Denon AVR-X3300W Service Manual page 128

Paths to be confirmed Display
fig.04a
4 HDMI
A05:HDMI
fig.04b
Analog AD fig.05a
5
A06:AD
(MAIN) fig.05b
Analog Amp Assign
6 (Amp Assign : fig.06
A07:ASSIGN-Z2
ZONE2)
Amp Assign
fig.07a
7 (Amp Assign :
A11:ASSIGN-BiAMP
fig.07b
BiAMP)
fig.08a
8 Front Height
A14:FRONT HEIGHT
fig.08b
1.6. Confirmation items for the video system
See the block diagram fig.XXth.
Paths to be confirmed Display
fig.09
1 Analog Video pass
V01:VIDEO PASS
Video Convert
2 (HDMI ⇒ HDMI) fig.10
V02:V.CONVERT
(Analog ⇒ HDMI)
Settings
Input Source : CBL/SAT
Input Mode : HDMI (fixed)
Sound mode : STEREO
Amp assign : Surround Back
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Analog (fixed)
Sound mode : MULTI CH STEREO
Vol 60dB
Amp assign : Surround Back
Speaker Config ALL Speaker = Small/SW = Yes(2ch)
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Vol 60dB
Amp assign : ZONE2
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : Bi-Amp
MAIN ZONE : ON
ZONE2 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : MULTI CH STEREO
Amp assign : Front Height
MAIN ZONE : ON
ZONE2 : OFF
Settings
Input Source : CBL/SAT
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Video Conversion (IP Scaler) : "Auto", All sources
IP Scaler : "HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : On
ZONE2 : Off
128
What to confirm
・ HDMI input ⇒ Speaker output (Front L/R)
( b The input source can be switched to any source except CBL/SAT.)
・ Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・ Analog input ⇒ Speaker output, SW(20Hz) (Front L/R, Center, Surround L/R, Surround Back L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output (Surround Back L/R → Front L/R)
・ Confirmation of Pre OUT No.
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
・ Analog input ⇒ Speaker output Surround Back L/R (Front Height output)
・ Analog input ⇒ Speaker output Surround Back L/R (Front Height output)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
What to confirm
・ Component input ⇒ Component output (X3300E3 ONLY)
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input ⇒ IP Scaler ⇒ HDMI output.
・ ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
・ CVBS input ⇒ IP Scaler ⇒ HDMI Output
・ Component input ⇒ IP Scaler ⇒ HDMI Output
( b The input source can be switched to any source except CBL/SAT.)