Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems AT170FG
Summary of Contents for Alliance Laundry Systems AT170FG
- Page 1 Drying Tumblers 170 Pound Capacity Refer to Page 5 for Model Numbers T021C Part No. M413487R1 www.comlaundry.com April 2002...
-
Page 2: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 3 DC, JC and SC Micro Control OM Models 380-415 VAC, 50 Hertz, 3 Phase Steam ....73 AT, DT, JT and ST Micro Control OM Models 460-480 VAC, 60 Hertz, 3 Phase Steam ....74 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 4: Section 1 - Safety Information
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 5: Locating An Authorized Service Person
Locating An Authorized Service Person Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts. -
Page 6: Section 2 - Introduction
Model Identification Information in this manual is applicable to these tumbler models: Steam AT170FG AT170CSH DC170FG DC170CSH DT170FG DT170CSH JC170FG JC170CSH JT170FG JT170CSH SC170FG SC170CSH ST170FG ST170CSH © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 7: Customer Service
When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. SERIAL PLATE WIRING DIAGRAM JUNCTION BOX COVER TMB1499S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 8: Safety Warnings And Decals
• Loading door switch MUST be operational before putting tumbler into service. • Junction box cover MUST be reinstalled after inspection or servicing of tumbler is completed. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 9: Section 3 - Troubleshooting
Inoperative timer. • Test timer and replace if inoperative. Broken, loose or incorrect wiring. • Refer to wiring diagram located on back of tumbler or in literature packet. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 10: Motor Overload Protector Cycles Repeatedly
• Test timer and replace if inoperative. Incorrect wiring. • Refer to wiring diagram located on back of tumbler or in literature packet. Inoperative motor contactor. • Test contactor and replace if inoperative. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 11: Gas Burner Does Not Ignite - Gas Models
• Refer to wiring diagram located on back of tumbler or in literature packet. Improper fan rotation. • May be due to improper wiring resulting in low air flow. Refer to Installation Manual. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 12: Burner Ignites And Goes Out Repeatedly - Gas Models
• Refer to wiring diagram located on back of tumbler or in literature packet. Improper fan rotation. • May be due to improper wiring resulting in low air flow. Refer to Installation Manual. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 13: Burner Repeatedly Cycles Off On High Limit Thermostat - Gas Models
• Refer to Installation Manual (supplied with tumbler) for make-up air requirements. Improper fan rotation. • May be due to improper wiring resulting in low air flow. Refer to Installation Manual. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 14: Tumbler Overheating
Door strike improperly adjusted. • Refer to Adjustment Section in this manual for door strike adjustment. Tumbler improperly leveled. • Refer to Adjustment Section in this manual for leveling adjustment. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 15: Tumbler Runs But No Steam To Coils - Steam Models
Trap functioning improperly. • Check trap for size and capacity. If trap is dirty or sluggish clean thoroughly or replace. Check return line for high back pressure. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 16: Tumbler Will Not Start, Time On Drying Timer, Door Closed
VOLTS OUT OF SWITCH COIL PUSH-TO-START SWITCH. CHECK FOR CHECK FOR BROKEN WIRE BROKEN WIRE REPLACE OR POOR FROM CONTROL PUSH-TO-START CONNECTION AT RELAY TERMINAL 1 SWITCH HARNESS PLUG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 17: Motor Runs But No Heat
GAS SHUT-OFF VALVE TURNED ON VALVE 120 VOLTS REPLACE PRESENT ON IEI CONTROL BLACK WIRE FROM IEI CONTROL CHECK GAS VALVE REPLACE COIL FOR OPEN GAS VALVE CIRCUIT © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 18: Cylinder Turns, But No Heat
TERMINAL OF STOVE HIGH LIMIT LOOSE WIRE TO RELAY THERMOSTAT 120 VOLTS PRESENT AT INPUT REPLACE STOVE HIGH LIMIT TERMINAL OF STOVE HIGH LIMIT THERMOSTAT THERMOSTAT (continued on following page) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 19 TO FAN MOTOR CONTACT 120 VOLTS PRESENT ON INPUT TERMINAL OF FAN CONTACTOR AUX REPLACE FAN CONTACTOR CONTACT CHECK FOR BROKEN OR LOOSE JUMPER WIRE TO CONTACTOR CONTACTS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 20: Section 4 - Grounding
To reduce the risk of electrical shock, de- energize the electrical circuit being connected to the tumbler before making any electrical connections. Never attempt to connect a live circuit. W070 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 21: Section 5 - Service Procedures
PANEL prevent damage. PANEL i. Open loading door, support door and remove TMB1498S both hinge pins holding door to hinge brackets. Figure 1 Refer to Figure 3. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 22: Push-To-Start Switch
Compress locking tabs on sides of light and e. Disconnect wires from switch terminals and push light through timer graphic panel. remove switch. NOTE: Refer to wiring diagram when rewiring switch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 23: Relay
