Alliance Laundry Systems AE Series Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Dryer
  5. AE Series
  6. Manual
Alliance Laundry Systems AE Series Manual

Alliance Laundry Systems AE Series Manual

Home laundry dryers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Home Laundry
Dryers
"AE", "AG", "AEE", "AGE", "AEM",
"AGM", "NE and "NG" Series
Refer to Page 6 for Model Numbers
Part No. 62310R1
www.comlaundry.com
February 2002

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AE Series and is the answer not in the manual?

Questions and answers

Related Manuals for Alliance Laundry Systems AE Series

Summary of Contents for Alliance Laundry Systems AE Series

  • Page 1 Home Laundry Dryers “AE”, “AG”, “AEE”, “AGE”, “AEM”, “AGM”, “NE and "NG" Series Refer to Page 6 for Model Numbers Part No. 62310R1 www.comlaundry.com February 2002...

  • Page 2: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 3 84. Symptom: Improper Heat Or Drying Times ..84 85. Symptom: “oP” appears in Time display ..85 86. Symptom: “SH” appears in time Display ..86 87. Control Replacement ........87 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 4: Section 1 - Safety Information

    • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R1 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 5: Locating An Authorized Servicer

    Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.

  • Page 6: Section 2 - Introduction

    Nameplate Location When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on nameplate(s) as shown. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 7: Model Identification

    AG9439 AG4419 AGM639 NE8833 AE3413 AEM453 NG8839 AG3419 AGM459 NE6813 AEE953 AEM433 NG6819 AGE959 AGM439 AE5413 AEE933 AEM353 AG5419 AGE939 AGM359 NE4813 AEM653 AEM333 NG4819 AGM659 AGM339 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 8: How Your Dryer Works

    The heated air moves through the heater duct and into the cylinder, where it circulates through the wet load. The air then passes through the lint filter, air duct, and exhaust fan, where it is vented to the outdoors. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 9: Section 3 - Troubleshooting

    †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models only. † Electronic Control Models only. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 10: Motor Overload Protector Cycles Repeatedly

    • Test timer and replace if inoperative. †Inoperative electronic control. • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models only. † Electronic Control Models only. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 11: Heater Assembly Does Not Heat Or Burner Does Not Ignite

    • Thermistor is open, replace thermistor. Broken, loose, or incorrect wiring. • Refer to appropriate wiring diagram. * Mechanical Timer Models only. † Electronic Control Models only. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 12: Igniter Does Not Glow (Gas Supply Sufficient) - Gas Models

    Sensor installed improperly on burner housing. • Loosen screw and properly position the sensor on the burner housing. * Mechanical Timer Models only. † Electronic Control Models only. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 13: Heater Assembly Or Burner Shuts Off Prematurely

    • Test thermistor and replace if inoperative. Air leak at blower seal. • Check and replace seal if necessary. * Mechanical Timer Models only. † Electronic Control Models only. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 14: Heater Assembly Or Burner Does Not Shut Off

    Gas Models: Gas line pressure too high or too low. • If Natural Gas line pressure to dryer exceeds 8 inch water column pressure, or is lower than 4 inch water column, ask Gas Company to correct. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 15: Timer Does Not Advance In Automatic Cycle (Mechanical Timer Models Only)

    • Test timer and replace if inoperative. Improper or inadequate exhaust system. • Refer to Installation Instructions (supplied with dryer) for exhaust requirements. * Mechanical Timer Models only. † Electronic Control Models only. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 16: Motor Mounting Bracket To Motor

    Refer to Figure 1 FROM TERMINAL BRACKET TO CONTROL HOUSING (Electric Models Only) Refer to Figure 2 GROUND WIRE DRY832S GROUND WIRE Figure 1 DRY1051S Figure 2 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 17: Power Cord To Terminal Block Bracket And From Terminal Block Bracket To Control Housing. Wall Receptacle Polarity Check (Gas Models Only)

