Alliance Laundry Systems 75 Service Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Dryer
  5. 75
  6. Service manual
Alliance Laundry Systems 75 Service Manual

Alliance Laundry Systems 75 Service Manual

75 pound/635 liter capacity drying tumblers
Hide thumbs Also See for 75:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual , Operation and Maintenance
Drying Tumblers
75 Pound Capacity
634 Liter Capacity
Refer to Page 5 for Model Numbers
T012c
T012C
Part No. M411433R1
www.comlaundry.com
October 2001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 75 and is the answer not in the manual?

Questions and answers

Related Manuals for Alliance Laundry Systems 75

Summary of Contents for Alliance Laundry Systems 75

  • Page 1 Drying Tumblers 75 Pound Capacity 634 Liter Capacity Refer to Page 5 for Model Numbers T012c T012C Part No. M411433R1 www.comlaundry.com October 2001...

  • Page 2: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 3 79. Main Gas Burner Air Inlet Shutters ....68 80. Airflow Switch..........69 81. Loading Door Switch ........71 82. Loading Door Strike ........72 83. Drive Belt Tension ..........72 84. Drive Tension..........75 85. Cylinder Clearance..........76 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 4: Section 1 - Safety Information

    • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R1 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 5: Locating An Authorized Service Person

    Locating An Authorized Service Person Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.

  • Page 6: Section 2 - Introduction

    DTB75EG JCB75CSH SCB75CE DTB75FG JCB75CSL ST75CE JCB75CG JT75CSH STB75CE JT75CG JT75CSL JT75EG JTB75CSH JTB75CG JTB75CSL JTB75EG SCB75CSH SCB75CG SCB75CSL ST75CG ST75CSH STB75CG ST75CSL STB75EG STB75CSH STB634 STB75CSL M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 7: Customer Service

    When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. T419IE3B © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 8: Safety Warnings And Decals

    • Loading door switch MUST be operational before putting tumbler into service. • Junction box cover MUST be reinstalled after inspection or servicing of tumbler is completed. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 9: How A Tumbler Works

    The air then passes through the lint filter, exhaust fan, and is vented to the outdoors. NOTE: In Energy Saver Models, some of the exhaust air is recirculated. Refer to illustration on page 9. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 10 Section 2 Introduction Fresh Air Combustion Air Mixed Air Recirculating Air T007CE1A Exhaust Air Energy Saver Models M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 11: Section 3 - Troubleshooting

    • Test run switch and replace if inoperative. (accumulator). Broken, loose, or incorrect wiring. • Refer to wiring diagram located on back of tumbler or in literature packet. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 12: Motor Overload Protector Cycles Repeatedly

    Metered Models: Inoperative accumulator. • Test accumulator and replace if inoperative. Incorrect wiring. • Refer to wiring diagram located on the back of tumbler or in literature packet. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 13: Heating Element Does Not Heat Or Burner Does Not Ignite

    • Test sensor and replace if inoperative. Inoperative sensor. Gas and Electric Models: • Test thermostat and replace if inoperative. Inoperative high limit thermostat. (continued on next page) M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 14 • Open lint door panel, place lint door panel back on tumbler (ensuring a tight fit) then latch. Broken, loose, or incorrect wiring. • Refer to wiring diagram located on back of tumbler or in literature packet. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 15: Igniter Glows, Flame Sensor Opens But No Ignition - Gas Models

    • Tumbler is equipped for type of gas specified on serial plate. If orifices are different from that specified on serial plate, obtain and install proper orifices. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 16: Heating Element Or Burner Shuts-Off Prematurely

    • Replace thermostat. temperature. Lint door panel not closed properly. • Remove lint door panel, place lint door panel back on tumbler (ensuring a tight fit) then latch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 17: Heating Element Or Burner Does Not Shut-Off

    Restricted or inadequate exhaust system. • Remove obstruction or lint build-up from exhaust ductwork. Refer to the Installation Manual (supplied with tumbler) for exhaust system requirements. Inoperative thermostat. • Replace thermostat. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 18: Burners Not Burning Properly - Gas Models

    • Check for inlet and outlet markings on check valve, and invert is necessary. Clogged strainer. • Remove strainer and clean. Inoperative timer or thermostat. • Test timer or thermostat, replace if inoperative. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 19: Water In Steam Line - Steam Models

    If the temperature of the tumbler is above 24°F and signal sounds (-4.4°C). (-4.4°C), replace temperature sensor. three minutes after Temperature sensor open. Replace temperature sensor. tumbler is started M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 20: Tumbler Will Not Start, Time On Drying Timer, Door Closed (Manual Timer Models)

