Advertisement
Quick Links
"WIDE BODY'' FORAGE BOX
OPERATOR'S MANUAL &
PARTS LIST
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT.
UNSAFE OPERATION OR MAINTENANCE
WARNING
OF THIS EQUIPMENT CAN RESULT IN
INJURY OR DEATH.
HSMFG0316
Manufactured By
H&S MANUFACTURING CO., INC.
P.O. BOX 768 • (715) 387-3414 FAX (715) 384-5463
MARSHFIELD, WISCONSIN 54449
Advertisement
Related Manuals for H&S WIDE BODY
Summary of Contents for H&S WIDE BODY
- Page 1 “WIDE BODY’’ FORAGE BOX OPERATOR'S MANUAL & PARTS LIST READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE WARNING OF THIS EQUIPMENT CAN RESULT IN INJURY OR DEATH. HSMFG0316 Manufactured By H&S MANUFACTURING CO., INC. P.O. BOX 768 • (715) 387-3414 FAX (715) 384-5463...
- Page 2 CONTENTS Warranty & Warranty Registration Card ............. . 1-2 Dealer Pre-Delivery &...
- Page 5 DEALER PRE-DELIVERY CHECK LIST After the Forage Box has been completely set-up, check to be certain it is in correct running order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. Forage Box was not damaged in shipment.
- Page 6 SAFETY INFORMATION ALERT! YOUR SAFETY INVOLVED. THIS SYMBOL USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME CAREFUL. REMEMBER: CAREFUL OPERATOR BEST OPERATOR. MOST ACCIDENTS CAUSED HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. H&S MANUFACTURING CO.
- Page 7 SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices.
- Page 9 TRACTOR: This Operators Manual uses the term "Tractor" when identifying the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH; BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
- Page 10 Make sure to read and understand the main feeder apron adjustments. Located on the front of the Wide Body Box is a convenient hanger (Item A) for the hydraulic hoses. When the Wide...
- Page 11 OPERATION After you have run the Forage Box for several minutes, checked it over thoroughly as suggested in earlier recommendations, and have properly adjusted and lubricated it, you are ready to place your Power Box into operation. UNLOADING 1. Park the Forage Box on level ground whenever possible during unloading. 2.
- Page 12 MAIN APRON ADJUSTMENT Main feeder apron adjustment bolts are located behind the convenient access door located in the bottom portion of front gate. Remove handle nuts (A) to open access panel and swing door downward (Chassis or Running Gear Mount Only). On truck mount, remove 4 handle nuts and remove access panel. All apron chains must be taken up evenly before you use the power box.
- Page 13 This will lengthen the life of the sprockets and chain. Lubricate chains often. GREASE ZERKS There are multiple grease fittings on your “WIDE BODY’’ FORAGE BOX. Grease daily during normal use and before and after storage. Use a good grade of high quality grease.
- Page 14 IF THE POWER BOX IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION. Listed below are the decals on your “Wide Body’’ Forage Box. These decals may be ordered individually by part number or by ordering complete set. ITEM PART NO.
- Page 15 DECAL LOCATION INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized H&S Dealer. He will be able to give you faster service if you will provide him with the following: 1. Model & Serial Number – Both are located on the left hand rear upright. 2.
- Page 16 FIGURE 1 BOX ASSEMBLY -14-...
- Page 17 FIGURE 1 BOX ASSEMBLY ITEM PART NO. PART NO. DESCRIPTION POLY BONDED SIDES ALUMINIZED SIDES 22’ 24’ 18’ 20’ 22’ IFB25 IFB26 IFB128 IFB24 IFB25 Main Frame PB111 “ “ “ “ Light Bracket PB146 “ “ “ “ Center Floor Ridge IFB149 “...
- Page 18 FIGURE 2 REAR DOOR & DRIVE SYSTEM -16-...
- Page 19 FIGURE 2 REAR DOOR & DRIVE SYSTEM ITEM PART NO. PART NO. DESCRIPTION POLY BONDED SIDES ALUMINIZED SIDES 22’ 24’ 18’ 20’ 22’ “ “ “ “ Idler Shaft “ “ “ “ Idler sprocket “ “ “ “ Idler shaft spacer WM210 “...
- Page 20 FIGURE 3 OPTIONAL BARN DOORS -18-...
- Page 21 FIGURE 3 OPTIONAL BARN DOORS ITEM PART NO. DESCRIPTION GD13 10’ 2-Wire Cable GD19 Left Door Seal 16SV316 Control Box 16SV317 Control Box Gasket 16SV318 Control Box Cover 16SV235 Switch Boot WM109 2 Position Momentary Switch 16SV231 Fuse Holder 16SV232 5 Amp Fuse GD20 Decal...
- Page 22 FIGURE 4 HYDRAULIC GATE DELAY -20-...
- Page 23 FIGURE 4 HYDRAULIC GATE DELAY ITEM PART # DESCRIPTION 69912 STOP, GATE DELAY 60257 PIN WELDMENT 60404 STAKE SPACER YWFL12005 WASHER, FLAT, 3/8 USS YBHH12145 BOLT, 3/8 X 3-1/2 GR 5 YNRL12005 HEX NUT, REVERSIBLE-SIDE LOCK, 3/8-16 YBHH12185 BOLT, 3/8 X 4-1/2 GR 5 YPCT06020 COTTER PIN, 3/16 X 2 60192...
- Page 24 FIGURE 5 AIR GATE DELAY -22-...
- Page 25 FIGURE 5 AIR GATE DELAY ITEM QTY. PART # DESCRIPTION 60257 PIN WELDMENT 60404 STAKE SPACER YWFL12005 WASHER, FLAT, 3/8 USS 69912 STOP, GATE DELAY YBHH12160 BOLT, 3/8 X 3-3/4 YNRL12005 HEX NUT, REVERSIBLE-SIDE LOCK, 3/8-16 YBHH12185 BOLT, 3/8 X 4-1/2 GR 5 YBHH16115 BOLT, 1/2 X 3-1/2 GR 5 GD52 3-1/4"...
- Page 26 FIGURE 6 BARN DOOR 2-1/2” X 8” AIR CYLINDER COMPLETE CYLINDER ITEM PART NO. DESCRIPTION GD46 Rod Cap GD47 Base Cap GD48 Seal Kit GD49 Complete Cylinder (2-1/2” x 8”) -24-...
- Page 27 FIGURE 7 HAND CONTROLLER ITEM QTY PART # DESCRIPTION 61564 61597 FUSE, BLADE, 5AMP 16SV235 SWITCH BOOTS 61598 HAND CONTROLLER (ON-OFF) 58793 LOCKING WEDGE FOR DT06-2S CONNECTOR 56760 DEUTSCH SOCKET, SOLID, 14-16 GA. 58790 DEUTSCH 2 PIN PLUG HOUSING -25-...
- Page 28 FIGURE 1 LIGHTING WIRING CODE White - Ground Yellow - LH Flashing & Turn Signal Green - RH Flashing & Turn Signal Brown - Tail Lamp Red - Tail Lamp (Flash LH/RH) ITEM PART NO. DESCRIPTION S308 Rubber Light Mount S309 Amber Light S310...
- Page 30 H&S MFG H&S MFG ..CO CO ..H&S MFG H&S MFG H&S MFG products approved for the FEMA FEMA FEMA FEMA FEMA SEAL OF Q SEAL OF Q U U U U U ALITY ALITY ALITY SEAL OF Q...