    Refer to Figure 3 NOTE: For determining GROUND the correct polarity of a WIRE wall receptacle. GROUND NEUTRAL NEUTRAL SIDE GROUND WIRE V.A.C. V.A.C. V.A.C. DRY1052S Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 18: From Terminal Block Bracket To Timer Mounting Bracket To Dryer Cabinet Top

    BRACKET TO GRAPHICS PANEL (Electronic Control Models Dryers) (Mechanical Timer Models Dryers) Refer toFigure 4 Refer to Figure 4 GROUND WIRES GROUND WIRES DRY1054S DRY1053S MECHANICAL ELECTRONIC Figure 4 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 19: Section 5 - Service Procedures

    ELECTRONIC CONTROL END CAP (Right) GRAPHICS PANEL SCREW DRY1071S GRAPHICS PANEL, CONTROL HOOD AND CONTROLS (Models AG9439, AE9433, NG8839, NE8833, AGE959, AEE953, AGE939 and AEE933) Figure 5 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 20 END CAP (Right) SCREW CLIP TRIM STRIP TIMER DRY1072S KNOB CONTROL KNOB ASSEMBLY GRAPHICS PANEL, CONTROL HOOD AND CONTROLS (Models AGM659, AEM653, AGM639 and AEM633) Figure 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 21 TIMER END CAP (Right) CLIP SCREW DRY1073S TIMER KNOB ASSEMBLY CONTROL KNOB ASSEMBLY GRAPHICS PANEL, CONTROL HOOD AND CONTROLS (Models NG6819, NE6813, AG5419 and AE5413) Figure 7 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 22 STRIP TIMER KNOB SCREW ASSEMBLY CLIP CONTROL KNOB ASSEMBLY GRAPHICS PANEL, CONTROL HOOD AD CONTROLS (Models NG4819, NE4813, AG4419, AE4413, AGM459, AEM453, AGM439 and AEM433) Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 23 TIMER GRAPHICS END CAP PANEL (Right) TIMER KNOB ASSEMBLY SCREW DRY1075S GRAPHICS PANEL, CONTROL HOOD AND CONTROLS (Models AG3419, AE3413, AGM359, AEM353, AGM339 and AEM333) Figure 9 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 24: Temperature Switch

    Meter should rear d. Carefully remove the graphics panel off the approximately 1,000 Ohms at all times. front of the control hood. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 25: Lint Filter

    “Front” facing the front of the dryer. 28. LOADING DOOR Remove four screws holding hinges to door. Refer to Figure 10. HINGE SCREWS DRY1055S LINT FILTER FRONT AIR DUCT Figure 10 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 26: Inner And Outer Door Panels And Door Handle

    HEX HEAD STRIKER SCREW DOOR SEAL INNER DOOR PANEL DOOR DOOR ASSEMBLY HANDLE SPEED PHILLIPS HEAD SCREW OUTER DOOR PANEL PHILLIPS HEAD DOOR SCREW HINGE DRY850S Figure 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 27: Front Panel And Panel Seal

    HOLD-DOWN DOOR CLIP FRONT DOOR SWITCH GUIDE PANEL SEAL SWITCH TABS STRIKER LOCKNUT CATCH DRY1056S SCREW ACCESS Figure 13 DOOR DRY1057P SCREW DOOR HINGE Figure 12 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 28: Striker Catch

    Remove four screws and locknuts holding secondary valve coil, opening the valve and hinges to front panel. Refer to Figure 12. allowing gas to flow. Ignition is made and the © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 29: Ignition System Features (Gas Models)

    In case of flame failure, the sensor contacts will reclose in about 45 seconds. This will close the secondary valve and the burner system will be in the normal pre-ignition circuit. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 30 Fabric settings, except FLUFF which should read “zero” VAC. 4. If meter does not read line voltage in step “3”, check motor switch, thermostat, thermistor, temperature switch or timer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 31: Burner System Components - Gas Models

    Refer to Figure 17. mounting bracket to base. Refer to Figure 14. (7) Lift gas valve and mounting bracket from base. Refer to Figure 14. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 32 NOTE: Test procedure can be performed on workbench if gas valve, igniter, burner tube and burner housing have been removed from dryer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 33: Burner Housing And Heat Shroud

