Sullair 600H User Manual page 9

SECTION 1
H. Open fluid filler cap only when compressor is not
running and is not pressurized. Shut down the
compressor and bleed the sump (receiver) to
zero internal pressure before removing the cap.
I. Vent all internal pressure prior to opening any
line, fitting, hose, valve, drain plug, connection or
other component, such as filters and line oilers,
and before attempting to refill optional air line
anti-icer systems with antifreeze compound.
J. Keep personnel out of line with and away from
the discharge opening of hoses, tools or other
points of compressed air discharge.
K. DO NOT use air at pressures higher than 30 psig
(2.1 bar) for cleaning purposes, and then only
with effective chip guarding and personal protec-
tive equipment per OSHA Standard 29 CFR
1910.242 (b) or any applicable Federal, State
and Local codes, standards and regulations.
L. DO NOT engage in horseplay with air hoses as
death or serious injury may result.
M. This equipment is supplied with an ASME
designed pressure vessel protected by an ASME
rated relief valve. Lift the handle once a week to
make sure the valve is functional. DO NOT lift
the handle while machine is under pressure.
N. If the machine is installed in an enclosed area it
is necessary to vent the relief valve to the outside
of the structure or to an area of non-exposure.
O. DO NOT remove radiator filler cap until the cool-
ant temperature is below its boiling point. Then
loosen cap slowly to its stop to relieve any
excess pressure and make sure coolant is not
boiling before removing cap completely. Remove
radiator filler cap only when cool enough to touch
with a bare hand.
P. The ethyl ether in the replaceable cylinders used
in diesel ether starting aid systems (optional) is
under pressure. DO NOT puncture or incinerate
those cylinders. DO NOT attempt to remove the
center valve core or side pressure relief valve
from these cylinders regardless of whether they
are full or empty.
Q. If a manual blowdown valve is provided on the
receiver, open the valve to ensure all internal
pressure has been vented prior to servicing any
pressurized component of the compressor air/
fluid system.
1.4 FIRE AND EXPLOSION
WARNING
Do not attempt to operate the compressor
in any classification of hazardous environ-
ment or potentially explosive atmosphere
unless the compressor has been specially
designed and manufactured for that duty.
A. Refuel at a service station or from a fuel tank
designed for its intended purpose. If this is not
possible, ground the compressor to the dis-
penser prior to refueling.
B. Clean up spills of lubricant or other combustible
substances immediately, if such spills occur.
C. Shut off air compressor and allow it to cool. Then
keep sparks, flames and other sources of ignition
away and DO NOT permit smoking in the vicinity
when adding fuel, checking or adding electrolyte
to batteries, checking or adding fluid, checking
diesel engine ether starting aid systems, replac-
ing cylinders, or when refilling air line anti-icer
systems antifreeze compound.
D. DO NOT permit fluids, including air line anti-icer
system antifreeze compound or fluid film, to
accumulate on, under or around acoustical mate-
rial, or on any external surfaces of the air com-
pressor. Wipe down using an aqueous industrial
cleaner or steam clean as required. If necessary,
remove acoustical material, clean all surfaces
and then replace acoustical material. Any acous-
tical material with a protective covering that has
been torn or punctured should be replaced
immediately to prevent accumulation of liquids or
fluid film within the material. DO NOT use flam-
mable solvents for cleaning purposes.
E. Disconnect and lock out all power at source prior
to attempting any repairs or cleaning of the com-
pressor or of the inside of the enclosure, if any.
F. Keep electrical wiring, including all terminals and
pressure connectors in good condition. Replace
any wiring that has cracked, cut, abraded or oth-
erwise degraded insulation, or terminals that are
worn, discolored or corroded. Keep all terminals
and pressure connectors clean and tight.
G. Turn off battery charger before making or break-
ing connections to the battery.
9