Denon AVR-X3300W Service Manual page 163

Error USB Update Error
Details of Error code
Code Display
Failed to obtain the entire
23 Firmware information after
Update Error**23
SBL Mode.
Time Out while obtaining the
24 entire Firmware information
Update Error**24
after SBL Mode.
25 Update Error**25 Failed to transit to SBL Mode
Time Out in Download (writ-
26 ing to SDRAM) for Firmware
Update Error**26
Download.
Update Error**27 Failed to write to EEPROM
27
after SBL Mode.
36 Update Error**36 Unable to detect USB.
37 Update Error**37 No Firmware File in USB.
The Firmware File in the USB
38 does not support your model
Update Error**38
and area.
39 Update Error**39 Time Out in USB Check.
Update Error**3A Unable to detect USB for
3A
Firmware Download.
Update Error**3B No Firmware File for Firmware
3B
Download.
Error notification received
3C while requesting the Firm-
Update Error**3C
ware Info.
Update Error**3D Time Out while obtaining
3D
Firmware information.
3F Update Error**3F Failed to transit to SBL Mode.
Remedies
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Make sure the model name and area of
the Firmware File, Unplug and recon-
nect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
163
Error USB Update Error
Details of Error code
Code Display
50 Update Error**50 Unable to detect USB.
51 Update Error**51 No Firmware File in USB.
The Firmware File in the USB
52 does not support your model
Update Error**52
and area.
Error notification received
54 while requesting the Firm-
Update Error**54
ware Info.
Update Error**55 Time Out while obtaining
55
Firmware information.
Update Error**56 Unable to detect USB for
56
Firmware Download.
Update Error**57 No Firmware File for Firmware
57
Download.
Invalid Device ID in response
5A or no response from Sub for
Update Error**5A
the "C" command.
NACK received in response or
5B no response from Sub for the
Update Error**5B
"L" command.
Update Error**5C No Update Packet received
5C
from CY920 (Time Out).
Abnormal data in Update
5D Packet received from CY920
Update Error**5D
(CRC Error).
Abnormal data in Update
5E Packet received from CY920
Update Error**5E
(Packet No Error).
Update Error**5F Setup failure of the XModem
5F
transfer method.
Remedies
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Make sure the model name and area of
the Firmware File, Unplug and recon-
nect the AC plug, and try again.
Try a new USB device, Unplug and
reconnect the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
Reinsert or try a new USB device, Un-
plug and reconnect the AC plug, and
try again.
Check the file, Unplug and reconnect
the AC plug, and try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.