    Remove two screws holding shroud to heater housing, holding burner tube in place. Refer to box and remove shroud out through front of Figure 14. dryer. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 34: Limit Thermostat

    While thermostat is still hot, apply meter probes to thermostat terminals 1 and 2; meter should read “infinite” until thermostat cools at which time the meter should read “zero.” © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 35: Heater Assembly

    ASSEMBLY LOCKSCREW TUBE THERMOSTAT THERMOSTAT GAS VALVE HANDLE BURNER TUBE SCREW D244S BASE BURNER D243S HOUSING HEATER THERMAL SHUTTER ATTACHING FUSE HEX HEAD SCREW SCREW Figure 19 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 36: Thermistor Or Thermostat Or Thermostat And Heater

    2. Set meter to read Ohms. Apply meter probes to the heater assembly terminals. Meter should DRY1058S read 10.4 Ohms ± .30 Ohms cold. Figure 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 37: Front Air Duct

    Refer to Figure 12. c. Disconnect wires from door switch. Refer to CABINET ATTACHING SCREWS Figure 13. NOTE: Refer to the appropriate wiring diagram Figure 21 when rewiring the switch. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 38 LEVER D248S IMPORTANT: When reinstalling motor and exhaust assembly, be sure wire harness on right side is clipped to motor mounting bracket and is routed Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 39 4. Put test meter probes on terminal 4 and motor “zero” Ohms. frame. Meter should register “no reading” or infinite. DRY956S Figure 25 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 40 Figure 26. EXHAUST HOUSING ATTACHING SCREWS (3) Pry two motor clamps off using a screwdriver. Refer to Figure 26. Then lift Figure 27 motor out of mounting bracket. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 41: Cylinder Light

    NOTE: Refer to the appropriate wiring diagram when rewiring the switch. d. Disconnect wires from the light receptacle terminals. e. Remove two screws holding receptacle to front bulkhead. Refer to Figure 28. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 42: Front Bulkhead Assembly

    (1) Remove two screws holding glide to each when rewiring the switch. glide bracket. d. Disengage belt from motor and idler pulleys. h. Front Cylinder Seal (Refer to Figure 31) Refer to Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 43: Cylinder Belt

    Seal must be held securely under strap and folded under flanged edge around entire bulkhead. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 44: Cylinder Assembly

    NOTE: The cylinder must be installed with the DRY954S arrow pointing toward the front of the dryer. ELONGATED BAFFLE Figure 32 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 45: Rear Seal

    Manually rotate cylinder until one of the baffles is at the 6 o’clock position and carefully remove cylinder out through front of dryer. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 46: Rear Bulkhead And Heater Box Assemblies

    ROLLER RING i. To remove roller shaft, remove two screws holding roller bracket to rear bulkhead, then remove locknut holding shaft to bracket. Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 47 (5) Move air shutter end of burner tube slightly NOTE: Refer to the appropriate wiring diagram to right and CAREFULLY remove burner when rewiring the switch. tube and igniter assembly out through front of dryer. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 48: Terminal Block Or Power Cord

    (4) Remove two cabinet hold-down screws. Refer to Figure 30. (5) Raise front of cabinet top hinging on rear hold-down brackets. Refer to Figure 36. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 49: Cabinet

    Power Cord – Gas Models (1) Remove access plate on rear of cabinet. (2) Remove strain relief. (3) Remove screw holding power cord ground wire to terminal block bracket. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 50 (5) Move air shutter end of burner tube slightly to right and CAREFULLY remove burner tube and igniter assembly out through front of dryer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 51: Base

    Refer to Figure 19. (9) Remove four screws holding shroud to heater box and remove shroud and burner housing out through front of dryer. Refer to Figure 18. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 52 Refer to Figure 30. Then remove remaining screws from around bottom of cabinet and lift cabinet off base. o. Remove leveling legs and locknuts from base and reinstall on new base. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 53: Section 6 - Adjustments

