Table of Contents
Advertisement
Quick Links
Controlled document: M-0002B
I N P R E S S T S
Revision: B
Issue Date: 30 August 2021
C on te nt s
1 USER GUIDE
1 Key Features
2 WARNING
3 CONTROLLER APPEARANCE
4 FUNCTIONS
5 OPERATING INSTRUCTIONS
5 Enter Setup Mode
6 Change Date and Time
6 Change Pressure Setpoint
6 Change ALarm Setpoint
7 Enable / Disable Buzzer
7 Change Alarm DELAY Settings
7 Change Service Reminders
8 Calibrate Zero Sensor
8 Reset Data Log
8 Test Inputs Option
9 TECHNICAL DETAILS
9 Map of Functions
11 General Arrangement
12 Connector Pinout Details
14 Installation
15 Fan Speed Control Output
15 Mounting
15 Supply Power
15 Calibration
15 Control Override
16 Data Logging Information
20 BREATHESAFE WARRANTY
21 CONTACT US
© BREATHESAFE 2021
USER GUIDE
The new BreatheSafe INPRESS TS cabin pressure controller specifically
designed to monitor, record and intelligently control the cabin
pressure inside a vehicles cabin or electrical enclosure.
Efficient cabin air filtration and pressure management ensure harmful
dust and toxic fumes cannot ingress into the cab and be inhaled by
operators.
The INPRESS TS has auto pressure control allowing the end user
to easily maintain a set cabin pressure. RS20R and ISO23875
recommend over 20Pa if a cabin pressure monitor is installed.
BreatheSafe recommend 30Pa with the alarm point being 10Pa.
The controller has a built in 14-bit digital pressure senor that can
accurately measure pressures between 0 and 2000 pascals with
repeatable accuracy.
An alarm setpoint can be set via the user keypad between the range
of 5.0 and 1000 Pascals.
Controlled document:
When the pressure within the cabin falls below the alarm setpoint,
Issue Date:
there will be a (user set) delay and alarm will sound, and warning
flash on main screen.
PAGE 1
www.breathe-safe.com.au
KEY FEATURES
Digital cabin pressure monitoring system
Automatic cabin pressue control
Intelligent fan speed output
Data logger
Alarm for low pressure
Light sensor for automatic dimming of screen
Delivering Innovative Climate Solutions Worldwide
Advertisement
Table of Contents
Summary of Contents for BreatheSafe INPRESS TS
- Page 1 6 Change Date and Time operators. 6 Change Pressure Setpoint Light sensor for automatic dimming of screen The INPRESS TS has auto pressure control allowing the end user 6 Change ALarm Setpoint to easily maintain a set cabin pressure. RS20R and ISO23875 7 Enable / Disable Buzzer recommend over 20Pa if a cabin pressure monitor is installed.
- Page 2 15 Control Override 16 Data Logging Information THE PRESSURISER HAS VARIOUS TYPES OF ROTATING EQUIPMENT INSTALLED. ENSURE ALL SAFETY GUARDS 20 BREATHESAFE WARRANTY ARE IN PLACE WHILE THE SYSTEM IS RUNNING. 21 CONTACT US © BREATHESAFE 2021 PAGE 2 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
-
Page 3: Controller Appearance
15 Fan Speed Control Output 15 Mounting Current measured Alarm button Alarm 15 Supply Power cabin pressure in Pascals 15 Calibration Button 15 Control Override 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US Light Sensor © BREATHESAFE 2021 PAGE 3 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide... - Page 4 LOW PRESSURE ALARM 6 Change Pressure Setpoint safety and minimised distraction 6 Change ALarm Setpoint If the cabin pressure falls below the alarm setpoint, INPRESS TS will 7 Enable / Disable Buzzer wait the designated delay time before alarming user. 7 Change Alarm DELAY Settings...
-
Page 5: Enter Setup Mode
6 Change Date and Time 6 Change Pressure Setpoint 6 Change ALarm Setpoint SETUP PARAMETERS 7 Enable / Disable Buzzer Placing the BreatheSafe INPRESS TS unit into Setup mode allows the 7 Change Alarm DELAY Settings adjustment of the following parameters: 7 Change Service Reminders •... -
Page 6: Change Date And Time
Site Access Button > Adjust Setpoint. 9 TECHNICAL DETAILS The pressure setpoint changes the pressure that the cabin will be 9 Map of Functions Controlled document: maintained. INPRESS TS keeps a higher pressure within the cabin 11 General Arrangement compared to outside. Issue Date: 12 Connector Pinout Details Enter Setup mode and select ADJUST SETPOINT button. -
Page 7: Enable / Disable Buzzer
6 Change ALarm Setpoint Site Access Button > Alarm Setting. 7 Enable / Disable Buzzer The Alarm Delay adjusts the length of time between the INPRESS TS 7 Change Alarm DELAY Settings measuring low pressure and sounding the alarm. Low pressure can 7 Change Service Reminders occur when a door or window is opened momentarily, not requiring 8 Calibrate Zero Sensor... - Page 8 Enter Site Menu and select the FACTORY SETTINGS button. Then, press the LOG SETTINGS button. Press the CLEAR LOG FILE button to 9 TECHNICAL DETAILS reset. The BreatheSafe INPRESS TS unit will start to data log from the 9 Map of Functions Controlled document: first memory location once again.
