ZKTeco SpeedFace-V3L User Manual

Hide thumbs Also See for SpeedFace-V3L:

User manual (93 pages)

Quick start manual (17 pages)

Installation manual (7 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

page of 121

/ 121
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

Product Name and Model Number

User Manual

SpeedFace-V3L

Date: June 2022

Doc Version: 1.0

English

Thank you for choosing our product. Please read the instructions

carefully before operation. Follow these instructions to ensure that the

product is functioning properly. The images shown in this manual are for

illustrative purposes only.

P a g e

| 1

For further details, please visit our Company's website

www.zkteco.com.

U s e r

Table of Contents

Summary of Contents for ZKTeco SpeedFace-V3L

Page 1 Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only. For further details, please visit our Company’s website www.zkteco.com. P a g e Copyright©2020 ZKTECO CO., LTD. All rights reserved.
Page 2 ZKTeco in no event shall be liable to the user or any third party for any incidental, consequential, indirect, special, or exemplary damages, including, without...
Page 3 ZKTeco periodically changes the information herein which will be incorporated into new additions/amendments to the manual. ZKTeco reserves the right to add, delete, amend, or modify the information contained in the manual from time to time in the form of circulars, letters, notes, etc.
Page 4 SpeedFace-V3L User Manual About the Company ZKTeco is one of the world’s largest manufacturer of RFID and Biometric (Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks.
Page 5 The information which is significant. Care taken to avoid danger or mistakes. The statement or event that warns of something or that serves as a cautionary example. P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 6: Table Of Contents
6 USER MANAGEMENT ..................34 ....................34 EGISTRATION 6.1.1 R ..................34 EGISTER A 6.1.2 U ........................35 6.1.3 R ....................36 EGISTER INGERPRINT 6.1.4 F ..........................36 6.1.5 C ..........................37 P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 7 ATE AND .................... 65 CCESS ETTING ....................67 ARAMETERS ......................72 INGERPRINT ...................... 74 ACTORY ESET ....................74 ECURITY ETTINGS 10 PERSONALIZE SETTINGS................77 10.1 ..................... 77 NTERFACE ETTINGS P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 8 ..............110 ERSONNEL ON THE OFTWARE APPENDIX 1 ...................... 111 . 111 EQUIREMENTS OF OLLECTION AND EGISTRATION OF ISIBLE IGHT MAGES ........112 EQUIREMENTS FOR ISIBLE IGHT IGITAL MAGE P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 9 SpeedFace-V3L User Manual APPENDIX 2 ...................... 114 ......................114 RIVACY OLICY ECO-FRIENDLY OPERATION ................118 P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 10: Safety Measures
When cord or connection control is affected.  When the liquid spilled, or an item dropped into the system.  If exposed to water or due to inclement weather (rain, snow, and  P a g e Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 11: Electrical Safety
Make sure that the power has been disconnected before you wire, install,  or dismantle the device. Ensure that the signal connected to the device is a weak-current (switch)  P a g e | 10 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 12: Operation Safety
Clean the device accessories with a piece of soft cloth or a small amount of cleaning agent. If you have any technical questions regarding usage, contact certified or  P a g e | 11 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 13 The warranty service does not cover accidental damage, damage caused  by mis-operation, and damage due to independent installation or repair of the product by the user. P a g e | 12 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 14: Instruction For Use
Our company will assume no liability for recognition issues that may result from incorrect usage of the product. We reserve the right of final interpretation and modification concerning this point. P a g e | 13 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 15: Standing Position , Facial Expression And Standing Posture
Recommended standing posture and facial expression  Facial Expression Standing Posture Note: Please keep your facial expression and standing posture natural while enrolment or verification. P a g e | 14 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 16: Face Registration
If you do not follow the instructions on the screen, the face  registration may take longer or may fail. Be careful not to cover the eyes or eyebrows.  P a g e | 15 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 17: Standby Interface
Do not cover the face, allow the device to recognize both the eyebrows and the face. Standby Interface After connecting the power supply, the following standby interface is displayed: P a g e | 16 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 18 When there is no Super Administrator set in the device, tap to go to  the menu. After adding a Super Administrator on the device, it requires the Super  Administrator’s verification before opening the menu functions. P a g e | 17 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 19 Note: The punch state options are off by default and need to select other mode options in the "Punch State Option" to get the punch state options on the standby screen. P a g e | 18 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 20: Virtual Keyboard