    NOTE: If these locknuts are not tight, the dryer will not stay level during operation. DRY868S LOCKNUT LEVELING RUBBER Figure 37 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 54: Burner Flame (Gas Models)

    D399S access door. f. Reinstall the access door. SHUTTER WARNING For personal safety, the access door must be in place during normal operation. Figure 38 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 55: Section 7 - Gas Burner Conversion Procedures

    Remove pressure tap pipe plug and check gas pressure by connecting a “U ” tube manometer (or similar pressure gauge) to the pressure tap . Refer to Figure 39. DRY961S PRESSURE Figure 39 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 56: Installing The No. 401P3 Kit

    (3) Start dryer, pressure should be 10 ± 1.5 the closed position. Refer to Figure 41. inches (25.4, ± 3.8 cm). Refer to Figure 41. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 57 A a soapy solution. harsh, roaring, very blue flame indicates too much air.) Adjust air shutter to obtain a soft uniform blue flame as follows: 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 58 Reinstall the access door and screw. WARNING For personal safety, access door must be in place during normal operation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 59 Remove pressure tap pipe plug and check gas pressure by connecting a “U ” tube manometer (or similar pressure gauge) to the pressure tap . Refer to Figure 45. DRY961S PRESSURE Figure 45 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 60: Installing The No. 402P3 Kit

    PRESSURE TAP DRY967S the closed position. Refer to Figure 41. PIPE PLUG b. Disconnect igniter wires at quick disconnect Figure 47 blocks. Refer to Figure 47. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 61 Refer Figure 48 to Figure 50 . (3) Start dryer, pressure should be 3.5 ± .2 inches (8.89 ± .508 cm). Refer to Figure 50. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 62 “e”. (2) Installed the vent screw, see step “g”. (3) Gas valve pressure must be 3.5 ± .2 inches (8.89 ± .508 cm), see step “l”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 63: Section 8 - Service Procedures Unique To Electronic Control Model Dryers

    DAMP DOWN VOLUME WRINKLE RESET NO HEAT MEMORY WRINKLE FREE FREE DRY1077S Model Level Part No. AG9439, AE9433, 59608 NG8839, NE8833 AGE959, AEE953 62147 AGE939, AEE933 62243 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 64: Dryer Operation

    (available free option has been selected. Clothes on some may be removed from the dryer at any models) time during the wrinkle-free portion. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 65: Customizing Programmed Cycles

    Press LESS to subtract drying time from the cycle. One press of the pad will change the time in one-minute intervals. Pressing and holding the pad down will 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 66: Signal

    Pressing the pad a third time will result in setting the loudest tone. To turn the signal off, press the pad until the © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 67: Electrical Service (Electric Dryers)

    NOTE: Connect the dryer to the power TERMINAL BLOCK IN DRYER supply with the MAXIMUM RATED VOLTAGE listed on the nameplate. DRY1063S PIGTAIL CONNECTION DIRECT CONNECTION Figure 53 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 68 (6) Reinstall access cover and screw. WARNING To reduce the risk of electric shock, disconnect the electrical service to the dryer before proceeding. W135 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 69 Dryer is shown with the access cover removed for illustration purposes only. To reduce the risk of an electric shock, NEVER operate the dryer with the access cover removed. W136 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 70 (11) Reinstall the access plate and screw to the dryer. rear of the dryer cabinet. (4) Remove the terminal bracket ground screw holding the green ground wire to the © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 71 Dryer is shown with the access cover removed for illustration purposes only. To reduce the risk of an electric shock, NEVER operate the dryer with the access cover removed. W136 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 72: Electrical Requirements (Gas Dryers)

    NOTE: A qualified electrician should check the polarity of the wall receptacle. If a voltage reading is measured other Figure 58 than that illustrated, the qualified electician should correct the problem. Figure 57 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 73: Service Procedures For Troubleshooting Electronic Control