Refer to Figure 1. relay. FRONT LOADING PANEL DOOR ATTACHING ASSEMBLY SCREWS DOOR HANDLE HINGE DOOR HINGES ACTUATOR DOOR HINGES WASHER T248PZ3C HINGE DOOR HINGE BRACKETS TMB1496S Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 24: Cooling And Drying Timers
WIRE LEADS COOLING LIGHT IGNITION RESET SWITCH TIMER GRAPHIC PANEL DRYING TIMER START SWITCH MOUNTING SCREW WIRE TIMER LEADS MOUNTING SCREW LIGHT TIMER KNOBS TMB1337P Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 25: Reversing/Nonreversing Switch
Refer to Figure 1. bracket. c. Remove control box cover. Refer to Figure 2. NOTE: Refer to wiring diagram when rewiring thermostat. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 26 W002 INSTANT ELECTRONIC IGNITION CONTROL THERMOSTAT LIGHTS CONTACT BLOCK TEMPERATURE GRAPHIC PANEL THERMOSTAT PROBE ATTACHING SCREW THERMOSTAT KNOB TUBE REVERSING/NONREVERSING TMB1336P SWITCH EMERGENCY STOP BUTTON Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 27: Opl Micro Control
Remove control box cover. Refer to Figure 2. or Figure 7. d. Remove emergency stop button from contact block. Refer to Figure 5 or Figure 7. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 28 P L A S IG IA L T IM S T O IN G T IM IA L IT IO TMB1326P MICRO CONTROL OM MODELS Figure 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 29: Fuse Holder
Unscrew fuse holder nut from side of control e. Remove screws holding buzzer to housing. housing. Refer to Figure 2. f. Pull fuse holder out of control housing. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 30 Section 5 Service Procedures SENSING PROBE LINT SCREEN THERMISTOR LINT TMB1746S SCREEN Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 31: Gas Valve
Purge remaining air until odor of gas is detected, then STOVE SHUT-OFF HIGH LIMIT VALVE THERMOSTAT VALVE UNION BURNER TUBE SPUD HOLDER IGNITER T339PE3C Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 32: Igniter
Remove ignition control unit. GAS LEAKS! Make sure that spudholder and orifices are positioned such that gas will be injected directly down the center of the burner. W269R1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 33: Stove High Limit Thermostat
Refer to Figure 9. d. Remove two screws holding thermostat to rear g. Remove thermostat. of tumbler. CABINET HIGH LIMIT THERMOSTAT WIRE LOAD READY SCREW THERMOSTAT T209SE1B Figure 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 34: Steam Coils
STEAM COILS brackets. T244PE1A c. Remove door from hinge brackets. Figure 11 d. Remove screws holding brackets to front panel. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 35: Loading Door Switch
MUST be reinstalled after service is completed. W328 SWITCH CORNER ATTACHING DRIVE SCREWS GUARD DOOR SWITCH ACTUATOR T210SE1A Figure 13 T315PE1A Figure 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 36: Airflow Switch
NUTS BRACKET ATTACHING SCREWS MOUNTING BRACKET SWITCH JACKSHAFT COTTER ASSEMBLY T212SE1A Figure 15 VANE SWITCH ATTACHING SCREWS T320PE1A Figure 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 37: Drive Belt
Loosen the four jackshaft assembly attaching screws. Refer to Figure 16. d. Rotate the adjusting nuts counterclockwise (approximately three turns). Refer to Figure 15. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 38: Cylinder Motor Pulley
Refer to Figure 17. TAPERED MOTOR BUSHING PULLEY T371PE1A SCREWS Figure 17 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 39: Cylinder Assembly
SETSCREWS MOUNTING REAR ADJUSTING SCREW MOUNTING BRACKET BEARING MOUNTING SCREW MOUNTING BRACKET ATTACHING SCREW SETSCREWS FRONT BEARING FRONT ASSEMBLY ADJUSTING REAR SCREW BEARING ASSEMBLY T533P Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 40: Fan Belt
Remove fan motor pulley. f. Remove screws holding fan motor to motor base. g. Disconnect wires from motor. NOTE: Refer to wiring diagram when rewiring motor. h. Remove fan motor. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 41: Fan Assembly
Reuse the longer old bushing BLOWER screws or order the screws shown in the parts SHAFT manual. BLOWER COVER PULLEY T337PE1B MODELS BUILT BEFORE 4/9/98 Figure 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 42 Section 5 Service Procedures MOTOR MOTOR PULLEY MOTOR BASE BUSHING ADJUSTING NUTS BLOWER COVER BUSHING T152K BLOWER SHAFT PULLEY MODELS BUILT 4/9/98 AND AFTER Figure 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 43: Trunnion Shaft Assembly
TRUNNION SHAFT MEASURE AT FOUR POINTS TAPE MEASURE TRUNNION CYLINDER T089SE1A Figure 21 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 44: Cylinder Drive Motor
Remove drive belt. g. After installing motor, adjust cylinder belt and drive belt. ATTACHING MOTOR SCREW MOTOR PULLEY MOTOR MOUNTING BRACKET ATTACHING T237PE3E Figure 22 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 45: Reversing Timer
Remove reversing timer. d. Remove reversing contactor. REVERSING CONTACTOR REVERSING TRANSFORMER TIMER FAN MOTOR CONTACTOR TERMINAL BLOCK RAIL TERMINAL STRIP T341PE3C CONTACTOR BOX Figure 23 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 46: Fan Motor Contactor