Press [123] to switch to the symbolic keyboard.  Tap [@#&] to return to the English keyboard.  Tap [ ] to exit the virtual keyboard.  P a g e | 19 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 21: Verification Mode
1:1 Fingerprint Verification Mode  Compares the fingerprint that is being pressed onto the fingerprint reader with the fingerprints that are linked to User ID input via the virtual keyboard. P a g e | 20 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 22 If an employee registers a face, password and card in addition to the fingerprint, the following screen will appear. Select the icon to enter fingerprint verification mode. P a g e | 21 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 24: Facial Verification
Compare the face captured by the camera with the facial template related to the entered user ID. Press on the main interface and enter the 1:1 facial verification mode. Enter the user ID and click [OK]. P a g e | 23 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 25 If an employee registers a fingerprint, password and card in addition to the face, the following screen will appear. Select the icon to enter face verification mode. P a g e | 24 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 26: Card Verification
The 1: N Card Verification mode compares the card number in the card induction area with all the card number data registered in the device; The following is the card verification screen. P a g e | 25 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 27 User ID registered in the device. Press on the main interface and enter the 1:1 card verification mode. Enter the user ID and click [OK]. P a g e | 26 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 28 If an employee registers a fingerprint, face and password in addition to the card, the following screen will appear. Select the icon to enter card verification mode. P a g e | 27 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 29: Password Verification
If an employee registers a fingerprint, face and card in addition to the password, the following screen will appear. Select the icon to enter password verification mode. P a g e | 28 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 30 SpeedFace-V3L User Manual Input the password and press [OK]. Below are the display screens after entering a correct password and a wrong password, respectively. P a g e | 29 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 31: Combined Verification
Personnel ID in the Device. This method compares the entered verification of a person with all the verification templates previously stored to that Personnel ID in the Device. P a g e | 30 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 32 Password) previously stored to that Personnel ID in the Device. But as the employee has registered only the Face but not the Password,  the verification will not get completed and the Device displays “Verification Failed”. P a g e | 31 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 34 LCD Screen, Audio, Microphone, Fingerprint sensor, Camera, and Real-Time Clock. To view Privacy Policy, Data Capacity and Device and System Info Firmware information of the current device. P a g e | 33 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 35: User Management
User Management User Registration Tap User Mgt. on the main menu. 6.1.1 Register a User ID and Name Tap New User and enter the User ID and Name. P a g e | 34 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 36: User Role
Note: If the selected user role is the Super Admin, then the user must pass the identity authentication to access the main menu. The authentication is based P a g e | 35 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 38: Card
The registration of the card will be successful. If the card has already been registered, the message "Error! Card  already enrolled" appears. The registration interface looks like this: P a g e | 37 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 39: Password
"Password does not match!", where the user needs to re-confirm the password again. The password may contain 6 to 8 digits by default.  P a g e | 38 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 40: Access Control Role
When press the finger corresponding to the duress fingerprint on the sensor and pass the verification, the system will immediately generate a duress alarm. P a g e | 39 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 41: Search User
(where the keyword may be the user ID, surname, or full name) and the system will search for the related user information. P a g e | 40 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 42: Edit User
SpeedFace-V3L User Manual Edit User On the All-Users interface, tap on the required user from the list and tap Edit to edit the user information. P a g e | 41 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 43: Delete User
Delete Face Only: Deletes the face information of the selected user.  Delete Password Only: Deletes the password information of the  selected user. Delete Card Number Only: Deletes the card information of the selected  user. P a g e | 42 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 44: Display Style
SpeedFace-V3L User Manual Display Style On the Main Menu, tap User Mgt., and then tap Display Style to enter Display Style setting interface. P a g e | 43 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 46: User Role