    IMPORTANT: The diagnostic cycle is not intended local electrical utility company check it and to diagnose any components built into the control correct any problems. (i.e. relays, transformer, capacitors, etc.). 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 74 HEATER (COM) ORANGE (NO) THERMISTOR (P6) NEUTRAL WHITE (P3) THERMISTOR (P5) TRANSFORMER DOOR SWITCH GRAY (P2) BROWN GROUND (P1) GREEN (P4) MOTOR RELAY K1 DRY1068S Figure 59 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...
  • Page 75 1. This test routine will only light in the LED’s pertaining to the hardware model selected. 2. When the last step in the table is finished, the routine sequence will repeat. 3. East output is on for two seconds. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 76: Symptom: Failure Symptom

    If the symptom or problem corresponds to one of the symptoms detailed on the following pages, proceed to that flow chart. (The diagnostic cycle check does not have to be made.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 77: Symptom: Flashing Display

    “P2” and “P3” when door is closed door switch to the control. and “0” Volts when door is open? Recheck from beginning. If problem persists, replace control. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 78: Symptom: Blown Fuse Or Tripped Circuit Breaker

    Does fuse or breaker blow 15 Recheck from Recheck from beginning. If seconds after motor starts? beginning. problem persists, replace control. Check heater circuit for shorted, broken, loose or incorrect wiring. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 79: Symptom: Control Will Not Wake Up (No Led's Light) After Select Pad Is Pressed

    *166 Ohms ± 30% between “P3” Replace control. and “COM” terminals. Recheck from beginning. If problem exists, after checking for loose, broken or incorrect wiring, replace control. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 80: Symptom: Control Wakes Up (When Select Pad Is Pressed) But Motor Does Not Start Properly

    Did you hear relay click and do you read approximately 120 Volts Replace control. between terminals “P1” (fan) and “P3” (neutral)? Check motor overload protector, motor and motor switch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 81: Symptom: Heater Does Not Turn On Or No Heat

    Replace control. seconds? Verify that orange wire is connected to terminal “N.O.” on heat relay K2. Check motor switch, limit thermostat, exhaust, heater assembly or gas valve. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 82: Symptom: Improper Heat Or Drying Times

    (thermistor). Plug in power cord and still exists, always replace the press the REGULAR and GO PADS. thermistor before replacing the control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 83: Symptom: "Op" Appears In Time Display

    30° F. Did “oP” appear in display after Normal operation. three minutes. Recheck from beginning. If problem persists, always replace thermistor before replacing the control. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 84: Symptom: "Sh" Appears In Time Display

    “SH” condition if replace control. the temperature near thermistor is above 175° F. Cool thermistor down and go to "Symptom: Improper Heat Or Drying Times", Paragraph 84. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 85: Control Replacement

    When removing wires from wrapped properly. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 86: Section 9 - Internal Wiring Of Dryer Motor Switch

    OVERLOAD PROTECTOR DRY869S General Electric Motor with External Switch MAIN WINDING START WINDING OVERLOAD PROTECTOR 4 BLU 7 BLK 5 YEL DRY869S Emerson Motor with External Switch 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 87: Section 10 - Wiring Diagrams

    W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 88: Age939

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AG9439, NG8839, AGE959 AND AGE939 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 89: Models Ae9433, Ne8833, Aee953 And Aee933

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AE9433, NE8833, AEE953 AND AEE933 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 90: Models Ng6819 And Ag5419

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG6819 AND AG5419 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 91: Models Ne6813 And Ae5413

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE6813 AND AE5413 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 92: Models Agm659 And Agm639

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AGM659 AND AGM639 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 93: Models Aem653 And Aem633

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AEM653 AND AEM633 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 94: Models Ng4819, Ag4419, Agm459 And Agm439

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NG4819, AG4419, AGM459 AND AGM439 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 95: Models Ne4813, Ae4413, Aem453 And Aem433

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NE4813, AE4413, AEM453 AND AEM433 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 96: Models Ag3419, Agm359 And Agm339

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AG3419, AGM359 AND AGM339 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62310...

  • Page 97: Models Ae3413, Aem353 And Aem333

    Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AE3413, AEM353 AND AEM333 62310 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

This manual is also suitable for:

Ag seriesAee seriesAge seriesAem seriesAgm seriesNe series ... Show all

Table of Contents