Page 1
Quick Start Guide SpeedFace - V5L[TI] Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
Page 2
Overview Thermal Imaging Temperature Detection Module Flash Camera & Palm Collector Microphone 5" touchscreen Fingerprint Sensor Magnetic Tamper Switch Reset Speaker Auxiliary input Power in RXD2 Sensor TXD2 RS232 Ethernet Exit Button +12V IWD0 RS232 Lock Wiegand IWD1 485A Wiegand RS485 Alarm 485B...
Installation Environment Please refer to the following recommendations for installation. INSTALL INDOORS AVOID INSTALLATION AVOID DIRECT AVOID USE OF ANY ONLY NEAR SUNLIGHT HEAT SOURCE GLASS WINDOWS AND EXPOSURE NEAR THE DEVICE Recommended Palm Gestures KEEP EFFECTIVE KEEP SPACES DO NOT KEEP DO NOT KEEP DO NOT KEEP DISTANCE OF...
Installation Requirements The installation requirements and indications associated with the device are given below: Specification Standard value Remark Indoor, Avoid wind, Avoid The recommended operating Operating direct sunlight, temperature is 25°C (77°F) Environment 16°C to 35°C (60.8°F to 95°F) Distance The recommended distance 30 to 120cm (0.98ft to 3.94ft) (between face...
Device Installation ① 1.5m ② Attach the mounting template sticker to the wall, and drill holes according to the ① mounting paper. Fix the back plate on the wall using wall mounting screws. ② Attach the device to the back plate. ③...
Power Connection 12V DC Recommended power supply 1) 12V ± 10%, at least 3000mA. 2) To share the power with other devices, use a power supply with higher current ratings. Ethernet Connection RJ 45 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 Click [COMM.] >...
Door Sensor, Exit Button & Alarm Connection Smoke Detector Door Sensor ExitButton Alarm's power switch Alarm Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (normally opened when powered) is connected with 'NO1' and 'COM' terminals, and the NC Lock (normally closed when powered) is connected with 'NC1' and 'COM' terminals.
Page 8
Wiegand Reader Connection Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last two pins are used by the Access controller, as shown in the following figure. It sends the credentials to the device via wiegand communication. +12V IWD0 IWD1...
User Registration When there is no super administrator set in the device, click on to enter the menu. Add a new user and set User Role to Super Admin, then the system will request for the administrator’s verification before entering the menu. It is recommended to register a super administrator initially for security purposes.
Page 10
Method 2: Register on ZKBioAccess MTD software Please set the IP address and cloud service server address in the Comm. Menu option on the device. 1. Click [Access] > [Access Device] > [Device] > [Search Device] to search the device on the software.
Page 11
Method 3: Register on the phone Once the ZKBioAccess MTD software is installed, the users could enroll their face via a browser application on their own mobile phone. 1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code UGL bar.
Page 12
Ethernet and Cloud Server Settings Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click on >...
Access Control Setting Click on > [Access Control] to enter the access control management interface and set relevant parameters of access control. Main Menu Access Control Options Access Control Access Control Options Gate Control Mode User Mgt. System User Role COMM.
Page 14
Detection Management Settings Click on > [ System ] > [ Detection Management ] to enter the setting interface ❶ You can set the value of High temperature alarm threshold, and enable the Temperature over the range; access denied and the Trigger external alarm, the device will send an alarm prompt when the temperature of the user detected exceeds this value, meanwhile the user will be forbidden to access, as shown in the following figure.
Page 15
Notes: The effective distance for temperature detection is within 50cm. Recommended for indoor use. Temperature measurement data is for reference only, not for medical use. Remove the mask to register the face, wear a mask to recognize the face, the type of mask, the size of the face covered by the mask, and bangs will affect the facial recog- nition effect.
Real-Time Monitoring Welcome, admin 2020-05-22 11:03:07 Real-Time Monitoring Temperature Management Total: Real-Time Monitoring Normal Records Abnormal Temperature Statistics Panel Temperature Raw Record Name: UnregisterUser Personnel Temperature Schedule Department: NULL Temperature: 36.57℃ Abnormal Temperature Record 52.1 C Mask: Departmental body temperature Mask: None daily statistics report...