On the User Defined Role interface, toggle Enable Defined Role to  enable or disable the user defined role. Tap on Name and enter the custom name of the role.  P a g e | 45 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 48 User Role to assign the created roles to the required users. But if there is no super administrator registered in the Device, then the device will prompt "Please enroll super admin first!" when enabling the User Role function. P a g e | 47 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 49: Communication Settings
PC connect to the same network segment. Tap Ethernet on the Comm. Settings interface to configure the settings. P a g e | 48 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 50 The default TCP COMM Port value is 4370. It can be TCP COMM. Port modified according to the network availability. Dynamic Host Configuration Protocol dynamically DHCP allocates IP addresses for clients via server. P a g e | 49 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 51: Serial Comm
RS485(PC): Communicate with the device through the Serial Port RS485 serial port. Master Unit: When RS485 is used as the function of "Master unit", it can be connected to a card reader. P a g e | 50 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 52: Pc Connection
It is the identification number of the device, which ranges between 1 and 254. Baud Rate If the communication method is RS485, you need to input this device ID in the software communication interface. P a g e | 51 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 53: Wi-Fi Settings
Tap on the required Wi-Fi name from the available list and input the  correct password in the password interface, and then tap Connect to Wi-Fi (OK). P a g e | 52 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 54 When the WIFI is connected successfully, the initial interface will display  the Wi-Fi logo. Adding Wi-Fi Network Manually  The Wi-Fi can also be added manually if the required Wi-Fi does not show on the list. P a g e | 53 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 55 Note: After successfully adding the WIFI manually, follow the same process to search for the added Wi-Fi name. Advanced Setting  On the Wi-Fi Settings interface, tap on Advanced to set the relevant parameters as required. P a g e | 54 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 56 Subnet Mask 255.255.255.0. It can be modified according to the network availability. The Default Gateway address is 0.0.0.0. It can be Gateway modified according to the network availability. P a g e | 55 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 57: Cloud Server Setting
Port used by the ADMS server. The IP address and the port number of Enable Proxy Server the proxy server is set manually when the proxy is enabled. P a g e | 56 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 58: Wiegand Setup
It is used to set the Wiegand input and output parameters. Tap Wiegand Setup on the Comm. Settings interface to set up the Wiegand input and output parameters. 8.6.1 Wiegand Input P a g e | 57 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 62: Wiegand Output
Its value can be 26 bits, 34 bits, 36 bits, 37 bits, Wiegand Format and 50 bits. After selecting the required Wiegand format, Wiegand Output Bits select the corresponding output bit digits from the Wiegand format. P a g e | 61 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 63: Network Diagnosis
Tap Network Diagnosis on the Comm. Settings interface. Enter the IP address that needs to be diagnosed and tap Start the Diagnostic Test to check whether the network can connect to the device. P a g e | 62 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 64: System Settings
Tap System on the Main Menu interface to get into its menu options. Date and Time Tap Date Time on the System interface to set the date and time. P a g e | 63 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 65 Tap Daylight Saving Time to enable or disable the function. If enabled,  tap Daylight Saving Mode to select a daylight-saving mode and then tap Daylight Saving Setup to set the switch time. P a g e | 64 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 66: Access Logs Setting
18:30 on January 1, 2021. After restoring the factory settings, the time of the device will remain at 18:30 on January 1, 2021. Access Logs Setting Tap Access Logs Settings on the System interface. P a g e | 65 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 68: Face Parameters
5 seconds. Valid value: 0 to 9 seconds. 0 means continuous identifying, 1 to 9 means identifying at intervals. Face Parameters Tap Face on the System interface to go to the Face parameter settings. P a g e | 67 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 69 The valid value ranges from 0 to 100. The higher the thresholds, the lower the misjudgement rate and the higher the rejection rate, and vice versa. It is recommended to set the default value of 47. P a g e | 68 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 70 If a face’s pitch angle exceeds the set value, it will Face Pitch Angle be filtered by the algorithm, i.e., ignored by the terminal thus no registration and comparison interface will be triggered. P a g e | 69 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 71 This value controls the turning on and off of the LED Light Trigger LED light. The larger the value, the LED light will Threshold turn on or off more frequently. P a g e | 70 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 72 It has facial algorithm related information and Face algorithm pause the facial template update. After disable this function, face re-registration is Save Photo as Template required after an algorithm upgrade. P a g e | 71 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 73: Fingerprint