    SWITCH REPLACE MOTOR REPLACE REPLACE CHECK FOR PUSH-TO-START CHECK FOR RELAY BROKEN WIRE SWITCH BROKEN WIRE FROM CONTROL OR POOR RELAY TERMINAL 1 CONNECTION AT HARNESS PLUG © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 21: Motor Runs, Time On Drying Timer But No Heat

    HIGH LIMIT HIGH LIMIT HIGH LIMIT AT HARNESS PLUG THERMOSTAT THERMOSTAT THERMOSTAT CHECK FOR REPLACE REPLACE BROKEN WIRE BURNER THERMOSTAT FROM CABINET HIGH LIMIT HIGH LIMIT THERMOSTAT M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 22: Igniter Does Not Glow

    MAIN COIL? OPEN? OPEN? REPLACE ADJUST REPLACE DIODE REPLACE DIODE REPLACE COMPLETE IGNITER GAP TO LOGIC BOARD LOGIC BOARD MAIN COIL GAS VALVE 1/8 IN. TO 1/4 IN. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 23: Igniter Does Not Spark

    TERMINAL? GAS SHUT-OFF OPEN GAS VALVE SHUT-OFF OPEN? VALVE 120 VOLTS REPLACE PRESENT ON BLACK WIRE CONTROL FROM IEI CONTROL CHECK GAS VALVE COILS REPLACE AS REQUIRED M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 24: Section 4 - Grounding

    To reduce the risk of electrical shock, de- energize the electrical circuit being connected to the tumbler before making any electrical connections. Never attempt to connect a live circuit. W070 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 25: Section 5 - Service Procedures

    Refer to Figure 2 for Coin Drop Models or Figure 3 for Manual Timer Models. NOTE: Refer to wiring diagram when rewiring light. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 26 ACCESS PANEL CONTROL PANEL ATTACHING SCREWS SCREWS PUSH-TO-START SWITCH T056SE3D WIRE HARNESS TERMINAL PLUG BOARD T057SE3A CONTROL PUSH-TO-START CONTROL PANEL PANEL BRACKET SWITCH ASSEMBLY BRACKETS Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 27: Relay (Manual Timers Models)

    IMPORTANT: Be sure barrier is installed in proper position when reinstalling drying timer. Refer to Figure 2 Figure 3. NOTE: Refer to wiring diagram when rewiring timer. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 28: Cooling Or Drying Timer Motor

    (2) Connect timer terminal wire 3 to terminal the timer motor fails. board terminal B. a. Remove control panel. (3) Connect timer terminal 5 wire to terminal b. Disconnect motor leads. board terminal C. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 29: Coin Meter

    Remove four speed nuts holding coin meter to coin meter frame. NOTE: Refer to wiring diagram when rewiring coin meter. Connect wires cut in step “c” above with new wire nut. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 30: Coin Meter Timer Motor

    Disconnect wires from switches on timer. c. Hold switches and actuating bracket under switches tightly together with one hand while removing two screws holding switches to timing motor mounting bracket. Carefully © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 31: Electronic Control (Mm Models)

    Always handle electronic control by its metal edges. If a wrist strap is not available, touch tumbler while it is plugged in before handling control to dissipate any charge. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 32 CONTROL PLUG BATTERY REVERSING/ PLASTIC NON REVERSING CLAMP SWITCH BATTERY PLUG T094SE3C Figure 8 ELECTRONIC CONTROL BRACKET SWITCH (Reversing) SWITCH PLATE CONTROL T332PE3C (Reversing) PLUG Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 33: Control Thermostat

    Refer to Figure 12. THERMOSTAT IMPORTANT: When reinstalling thermostat, be SENSING TUBE sure to secure sensing probe with locking tabs on Figure 11 bracket. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 34 • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded. W002 THERMOSTAT THERMOSTAT SENSING PROBE SENSING TUBE SENSING PROBE WARNING LOCKING TABS LINT T014SE3A SCREEN Figure 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 35: Thermistor

    Disconnect the wires from the back of the thermistor. THERMISTOR OM Models THERMISTOR WIRES T345P SCREW PERFORATED COVER LINT T093SE3C PANEL Figure 13 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 36: Gas Valve

    Disconnect wires from diode logic board assembly. terminals. Refer to Figure 14. d. Disconnect igniter wires from diode logic NOTE: Refer to wiring diagram when rewiring board. diode logic board. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 37 T002SE3D COIL REDUNDANT COIL White Rodgers WHITE RODGERS WHITE RODGERS White Rodgers Glow-Bar Instant Electronic System (IEI) GLOW-BAR GAS VALVE INSTANT ELECTRONIC IGNITION GAS VALVE Figure 15 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 38: Sensor

