Preparing To Install; Installation - BESAFE iZi Flex S FIX User Manual

10

Preparing to install

• Adjustable headrest
• Shoulderbelt lock
• Shoulderbelt guider
• Backrest
• Base
• ISOfix release handle
• SIP bumper
• Height adjustment handles (2x)
• ISOfix connectors (2x)
• ISOfix release buttons (2x)
• ISOfix indicators (2x)
• ISOfix vehicle anchorage (2x)

Installation

1. When installing the seat in the front vehicle seat make sure the
backrest of the vehicle seat is in an upright position.
2. Position the seat inside the vehicle.
3. Pull the ISOfix release handle to release the ISOfix connectors. A
button on top of the handle will keep the handle in the released
position and locks the ISOfix connectors from sliding back into the
base again. The ISOfix arms lock only in the position where they are
extended completely. In this locked position 2 red marks next to the
button on the handle will become visible. (2, 3)
4. Click the ISOfix connectors onto the ISOfix anchorage points in the
vehicle seat. Make sure that all ISOfix indicators are GREEN. (4, 5, 6)
5. Press the button down on top of the ISOfix release handle (located
between the red marks) and push the handle back into the base.
Push the seat back as far as possible towards the backrest of the
vehicle seat. (7, 8, 9)
6. Make sure the back of the seat is touching the backrest of the vehicle
seat. If the headrest of the vehicle is pushing the seat away from the
backrest, adjust the headrest. (9)
7. If the seat cannot be used in combination with ISOfix anchorage
points in the vehicle seat, the ISOfix connectors can be stowed inside
the seat and the seat can be used in combination with the 3-point
belt only.
8. Slide the shoulderbelt into the shoulderbelt guide. Make sure the belt
is not twisted and that the shoulderbelt guide is closed again to keep
the belt inside. (10, 11)
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
Positioning of the child
1. Adjust the headrest to the correct height by turning the height adjuster
handle. Make sure that the shoulder belt is level with your child's
shoulder. (12, 13)
2. Position the vehicle belt in front of the child and lock the belt into the
buckle of the vehicle. (14, 15)
3. Remove slack in the belt by pulling the belt towards the retractor. (16)
Removing the seat
1. Remove the shoulderbelt out of the shoulderbelt guide by pushing the
shoulderbelt lock in the guider up and slide the belt out. (17, 18)
2. Pull the ISOfix release handle to release the ISOfix connectors. In this
way the base of the seat can move forwards and the ISOfix release
buttons can be operated. (19, 20)
3. Release both ISOfix connectors, by pushing down the release buttons.
(21) Slide the arms with ISOfix connectors inside the seat before you
remove the seat from the vehicle. To be able to slide the arms with
ISOfix connectors inside the seat, press the button down (between the
red marks) on top of the ISOfix release handle. (22, 23)
4. Remove the seat from the vehicle.
Installation of 3 car seats
1. The SIP bumper on the inner side of the vehicle can be removed from
the seat to create more space next to the seat for an additional car
seat in the middle position of the vehicle. Remove a side bumper only
on the inner side of the vehicle and never on the door side. (24, 25)
2. To remove a SIP bumper, push the button and move the bumper
sideways and to the back, to hook it out of the fabric hooks. Keep the
SIP bumper for later usage. (26, 27)
3. To install a SIP bumper, first hook in the lower hook, then hook in the
upper hook and finally secure the bumper in the middle by pushing
the button first and releasing it when it is positioned against the seat.
Check if the SIP bumper is connected correctly. Use the SIP bumper
only on the door side of the vehicle. (28, 29, 30)
11