-
Page 9: Technical Details
11 General Arrangement Issue Date: 12 Connector Pinout Details 14 Installation 15 Fan Speed Control Output 15 Mounting 15 Supply Power 15 Calibration 15 Control Override 16 Data Logging Information factory settings NEXT PAGE 20 BREATHESAFE WARRANTY 21 CONTACT US © BREATHESAFE 2021 PAGE 9 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide... - Page 10 Controlled document: CONTINUED 11 General Arrangement Issue Date: 12 Connector Pinout Details 14 Installation 15 Fan Speed Control Output 15 Mounting 15 Supply Power 15 Calibration 15 Control Override 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US © BREATHESAFE 2021 PAGE 10 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
-
Page 11: General Arrangement
9 Map of Functions Controlled document: 11 General Arrangement Issue Date: 12 Connector Pinout Details 14 Installation 15 Fan Speed Control Output 15 Mounting 15 Supply Power 15 Calibration 15 Control Override 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US © BREATHESAFE 2021 PAGE 11 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide... -
Page 12: Connector Pinout Details
Window Input (+) 14 Installation Pin 12 0V Negative Ground 15 Fan Speed Control Output 15 Mounting 15 Supply Power 15 Calibration 15 Control Override 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US Please do not scale © BREATHESAFE 2021 PAGE 12 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide... - Page 13 Breathe Safe Pty Ltd.,Head Office: 62 Mica Street, Carole Park QLD 4300 Australia, Western Australia: 169 Chisholm Crescent, Kewdale WA 6105, Tel: +61 7 3276 7833 A.C.N. 109689 803 / A.B.N. 42 109 689 803 © BREATHESAFE 2021 PAGE 13 www.breathe-safe.com.au...
-
Page 14: Installation
15 Calibration inside of the cabin. When entrance door is fully closed then 15 Control Override close the window to begin the test. 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US © BREATHESAFE 2021 PAGE 14 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide... -
Page 15: Control Override
7 Change Alarm DELAY Settings The TS unit is designed to be dashboard mounted and utilizes a At the back of the INPRESS TS unit there is a small switch, this will 7 Change Service Reminders proprietary housing to secure the unit. Mounting can be in any turn off INPRESS control and run High Pressure Air Filtration unit by 8 Calibrate Zero Sensor... -
Page 16: Download Log File
Pressing this button begins the output of the log data to the terminal 15 Control Override This time period is shortened if the BreatheSafe INPRESS TS unit software installed on your computer. The logging intervals for the real 16 Data Logging Information experiences many alarms throughout each day. - Page 17 15 Supply Power in your computer. 15 Calibration Baud Rate: 57600 15 Control Override Data: 8 bit 16 Data Logging Information Parity: EVEN 20 BREATHESAFE WARRANTY Stop: 2 bit 21 CONTACT US Flow Control: NONE © BREATHESAFE 2021 PAGE 17 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
- Page 18 16 Data Logging Information setup and COM PORT settigns will be loaded ready to 20 BREATHESAFE WARRANTY download the data file from 21 CONTACT US the TLUCPMTS unit. © BREATHESAFE 2021 PAGE 18 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
- Page 19 Fields are: 16 Data Logging Information 3 = door open date, time, motor (volts) 20 BREATHESAFE WARRANTY output, cabin pressure (Pa), 21 CONTACT US cabin pressure preset (Pa), cabin low pressure alarm (Pa). © BREATHESAFE 2021 PAGE 19 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
- Page 20 11 General Arrangement Issue Date: 12 Connector Pinout Details 14 Installation 15 Fan Speed Control Output 15 Mounting 15 Supply Power 15 Calibration 15 Control Override 16 Data Logging Information 20 BREATHESAFE WARRANTY 21 CONTACT US © BREATHESAFE 2021 PAGE 20 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...
- Page 21 15 Mounting 15 Supply Power Email 15 Calibration sales@breathe-safe.com North America distributor 15 Control Override International Service and Supply 16 Data Logging Information 10740 181 Street NS 20 BREATHESAFE WARRANTY Edmonton Alberta 21 CONTACT US www.issminesafey.com © BREATHESAFE 2021 PAGE 21 www.breathe-safe.com.au Delivering Innovative Climate Solutions Worldwide...