    Attempted repair or tampering with the ignition control unit will void its warranty. d. Remove two screws attaching ignition control unit to cabinet frame. e. Remove ignition control unit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 39: Main Coil

    NOTE: Contactors and terminal blocks are located in contactor box at the rear of the tumbler. a. Remove screw holding cover to contactor box and remove cover. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 40: Heater Element

    Tilt element up and gently slide it out of housing. IMPORTANT: Bottom guard must be put back on bottom of housing before reinstalling heater on tumbler. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 41 GUARD HIGH LIMIT THERMOSTAT SCREW BUS BAR HEATER ELEMENT T231PE3D Newer Models: JUMPER HEATER WIRES HOUSING SCREW BUS BAR HIGH LIMIT THERMOSTAT HEATER ELEMENT T422PE3A Figure 17 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 42: Stove High Limit Thermostat

    HIGH LIMIT h. Disconnect wires from thermostat. THERMOSTAT i. Remove two screws holding thermostat to mounting bracket. Refer to Figure 19. MOUNTING BRACKET SCREWS TU026-SV Figure 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 43: Cabinet High Limit Thermostat

    Remove two screws attaching thermostat to mounting bracket. NOTE: Refer to wiring diagram when reconnecting thermostat wires. CABINET HIGH LIMIT THERMOSTAT COVER MOUNTING BRACKET TU076-SV Figure 20 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 44: High Limit Thermostat

    Remove steam coils by lifting straight up and out of tumbler. IMPORTANT: When removing or replacing steam coils, be careful not to damage fins on steam coils. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 45: Loading Door Assembly

    NOTE: Nylon washer must be in place on lower pin when reinstalling loading door. LOADING DOOR ASSEMBLY LOADING DOOR HINGE HINGE BOLT HINGE ATTACHING SCREWS HINGE BRACKET T028SE1A Figure 21 T029SE1A Figure 22 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 46: Loading Door Handle

    Remove screws holding door handle to door frame. HANDLE STYLE BAR STYLE ATTACHING SCREW DOOR ATTACHING SCREWS LOADING LOADING DOOR HANDLE SCREW DOOR DOOR TU030-SV TU031-SV Figure 23 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 47: Front Panel

    Refer to Figure 24. NOTE: When removing front panel, lower panel slightly to make sure door switch rod clears hole in cabinet. T032SE1D SPEED NUTS Figure 24 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 48: Loading Door Switch

    Apply upward pressure on the welded clip to allow switch rod snap free. Refer to Figure 26. SCREWS T034SE1C Figure 25 DOOR SWITCH SPRING CLIP T036SE1B Figure 26 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 49: Airflow Switch Assembly

    (if equipped) are not pinched between rear of cabinet and wire T037SE1B cover or between cover plate and channel. Figure 27 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 50: Drive Guard

    Loosen four capscrews holding motor mounting bracket to side brackets. Lower motor and mounting bracket until holding capscrews bottom in the mounting slots. e. Slip drive belt off motor pulley. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 51: Drive Chain

    Pull complete idler housing assembly with belt guard. guide rails away from the back of the tumbler. g. After repairing or replacing idler housing assembly, reinstall chain, belt and drive guard. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 52 GUIDE RAIL BOLT AND NUT CHAIN TAKE-UP SPROCKET DRIVE SPROCKET IDLER HOUSING ATTACHING BOLT AND IDLER RAILS BELT LOWER GUIDE RAIL BOLT SHEAVE AND NUT TU202-PT Figure 30 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 53 MOTOR CYLINDER PULLEY MODELS MOTOR MOTOR BRACKET MOUNTING BOLTS BELT MOTOR MOUNTING BOLTS TRUNNION HOUSING ASSEMBLY BUSHING DRIVE CHAIN CYLINDER SPROCKET SHEAVE DRIVE SPROCKET T201PE3B Figure 31 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 54: Idler Sprocket

    NOTE: After installing sheave, adjust belt, then drive motor mounting screws and repositioning adjust chain. Refer to Adjustments Section. motor on mounting bracket. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 55: Cylinder Sprocket/Upper Sheave

    Refer to Adjustments Section. Adjustments Section. NOTE: After installing cylinder and shaft, adjust cylinder clearance. Refer to Adjustments Section. k. Reinstall drive guard on tumbler. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 56: Trunnion Housing Assembly

    NOTE: If a press is not available to install bearings, SCREW SMALL TRUNNION carefully tap bearings into housing. BEARING HOUSING TU192-PT g. Reinstall drive guard on tumbler. Refer to Figure 28. Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 57: Trunnion Shaft Assembly

