Download
Share
Print this page
  1. Manuals
  2. Brands
  3. DaVinci Manuals
  4. Indoor Fireplace
  5. 72 SS Timber
  6. Installation instructions manual

DaVinci 72 SS Timber Installation Instructions Manual

Fire log set
Hide thumbs

Advertisement

Quick Links

Download this manual
 
 
 
Compatibility
72" DaVinci Timber Fire (Single Sided)
Overview
This kit includes all the logs and media needed for installation into the 72"- single sided DaVinci Timber Fire
Fireplace. The log set has duplicates of some logs, but their positioning disguises the fact that they are the same.
Pay close attention to the log placement to ensure that the logs do not obstruct any of the burner holes.
Installation Warnings
NOTE: The fireplace should be in place and vented and the firebacks must be installed prior to installing the log set.
The logs are fragile, especially after being exposed to heat.
Make sure the gas control valve is OFF and the heater is cool prior to conducting service.
Failure to position the parts in accordance with these diagrams or failure to use only parts specifically
approved with this appliance may result in property damage or personal injury.
The burner must be correctly positioned before installing the log set. Make sure the burner is fully seated and
the pilot is properly aligned. See owner's manual for details on burner removal.
72" Timber Fire Log Installation Overview
This log set is used in the single sided 72" version of the Timber Fire. There are multiple of some logs in the set.
Some face the service side of the fireplace and the other of the same log will face the back wall of the firebox so
only the back portion of the log is visible.
NOTE: Make sure that the firebacks are installed before installing the log set.
Log #9 
Log #8 
Log #4 
Page 1 of 24
DaVinci 72" SS Timber Fire Log Set
Installation Instructions
Log #5 
Log #2 
17602248 — 7/25/22
WARNING
Log #7 
Log #6 
Log #3 
Log #8 
Log #10 
Log #1 
© Travis Industries, Inc.

Advertisement

loading

Related Manuals for DaVinci 72 SS Timber

Summary of Contents for DaVinci 72 SS Timber

  • Page 1 Overview This kit includes all the logs and media needed for installation into the 72”- single sided DaVinci Timber Fire Fireplace. The log set has duplicates of some logs, but their positioning disguises the fact that they are the same.

  • Page 2: Packing List

    DaVinci 72” SS Timber Fire Log Set Installation Instructions       Packing List Log #1 Log #2 Log #3 Log #4 Log #5 Log #6 Log #7 Log #8 Log #9 Log #10 Burner Cluster Log Locating Covers Pins...

  • Page 3: Order Of Installation

    DaVinci 72” SS Timber Fire Log Set Installation Instructions       Tools Required  Glass lifting suction cup set (sku# - 94400914) Installation Notes WARNINGS:  Make sure the gas control valve is OFF and the heater is cool prior to conducting service.

