Analog Devices ADP5063 User Manual
  1. Manuals
  2. Brands
  3. Analog Devices Manuals
  4. Motherboard
  5. ADP5063
  6. User manual

Analog Devices ADP5063 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the
ADP5063

FEATURES

Input voltage 4 V to 6.7 V
High current terminals for
ADP5063
(VINx), system voltage (ISO_Sx), and battery voltage
(ISO_Bx) pins
ADP5063
operation configurable via I
Evaluation software included

PACKAGE CONTENTS

ADP5063CP-EVALZ
evaluation board
Evaluation CD:
ADP5063
evaluation software installer

HARDWARE REQUIREMENTS

USB-to-serial-I/O interface
CABLEZ
is not supplied in the evaluation kit and should
be ordered separately from Analog Devices, Inc.)

SOFTWARE REQUIREMENTS

Analog Devices
ADP5063
SDP evaluation software
J8
R13
JP1
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Linear LiFePO
Compatibility in LFCSP
power connection
2
C interface
USB-SDP-CABLEZ (USB-SDP-
ADP5063
12
10
SYS _EN
J5
D2
D1
D3
13
11
TP6
D3
D2
D1
JP2
R7
R6
R5
VIN_F
D1
VIN_F
D1S
J7
J6
D2
VIN_S
D2S
R8
10
D1
14
ILED
U3
R17
ILED_S
C6
R11
GND
GND
J11
GND
GND
SDA
R15
20
R14 R1
R2
SCL
R10
C2
U1
TP5
C1
VCO _LDO
Evaluation Board User Guide
Battery Charger with Power Path and USB
4

GENERAL DESCRIPTION

The
ADP5063
evaluation board and a USB-to-serial-I/O interface
CABLEZ). All evaluation board functions and circuits are
controlled via one I
with the
ADP5063
are controlled through an on-board input/output expander
circuit on the I
3.4 V regulator for VDDIO generation. The board contains
jumpers and numerous test points for easy evaluation.
The
ADP5063CP-EVALZ
ADP5063
graphical user interface (GUI) 3.0 installer. Use the
GUI in conjunction with the
I/O interface.
Full performance details are provided in the
sheet, and the
conjunction with this user guide.
EVALUATION BOARD
14
2
7
17
VIN_S
THR
GND _S
ISO_S_S
1
8
9
16
15
ISO_B_S
TP3
R3
C12
CBP
J10
THR
TP4
R18
ISO_B_F
U2
C5
ISO_B_S
R16
ISO_B_S
ISO_S_S
BAT_SNS
TP20
ISO_S_F
C3
C4
ISO_S_F
J3
GND
THR
GND
VIN_F
ISO_S_F
J2
J1
1
Figure 1.
Rev. 0 | Page 1 of 12
charger evaluation system is composed of an
2
C bus connector. The I
directly, and the digital input/output signals
2
C bus. The evaluation board also features a
evaluation kit contains a CD with the
USB-SDP-CABLEZ
ADP5063
data sheet should be consulted in
19
GND
18
JP3
AGND
GND
GND
5
BAT_SNS
SYS _EN
SDA
SCL
16
20
BAT_SNS
ISO_B_F GND
1
UG-595
(USB-SDP-
2
C bus interfaces
USB-to-serial-
ADP5063
data

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADP5063 and is the answer not in the manual?

Questions and answers

Related Manuals for Analog Devices ADP5063

Summary of Contents for Analog Devices ADP5063

  • Page 1: Features

    USB-to-serial- USB-to-serial-I/O interface USB-SDP-CABLEZ (USB-SDP- I/O interface. CABLEZ is not supplied in the evaluation kit and should be ordered separately from Analog Devices, Inc.) Full performance details are provided in the ADP5063 data sheet, and the ADP5063 data sheet should be consulted in SOFTWARE REQUIREMENTS conjunction with this user guide.

  • Page 2: Table Of Contents

    Fast Charge Current ..............8 Evaluation Board Software .............. 3 Termination Voltage and End of Charge (EOC) Current ..8 Installing ADP5063 Evaluation Software ........3 THR Input and JEITA Settings ............9 Using the Software Graphical User Interface (GUI) ....3 Schematic Diagram ................ 10 Operating the Board with the GUI ..........

  • Page 3: Evaluation Board Software

    Complete the following steps to use the board: for the USB-SDP-CABLEZ must be installed. The software Before running the software, ensure that the Analog Devices drivers are included on the ADP5063CP-EVALZ setup CD USB-SDP-CABLEZ is plugged into the USB port of the PC.

  • Page 4: Basic Charging Parameter Settings

    After the input power supply is connected and is between 4.0 V every 0.3 second timeout from the last user action involving the and 6.7 V, the ADP5063 is operational and capable of charging GUI. When a certain interrupt is enabled, and there is a status the battery.

  • Page 5: Direct Register Read And Write

    Register R/W tab of the GUI. Type the I read only registers and cannot be overwritten. sub address in the Sub Address for READ or WRITE (0x00) Figure 4. ADP5063 Evaluation Software GUI, Register R/W Tab Rev. 0 | Page 5 of 12...

  • Page 6: Evaluation Board Overview

    VIN_F ISO_S_F R14 R1 VCO_LDO Figure 5. ADP5063 LFCSP Demo Board Typical Operation Setup The SMU at the ISO_B_F node must have a 100 mΩ to 250 mΩ TYPICAL OPERATION resistor (R ) in series with its positive lead. The resistor emulates...

  • Page 7: Input Current

    LDO (U1) and (EN_CHG), high. C input/output (I/O) expander (U2, U3A in Figure 7). The Confirm the ADP5063 charging mode: LDO generates a 3.4 V VDDIO voltage for the I C bus and •...

  • Page 8: Fast Charge Current

    Repeat Step 9 to Step 12 Simulator to evaluate different settings. ADP5063 fast charge constant voltage (CV) regulation is optimized for batteries with series resistance in the 100 mΩ to 250 mΩ range. When using a SMU or a battery simulator...

  • Page 9: Thr Input And Jeita Settings

    UG-595 THR INPUT AND JEITA SETTINGS 10. Change the trimmer resistor setting to evaluate the JEITA thresholds. The THR input resistance thresholds are The THR input of the ADP5063 evaluation board is equipped specified in the ADP5063 data sheet. with the 50 kΩ trimmer resistor (R3) and Jumper J10. When 11.

  • Page 10: Schematic Diagram

    UG-595 Evaluation Board User Guide SCHEMATIC DIAGRAM Figure 7. ADP5063 LFCSP Demo Board Schematic Rev. 0 | Page 10 of 12...

  • Page 11: Ordering Information

    20-2137 ADP1720 50 mA high voltage, micropower Analog Devices, Inc. ADP1720ARMZ-R7 linear regulator, 8-lead MSOP ADP5063 linear LiFePO battery charger with power Analog Devices, Inc. ADP5063 path and USB compatibility in LFCSP data 8-bit I C-bus I/O port with reset PCA9557PW,112 Rev.
  • Page 12 By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement.
  • Page 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc. ADP5063CP-EVALZ...

Table of Contents