    Reinstall drive guard on tumbler, Figure 28. Measure the distance between the center of the TRUNNION MEASURE AT ASSEMBLY FOUR POINTS TAPE MEASURE CYLINDER T089SE3C Figure 34 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 58: Motor And Fan Assembly

    Remove screws holding belt guard to motor bracket and remove belt guard. Refer to Figure 29. f. Loosen nut and washer from lower guide rail bolt. Refer to Figure 30 or Figure 31. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 59 Take care to avoid losing or damaging the washer. MOTOR FAN HOUSING COVER SPACER WASHER PULLEY JAM NUT MOTOR PULLEY LOCKNUT T046SE3A Figure 36 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 60: Cylinder Drive Motor

    On later models, lower adjusting bolt to lessen and adjust motor position on mounting bracket. belt tension. MOTOR After 1996: PULLEY CYLINDER MOTOR MOTOR BRACKET ADJUSTING BOLT T472P_ Figure 37 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 61 Section 5 Service Procedures Prior to 1996: MOTOR CYLINDER PULLEY MOTOR SIDE BRACKET BELT GUARD MOTOR MOUNTING BRACKET SIDE BRACKET TU142-PT Figure 38 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 62: Reversing Control Electrical Components

    Electronic reverser has no motor or to back wall of reversing control box. Refer switches. to Figure 39. NOTE: OM microprocessor doesn’t have a mechanical or electronic reversing timer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 63 Section 5 Service Procedures CONTROL SCREW COVER TIMER MOTOR SWITCH REVERSING TIMER ASSEMBLY TRANSFORMER (480 Volt only) GROUND SCREW GROUND COIL (240 Volt) SCREW CONTACTOR REVERSING CONTACTORS TU140-PT Figure 39 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 64: Section 6 - Adjustments

    All four legs must rest firmly on the floor so weight of tumbler is evenly distributed. Tumbler must not rock. Figure 40 d. Replace lint panel. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 65: Main Gas Burner Air Inlet Shutters

    A flame pattern that flares to the AIR SHUTTER right and left, indicates that no air is flowing ADJUSTING SCREWS TU019-KT through the tumbler. Figure 41 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 66: Airflow Switch

    The counterweight should be adjusted so the disc moves away from the cabinet when the lint panel is opened 1-1/2 inches (38.1 mm). Adjust the airflow switch as follows: M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 67 SWITCH AIRFLOW SWITCH MOUNTING BRACKET REAR PANEL OF TUMBLER SWITCH SWITCH LEVER LEVER SPRING CLIP VANE LEVER COUNTER WEIGHT DISC SPRING CLIP COUNTERWEIGHT DISC TU050-SV Figure 42 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 68: Loading Door Switch

    If switch position doesn’t achieve proper operation, bend tab outward and repeat steps SWITCH “a” and “b”. BRACKET INTERLOCK T249IE1C Figure 43 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 69: Loading Door Strike

    Tighten adjusting screw locknuts and side bracket mounting screws securely, taking care Figure 44 to keep mounting bracket level so as not to disturb alignment of motor pulley. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 70 MOTOR PULLEY GROUND WIRE (Green) T229IE3C NOTE: Tumbler is shown with guards removed for ilustration purposes only. Never operate the tumbler with the guards removed. Figure 45 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 71 BOLT V-BELT 1/2" (13 mm) DEFLECTION CYLINDER SPROCKET CYLINDER DRIVE CHAIN 1/2" (13 mm) DEFLECTION SHEAVE GUIDE RAILS IDLER HOUSING ATTACHING BOLT AND NUT T324PE3B Figure 46 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...

  • Page 72: Drive Tension

    “high point” when making the d. Check chain or belt tension after tightening jam adjustment. nut on idler housing attaching bolt. M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 73: Cylinder Clearance

    7/16" (11.113 mm) CYLINDER RIM / FRONT PANEL FLANGE FRONT 9/32" ± 1/32" CLEARANCE PANEL FRONT PANEL FLANGE (Top Shown) FORE / AFT CLEARANCE T218SE3B Figure 47 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT M411433...
  • Page 74 Section 6 Adjustments BELT/CHAIN LOCKNUTS TRUNNION HOUSING NONREVERSING ADJUSTING BOLTS MODELS TRUNNION HOUSING BOLTS (2 per side) TU202-PT Figure 48 M411433 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

This manual is also suitable for:

634Atb75cgDcb75cgDcb75fgDtb634Dtb75cg ... Show all

Table of Contents