.com Page 11...
- Page 12 Seaich Corporation 1910 West 1040 South Salt Lake City, UT 84104 (833) 732-4242 orders@seaich.com Spacerails LLC www.spacerails.com...
Need help?
Do you have a question about the Level 1 and is the answer not in the manual?
Questions and answers