Denon AVR-X3300W Service Manual page 164

Error USB Update Error
Details of Error code
Code Display
NACK received in response or
60 no response from Sub for the
Update Error**60
"P" command.
Mismatched Check Sum in
61 response or no response from
Update Error**61
Sub for the "I" command.
Failed to start up Sub in
62 Power On sequence during
Update Error**62
Update.
Update Error**63 Failed to transit to Application
63
Mode.
Update Error**64 Failed to transit to Boot
64
Loader Mode.
Write Enable Latch Bit not
80 set in Read after issuing the
Update Error**80
"WREN" command.
Update Error**81 Block Erase failed in Read after
81
issuing the "BE" command.
Update Error**82 No Update Packet received
82
from CY920 (Time Out).
Abnormal data in Update
83 Packet received from CY920
Update Error**83
(CRC Error).
Abnormal data in Update
84 Packet received from CY920
Update Error**84
(Packet No Error).
Update Error**85 Setup failure of the XModem
85
transfer method
Mismatched Check Sum in
86 Check Sum comparison after
Update Error**86
rewriting.
Remedies
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
164
Error USB Update Error
Details of Error code
Code Display
A2 Update Error**A2 Unable to detect USB.
A3 Update Error**A3 No Firmware File in USB.
The Firmware File in the USB
A4 does not support your model
Update Error**A4
and area.
Error notification received
A6 while requesting the Firm-
Update Error**A6
ware Info.
Update Error**A7 Time Out while obtaining
A7
Firmware information.
Update Error**AE Unable to detect USB for
AE
Firmware Download.
Update Error**AF No Firmware File for Firmware
AF
Download.
Time Out in Download (writ-
B1 ing to SDRAM) for Firmware
Update Error**B1
Download.
Update Error**B2 Error notification received af-
B2
ter rewriting the CY920 Firm.
Update Error**B3 Error in Firmware Update
B3
(Time Out).
Update Error**B4 Failed to transit to Boot
B4
Loader Mode.
Update Error**B5 Failed to transit to Application
B5
Mode.
---Checking the firmware version after updating---
After updating the firmware, check the version.
See "1. Version Display Mode"
Remedies
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Make sure the model name and area of
the Firmware File, Unplug and recon-
nect the AC plug, and try again.
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.