  • Page 4: Firebox Preparation

    DaVinci 72” SS Timber Fire Log Set Installation Instructions       Firebox Preparation 1. Remove the (6) screws that secure the burner to the fireplace. Set the screws aside for reinstallation. 2. Remove the burner by lifting the assembly straight up and remove it from the fireplace.
  • Page 5 DaVinci 72” SS Timber Fire Log Set Installation Instructions       4. Remove each of the log grates from the fireplace. 5. If not already done, Install the firebacks at this time (see instructions in the appliance manual).  ...
  • Page 6 DaVinci 72” SS Timber Fire Log Set Installation Instructions       Reinstall the burner into the fireplace. The firebox should now look as shown below. Faces the rear glass Faces you 9. Install one of the log #1's in the back left corner of the log grate.
  • Page 7 DaVinci 72” SS Timber Fire Log Set Installation Instructions       Faces you Faces the rear glass 11. Install one of the #2 logs on the back right of the log grate as shown to the right. Looking at...
  • Page 8 DaVinci 72” SS Timber Fire Log Set Installation Instructions       Faces the rear glass Faces you 13. Install one of the #3 logs as shown to the right. The front of the log faces the rear glass and fits between the two rear logs already installed.
  • Page 9 DaVinci 72” SS Timber Fire Log Set Installation Instructions       Faces the rear glass Faces you 15. Install one of the log #4's as shown to the right. The front of the log faces the wall of the firebox. Install the log on the right rear corner of the log grate.
  • Page 10 DaVinci 72” SS Timber Fire Log Set Installation Instructions       17. Use the (4) burner cluster cover pieces to obscure the view of the (4) burner clusters. The mouse hole in the burner cluster cover should line Mouse hole ...
  • Page 11 DaVinci 72” SS Timber Fire Log Set Installation Instructions       19. Install the small log filler piece as shown below. The filler piece fits tightly up against the cut branch on the left rear log #1. There is a hole on the bottom of the filler piece  ...
  • Page 12 DaVinci 72” SS Timber Fire Log Set Installation Instructions       HINT: Telling the difference between log #5 & log #6. Look at the top of both logs. The top of log #5 has a hole for a log locating pin and the top of log #6 does not.
  • Page 13 DaVinci 72” SS Timber Fire Log Set Installation Instructions       23. Install log #6 as shown to the right. There is a hole on the bottom of log #6 that rests over log locating pin #8. The charred end of the...
  • Page 14 DaVinci 72” SS Timber Fire Log Set Installation Instructions       26. Install the #5 log as shown below. Log #5 has two holes on the bottom that rest over log locating pins #6 (see step #18) and pin #16 (see step #25). The round hole rests on pin #6 and the elongated hole rests on pin #16 as shown below.
  • Page 15 DaVinci 72” SS Timber Fire Log Set Installation Instructions       27. Install one of the #8 logs (1 of 3) as shown. The hole on the right end of the log rests over pin #10 (see step 18).
  • Page 16 DaVinci 72” SS Timber Fire Log Set Installation Instructions       28. Install the second log #8 (2 of 3) as shown. The hole on the right end of the log rests over pin #2 (see step 18). The hole in the left end of the log rests over pin #1 (see step #18). The arc of the log points towards the center- front of the burner.
  • Page 17 DaVinci 72” SS Timber Fire Log Set Installation Instructions       29. Install the last #8 log (3 of 3) as shown. The hole on the right end of the log rests over pin #14 (see step 18). The hole in the left end of the log rests over pin #14 (see step #18).
  • Page 18 DaVinci 72” SS Timber Fire Log Set Installation Instructions       30. Install log #9 logs as shown. Log #9 has 2 elongated holes on the bottom of the log that rest over log placement pins #3 & #4. The cut branch on the top of the log points towards the front center of the fireplace.
  • Page 19 DaVinci 72” SS Timber Fire Log Set Installation Instructions       31. Install Log #10 as shown. Log #10 has two elongated holes on the bottom of the log that rest over log placement pins #12 & #13 (see step #18). The cut branch on the top of the log points towards the center rear of the fireplace.
  • Page 20 DaVinci 72” SS Timber Fire Log Set Installation Instructions       32. Place ember chunks on top of the Ember-Glo glass in front and to the sides of the log grate.   NOTE: Make sure that no glass or ember chunks are obstructing the slot where the inner glass will rest. If anything has fallen into the slot, remove it with a vacuum, small screwdriver, or compressed air.
  • Page 21 DaVinci 72” SS Timber Fire Log Set Installation Instructions       35. Place more ember chunks on the ember glass installed in the last step. NOTE: Make sure that no glass or ember chunks are obstructing the slot where the inner glass will rest.
  • Page 22 DaVinci 72” SS Timber Fire Log Set Installation Instructions       37. Reinstall the barrier screen onto the front of the fireplace. Insert the top of the screen behind the front surface of the fireplace and push it upward until the bottom of the screen clears the bottom of the fireplace opening. With the screen pressed into the opening, let the lower edge of the screen to drop below the front edge of the fireplace opening.

  • Page 23: Replacement Part Numbers

    DaVinci 72” SS Timber Fire Log Set Installation Instructions       Replacement Part Numbers Replacement Part #s Front View Top View Log #1 250-XXXXX Log #2 250-XXXXX Log #3 250-XXXXX Log #4 250-XXXXX Log #5 250-XXXXX   Log #6...
  • Page 24 DaVinci 72” SS Timber Fire Log Set Installation Instructions Other Replacement Part Other Replacement Part Numbers Numbers Large Log Small Log Filler Piece Filler Piece 250-XXXXX 250-XXXXX placement Ember-Glo 250-XXXXX 250-XXXXX Pins Glass (17) Burner Cluster Cover Ember-Glo 250-XXXXX 250-XXXXX...