Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems UT025
Summary of Contents for Alliance Laundry Systems UT025
- Page 1 Drying Tumblers Refer to page 3 for Model Numbers Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 70381401R5 February 2008...
- Page 3 Installation must conform with local codes or in the absence of local codes with: In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.” In Canada, installation must comply with Standards CSA B149.1 or Natural Gas and Propane Code CSA C22.1, latest edition, Canadian Electric Code, Part I.
-
Page 4: Table Of Contents
Table of Introduction..................Model Identification ................Customer Service.................. Contents Wiring Diagram ..................Safety Information................Important Safety Instructions ............... Programming the Electronic OPL Control ........Introduction to Programming ............... Signal ....................10 Reversing ....................10 Status Lights ..................10 Automatic Dry and Condition Mode ............ 11 Time Dry and No Heat Modes.............. -
Page 5: Model Identification
Introduction Model Identification Information in this manual is applicable to these models: Steam/Thermal Oil Electric HA025L LU025L ST025L HT025S HT025E HA025N LU025N ST025N HU025S HU025E HT025L PA025L SU025L LT025S LT025E HT025N PA025N SU025N LU025S LU025E HU025L PT025L UA025L PT025S PT025E 25 Pound HU025N PT025N... - Page 6 Introduction (Continued) Steam/Thermal Oil Electric HA055L SA055L UA055L HT055E HA055N SA055N UA055N HU055E HT055L ST055L UT055L Not Applicable ST055E 55 Pound HT055N ST055N UT055N SU055E HU055L SU055L UU055L UT055E HU055N SU055N UU055N UU055E AT075L LU075N STF75N AT075S ST075S AT075E AT075N NT075L SU075L HT075S...
-
Page 7: Customer Service
The wiring diagram is located in the junction or the source from which the machine was purchased or contactor box. contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121. -
Page 8: Safety Information
Safety Information Precautionary statements (“DANGER,” “WARNING” NOTE: The word “NOTE” is used to communicate and “CAUTION”), followed by specific instructions, installation, operation, maintenance or servicing are found in this manual and on machine decals. These information that is important but not hazard precautions are intended for the personal safety of the related. -
Page 9: Important Safety Instructions
Safety Information Important Safety Instructions 14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified Save These Instructions service personnel. 15. If not installed, operated and maintained in WARNING accordance with the manufacturer’s instructions or if there is damage to or mishandling of this product’s components, use of this product could Hazardous Voltage. - Page 10 Safety Information 23. Remove laundry immediately after tumbler stops. 29. DO NOT bypass any safety devices. 24. Always read and follow manufacturer’s 30. Solvent vapors from dry-cleaning machines instructions on packages of laundry and cleaning create acids when drawn through the heater of the aids.
-
Page 11: Programming The Electronic Opl Control
Programming the Electronic OPL Control One preprogrammed All of these cycles They may be They may be No Heat cycle may be used as modified for one modified and preprogrammed cycle without saved in the from the factory . . . being saved in memory as Custom Four preprogrammed... -
Page 12: Signal
Programming the Electronic OPL Control Signal Lights when door is open. DOOR OPEN Refer to Figure 3. NOTE: Display window also flashes. The signal has three loudness levels that can be set anytime the control is activated. Pressing the SIGNAL Lights when laundry is drying. -
Page 13: Automatic Dry And Condition Mode
Programming the Electronic OPL Control Automatic Dry and Condition Mode “AC:**” will be displayed when tumbler is in Auto Cool Down. Typical Cool Down times for fabric When a temperature is selected, “A0:00” will appear selections are preset as shown in Table 2. The Cool in the display window. -
Page 14: Time Dry And No Heat Modes
Programming the Electronic OPL Control Time Dry and No Heat Modes “AC:**” will be displayed when tumbler is in Auto Cool Down. Typical Cool Down times for fabric After temperature selection, press the TIME pad. selections are preset as shown in Table 2. The Cool Refer to Figure 6. -
Page 15: Custom
Programming the Electronic OPL Control Custom During Custom cycles, the display is the same as non- Custom Automatic cycles. The CUSTOM status light Frequently used cycles can be saved in the control’s will be on. memory as Custom cycles. Only one cycle can be When creating or changing a Custom cycle, record it saved for each temperature selection. -
Page 16: Special Cycle Mode
Programming the Electronic OPL Control Special Cycle Mode “AC:**” will be displayed when tumbler is in Auto Cool Down. Typical Cool Down times for fabric This allows the user to select the number of times the selections are preset. The Cool Down time can only be tumbler will cycle from heat-on to heat-off. -
Page 17: Temperature Sensor
Programming the Electronic OPL Control Temperature Sensor Temperature Display (°F/°C) To test the temperature sensor, hold COOL DOWN To select between Fahrenheit and Celsius display, hold pad and press the TEMP pad in the idle mode. This in the TEMP DISPLAY pad while pressing the TEMP will show the temperature detected by the control.
Need help?
Do you have a question about the UT025 and is the answer not in the manual?
Questions and answers