1:1 Threshold Value between the acquired fingerprint data and the fingerprint template associated with the entered user ID enrolled in the device is greater than the set value. P a g e | 72 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 74 Show for Match: to display the fingerprint image on the screen only during verification. Always Show: to display the fingerprint image on screen during enrollment and verification. None: not to display the fingerprint image. P a g e | 73 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 75: Factory Reset
Tap Reset on the System interface and then tap OK to restore the default factory settings. Security Settings Tap Security Settings on the System interface to go to the Security settings. P a g e | 74 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 76 C/S software (such Communication as ZKAccess 3.5) on your computer in advance for offline use. SSH is used to enter the background of the device for maintenance. P a g e | 75 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 77 Set whether to display the username in the Name verification result interface. Display Verification Set whether to display the verification mode in Mode the verification result interface. P a g e | 76 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 78: Personalize Settings
10.1 Interface Settings Tap User Interface on the Personalize interface to customize the display style of the main interface. P a g e | 77 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 79 Idle Time to Slide Show exceeds the set value, a slide show is displayed. The function can be disabled, or you may set the value between 3 and 999 seconds. P a g e | 78 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 80: Voice Settings
The style of the main screen can be selected Main Screen Style according to the user preference. 10.2 Voice Settings Tap Voice on the Personalize interface to configure the voice settings. P a g e | 79 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 81: Bell Schedules
Tap Bell Schedules on the Personalize interface to configure the Bell settings. New Bell Schedule  Tap New Bell Schedule on the Bell Schedule interface to add a new bell schedule. P a g e | 80 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 82 Repeat scheduled bell. Ring Tone Select a ringtone. Set the replay time of the internal bell. Valid Internal Bell Delay(s) values range from 1 to 999 seconds. P a g e | 81 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 83: Punch States Options
Yes to delete the selected bell. 10.4 Punch States Options Tap Punch States Options on the Personalize interface to configure the punch state settings. P a g e | 82 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 85: Shortcut Key Mappings
If the Shortcut key is defined as a function key (such as New user, All users,  etc.), the configuration is completed as shown in the image below. P a g e | 84 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 86 On the Shortcut Key interface, tap Set Switch Time to set the switch  time. On the Switch Cycle interface, select the switch cycle (Monday, Tuesday,  etc.) as shown in the image below. P a g e | 85 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 87 User Manual Once the Switch cycle is selected, set the switch time for each day, and  tap OK to confirm, as shown in the image below. P a g e | 86 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 89: Data Management
Tap Delete Data on the Data Mgt. interface to delete the required data. Function Description Function Name Description Delete Access Records To delete the access records conditionally. P a g e | 88 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 91: Access Control
In default settings, new users are allocated into the first group with the default group time zone, where the access combo is "1" and is set in unlock state by default. P a g e | 90 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 92: Access Control Options
Lock Delay, Door Sensor Delay, and Door Sensor Type options. The length of time that the device controls the electric lock to be in unlock state. Door Lock Delay (s) Valid value: 1~99 seconds. P a g e | 91 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 93 Face + Fingerprint + Card, Face + Fingerprint + Password. Door Available Time It sets the timing for the door so that the door is Period accessible only during that period. P a g e | 92 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 94 It transmits a sound alarm or disassembly alarm from the local. When the door is closed or the Speaker Alarm verification is successful, the system cancels the alarm from the local. P a g e | 93 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 95: Time Schedule
24-hour clock. Tap the grey box to search the required Time Zone and specify the required Time Zone number (maximum up to 50 zones). P a g e | 94 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 96 On the selected Time Zone number interface, tap on the required day (that is Monday, Tuesday, etc.) to set the time. Specify the start and the end time, and then tap OK. P a g e | 95 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 98: Combined Verification
In a door-unlocking combination, the range of the combined number N is 0 ≤ N ≤ 5 and the number of members N may all belong to one access group or may P a g e | 97 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 99 AC Group 2, the next two are from AC Group 4, and the last person is from AC Group 7. If the Door-unlock combination 3 is set as (09 09 09 09 09). It indicates  P a g e | 98 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 100: Anti-Passback Setup
