Denon AVR-X3300W Service Manual page 114

SPECIAL MODE
Special mode setting button
b No. 1 - 4, 7 - 10: While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b No. 5 - 6 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds .
b No. 11 : While holding down buttons "A", "B" and "C" simultaneously, insert the AC plug into the wall outlet to turn on the power.
No. Mode
Version Display
1
(u-COM / DSP Error Display)
PANEL / REMOTE LOCK Selection
2
Mode
PANEL LOCK Mode
2-1
(with Volume)
PANEL LOCK Mode
2-2
(without Volume)
2-3 PANEL LOCK mode is turned off
3 Selecting the Mode for Service-related
3-1 Check the Video/Audio path Mode
3-2 Protection history display mode
3-3 232C Standby Clear Mode
3-4 Operation Info Mode
TUNER STEP Mode
3-5
(E3 and E2 model only)
3-6 Remote ID Setup Mode
4 Protection Pass Mode
5 CY920 Reboot Mode
6 CY920 Initialization Mode
7 User Initialization Mode
8 Factory Initialization Mode
9 Clearing the Operation Info
10 USB Update mode
Button A Button B Button C
Displays the version of firmware such as the main firmware or DSP. Errors that have occurred are displayed.
DIMMER STATUS -
(See 1. Version Display
Start this unit in the PANEL/REMOTE LOCK selection mode so that PANEL LOCK and Remote Lock can be switched between On
TUNER
ZONE2
and Off. (See
PRESET CH -
SOURCE
+
PANEL LOCK MODE : No. 2 - 1 - No. 2 - 3
Disables reception from all keys and encoders on the front panel except the power button (including the volume).
↑ ↑ -
Disables reception from all keys and encoders on the front panel except the power button and volume encoder.
↑ ↑ -
Releases the PANEL LOCK.
↑ ↑ -
This is a display for turning on each service-related mode.
ZONE2
DIMMER STATUS
SOURCE Service-related modes: No. 3-1 - No. 3-4 (See
This is a special mode for service confirmation used during repair work to simplify the confirmation work for the Audio channel /
video channel.
↑ ↑ ↑
(See Service Path Check
Displays the protection occurrence history.
↑ ↑ ↑
(See 3-1. Selecting the Mode for
Switches from 232C standby mode to normal standby mode.
↑ ↑ ↑
(See 3-3. 232C Standby Clear
Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
↑ ↑ ↑
rences of each protection. (See
Enables reception STEP of the ANALOG TUNER to be changed.
↑ ↑ ↑
(See 3-5. TUNER STEP mode (E3 / E2
If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur-
↑ ↑ ↑
rently with this device. (See
TUNER
Enables the power to be turned on when protection detection is disabled.
ZONE2
PRESET CH STATUS
SOURCE (See 4. Protection Pass
+
TUNER TUNER
The CY920 is restarted after CY920 hang up.
PRESET CH PRESET CH -
(See 5. CY920 Reboot
+ -
Enter this mode only after replacing Flash for CY920 and rewriting the firmware.
ZONE2
DIMMER -
(See 6. CY920 Initialization
SOURCE
TUNER TUNER
Initializes backup data. (Settings for the Installer Setup are not initialized) (Reboot the CY920)
PRESET CH PRESET CH -
- +
Initializes backup data. (Settings for the Installer Setup are initialized) (CY920 is not Reboot)
ZONE2
DIMMER -
SOURCE (See Initializing This
Clear the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
ZONE2
STATUS -
rences of each protection. (See
SOURCE
TUNER
Switches this unit to USB Update mode.
PRESET CH STATUS -
(See 2. Updating via
+
Mode)
2. PANEL / REMOTE LOCK Selection Mode)
3-1. Selecting the Mode for
Mode)
Service-related)
Mode)
3-4. Operation Info Mode)
only))
3-6. Remote ID Setup Mode)
Mode)
Mode)
Mode)
Unit)
7. Clearing the Operation Info)
USB)
Go to next page.
114
Descriptions
Service-related)