Toshiba ESTIA R32 HWT-401HW-E Manual page 57

Room temperature control with second
remote control:
0 = Invalid; 1 = Valid
Cooling room temperature, upper limit
Cooling room temperature, lower limit
Heating room temperature, upper limit
Heating room temperature, lower limit
Start temperature in cooling mode, either with
room temperature sensor on the remote control or
external room temperature sensor
Room temperature
control with second
Start temperature in heating mode, either with
wired remote control or
room temperature sensor on the remote control or
external room thermostat
external room temperature sensor
HiPower restarts water temperature in Zone A.
(Only valid with room temperature control by
means of 2nd remote control)
Start temperature in heating mode, control setting
by means of room temperature remote control or
room temperature thermostat
Room temperature compensation:
Heating: Room temperature compensation value
(sensor temperature control temperature, K)
Room temperature compensation:
Cooling: Room temperature compensation value
(sensor temperature control temperature, K)
2-way valve operation Reversal of the switching logic for the
output (cooling mode) 2-way cooling stop valve
Control of the hydraulic Reversal of the switching logic for the 3-way
3-way control valve changeover valve / domestic hot water
3-way mixing valve runtime (x 10 sec.)
Mixing valve runtimes,
2 zones
Actuation of 3-way mixing valve (min.)
Temperature difference for changing the opening
value of the mixing valve
Maximum stages of the mixing valve
External heating/heat pump
synchronization
0 = Synchronized
1 = Not synchronized
0 = HP + hot water generation
Boiler/heat pump
1 = Hot water generation only
synchronization
2 = E-heating element function only up to 60 min.
3 = HP + circulation pump STOP
Activate / deactivate error code A02 (high water
return control):
0 = A02 activated
1 = A02 deactivated
0 = Cooling & heating
Cooling mode
1 = Heating operation only
24 h or 12 h time display
Remote control display
0 = 24 h; 1 = 12 h
Low-noise night mode
0 = Invalid; 1 = Valid
Low-noise night mode Start time
End time
Storage location
Function code
FC description HB*
40
92
93
94
95
96
9D
B2
B5
-
-
3C
54
0C
59
6F1
6F2
3E
5B
62
02
-
-
-
-
no .
RC* Range Preset
- 0~1
- 15~30 29
- 15~30 18
- 15~30 29
- 15~30 18
- 10~25 20
20~55 401/ 601
- 40
65 801/1101
- 20~37 25
- 0~1
02 -10~10
03 -10~10
- 0~1
0~1
- 3~24
- 1~30
- 1~3
- 12~60 24
- 0~1
- 0~3
- 0~1
- 0~1
05 0~1
09 0~1
0A 0~23 22
0B 0~23
*HB= Hydrobox EEPROM
*RC= Remote Control
Additional info
Second remote control, target temperature setting
0 0 = Water temperature
1 = Room temperature (sensor on remote control)
Settings on the remote control
Supply water temperature at which the heat pump
starts; =20°C If the set temperature set on
the external room thermostat or on the second
remote control is not reached, the supply water
temp. is lowered by 1°C every 1/2 h until the limit
temperature (FC 19) or set temperature is reached
Supply water temperature at which the heat pump
starts; =40°C If the set temperature set on the
external room thermostat or on the second remote
control is not reached (room sensor), the supply
water temp. is increased by 1°C every 1/2 h until
the limit temperature (FC 1A) or set temperature is
reached
A Zone = Thermo off; but if TWi < 25°C
heat pump restarts to prevent underfloor heating
from cooling
0 = Fixed value as per FC 9D
0
1 = Calculated value based on auto curve
Adjusts the measured difference between the room
-1 temperature sensor on the remote control and the
actual room temperature
Adjusts the measured difference between the room
-1 temperature sensor on the remote control and the
actual room temperature
0 = Output assigned 230 V for cooling
1 = Output voltage-free during cooling
0 = Voltage during hot water preparation
0
1 = Voltage-free during hot water preparation
Runtime of the valve motor between fully open
and closed, different depending on make. Must be
6 set prior to commissioning! Only use valves with
10-second increments
e.g., 90 sec., 100 sec., etc. (range 30 - 240 sec.)
Interval at which the valve readjusts
2
(Recommendation: 1 min.)
2
0
3
0
0 For activating cooling mode
Defines whether 24-hour or 12-hour format should
0
be displayed on the remote control
0
Restricts the maximum output of the HP to 75%,
thereby achieving a noise reduction
6
TOSHIBA I 17 I 17
TOSHIBA