Wiegand signal. The Wiegand format and Output type (User ID/Card Number) adopted by the master device and slave device must be consistent. P a g e | 99 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 101 In Anti-Passback: The user can check-in again only if the last record is a check-out record otherwise an alarm is raised. However, the user can check-out freely. P a g e | 100 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 102: Duress Options Settings
At the same time, a signal is sent to trigger the alarm as well. On the Access Control interface, tap Duress Options to configure the duress settings. P a g e | 101 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 103 1 to 999 seconds. Set the 6-digit duress password. When the user Duress Password enters this duress password for verification, an alarm signal will be generated. P a g e | 102 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 104: Attendance Search
OK. If you which the records need want to search for records of all to be searched. users, tap OK without entering any user ID. P a g e | 103 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 105 SpeedFace-V3L User Manual Once record search The figure shows the details of completes. Tap the record the selected record. highlighted in green to view its details. P a g e | 104 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 106: Autotest
To automatically test the display effect of LCD screen by displaying full-color, pure white, and Test LCD pure black to check whether the screen displays colors normally. P a g e | 105 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 107 To test the RTC. The device tests whether the clock works normally and accurately with a Test Clock RTC stopwatch. Touch the screen to start counting and press it again to stop counting. P a g e | 106 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 108: System Information
Version, Manufacturer, and manufacture date. Displays the firmware version and other version Firmware Info information of the device. Privacy Policy Display the device's privacy policy. P a g e | 107 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 109: Connect To Zkbioaccess Software
Server address: Set the IP address as of ZKBio Access server. Server port: Set the server port as of ZKBio Access(The default is 8088). P a g e | 108 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 110: Add Device On The Software
Click Access Control > Device > Search Device, to open the Search interface in the software. Click Search, and it will prompt [Searching……]. After searching, the list and total number of access controllers will be displayed. P a g e | 109 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 111: Add Personnel On The Software
Fill in all the required fields and click [OK] to register a new user. Click Access > Device > Device Control > Synchronize All Data to Devices to synchronize all the data to the device including the new users. P a g e | 110 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 112: Requirements Of Live Collection And Registration Of Visible Light Face Images
Do not include more than one face in the capturing area. A distance of 50cm to 80cm is recommended for capturing the image. (the distance is adjustable, subject to body height). P a g e | 111 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 113: Requirements For Visible Light Digital Face Image Data
A neutral face or smile with eyes naturally open are recommended.  Gesture and Angel The horizontal rotating angle should not exceed ±10°, elevation should not exceed ±10°, and depression angle should not exceed ±10°. P a g e | 112 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 114 The captured person should be easily visible, natural in color, no harsh shadow or light spot or reflection in the face or background. The contrast and lightness level should be appropriate. P a g e | 113 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 115 Appendix 2 Privacy Policy Notice: To help you better use the products and services of ZKTeco and its affiliates, hereinafter referred as "we", "our", or "us", the smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
Page 116 Only your user ID is displayed by default. You can set whether to display other user verification information (such as Name, Department, Photo, etc.) under the Administrator privilege. If you choose to display such P a g e | 115 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 117 Policy carefully, and only use our services or information provided by us with consent of your parents or guardian. We will only use or disclose personal information of minors collected with P a g e | 116 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 120 Note: 80% of this product’s components are manufactured using non-toxic and eco-friendly materials. The components which contain toxins or harmful elements are included due to the current economic or technical limitations which prevent their replacement with non-toxic materials or elements. P a g e | 119 Copyright©2022 ZKTECO CO., LTD. All rights reserved.
Page 121 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone: +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright © 2022 ZKTECO CO., LTD. All Rights reserved. P a g e | 21 Copyright©2020 ZKTECO CO., LTD. All rights reserved.

ZKTeco SpeedFace-V3L User Manual

Quick Links

Related Manuals for ZKTeco SpeedFace-V3L

Summary of Contents for ZKTeco SpeedFace-V3L

Table of Contents