Remove vent pipe. d. Remove attaching screws and thimble assembly from duct box wrap. e. Remove attaching screws, duct box wrap, and damper assembly from tumbler. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 47: Section 6 - Adjustments
Place a level on the rib. b. Check the side to side level by placing a level on access panel top and rear frame top angle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 48: Main Gas Burner Air Inlet Shutters
Adjust air shutter as follows: INSUFFICIENT AIR FLOW AIR SHUTTER ADJUSTING SCREW PROPER AIR FLOW AIR SHUTTER ADJUSTING SCREW NO AIR FLOW AIR SHUTTER ADJUSTING SCREW T220SE3B Figure 25 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 49: Airflow Switch
The cylinder and fan will continue to operate even though the airflow switch is indicating insufficient airflow. AIR FLOW SWITCH T283i Figure 26 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 50: Loading Door Switch
8-15 lbs. (17.6-33 kg) of pull is required to open door. To adjust, open door, loosen nut and turn door strike screw in or out as required. Retighten nut. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 51: Drive Belt Tension
1/2 inch (13 mm). f. Tighten all nuts and screws. SIDE BRACKET SIDE BRACKET ATTACHING SCREW MOTOR MOUNTING BRACKET ADJUSTING NUTS ADJUSTING TUBE T237PE3C Figure 28 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 52: Cylinder Belt Tension
MOTOR PULLEY JACKSHAFT ASSEMBLY BOLT ATTACHING SCREWS MOUNTING BRACKET ATTACHING SCREWS PULLEY T213SE1A Figure 30 JACKSHAFT ASSEMBLY T317PE1B Figure 29 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 53: Cylinder Clearance
Turn both screws evenly to adjust top and bottom clearance. Turn one or the other adjusting screw in or out to adjust side clearance. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... - Page 54 T218SE3A Figure 31 ADJUSTING SCREW LOCKNUT REAR ADJUSTING SCREW REAR BEARING MOUNTING SCREW TMB1500S FRONT FRONT ADJUSTING BEARING ASSEMBLY REAR SCREW COLLAR BEARING ASSEMBLY COLLAR Figure 32 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
-
Page 55: Section 7 - Wiring Schematics
W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 56: Manual Timer Models 208-230 Vac, 60 Hertz, 3 Phase Gas
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 208-230 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 57: 380-415 Vac, 50 Hertz, 3 Phase Gas
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 380-415 VAC, 50 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 58: 460 Vac, 60 Hertz, 3 Phase Gas
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 460 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 59: 208-240 Vac, 60 Hertz, 3 Phase Steam
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 208-240 VAC, 60 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 60: 380-415 Vac, 50 Hertz, 3 Phase Steam
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 380-415 VAC, 50 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 61: 460 Vac, 60 Hertz, 3 Phase Steam
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MANUAL TIMER MODELS 460 VAC, 60 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 62: Micro Control Mm Models 208-230 Vac, 60 Hertz, 3 Phase Gas
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MICRO CONTROL MM MODELS 208-230 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 63: 460 Vac, 60 Hertz, 3 Phase Gas
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MICRO CONTROL MM MODELS 460 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 64: 460 Vac, 60 Hertz, 3 Phase Steam
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MICRO CONTROL MM MODELS 460 VAC, 60 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 65: At, Dt, Jt And St Micro Control Om Models 208-230 Vac, 60 Hertz, 3 Phase Gas
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 208-230 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 66: 380-415 Vac, 50 Hertz, 3 Phase Gas
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 380-415 VAC, 50 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 67: Dc, Jc And Sc Micro Control Om Models 380-415 Vac, 50 Hertz, 3 Phase Gas
W030 DC, JC AND SC MICRO CONTROL OM MODELS 380-415 VAC, 50 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 68: At, Dt, Jt And St Micro Control Om Models 460-480 Vac, 60 Hertz, 3 Phase Gas
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 460-480 VAC, 60 HERTZ, 3 PHASE GAS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 69: 208-230 Vac, 60 Hertz, 3 Phase Steam
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 208-230 VAC, 60 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 70: 380-415 Vac, 50 Hertz, 3 Phase Steam
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 380-415 VAC, 50 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 71: Dc, Jc And Sc Micro Control Om Models 380-415 Vac, 50 Hertz, 3 Phase Steam
W030 DC, JC AND SC MICRO CONTROL OM MODELS 380-415 VAC, 50 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487... -
Page 72: At, Dt, Jt And St Micro Control Om Models 460-480 Vac, 60 Hertz, 3 Phase Steam
W030 AT, DT, JT AND ST MICRO CONTROL OM MODELS 460-480 VAC, 60 HERTZ, 3 PHASE STEAM © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M413487...
Need help?
Do you have a question about the AT170FG and is the answer not in the manual?
Questions and answers