Related Manuals for Raycus RFL-30QB
Summary of Contents for Raycus RFL-30QB
- Page 1 版本号 密级 内部 阶段 标记 RFL-P20QB/30QB 会签 谢良 20QB/30QB 激光器英文说明书 夏巨江 RFL-P20QB/30QB·JS02 部 门 脉冲激光器技术研究部 编 写 颜鹏晖 20210303 校 对 刘 红 20210305 审 核 李 科 20210305 标 审 李其军 20210305 批 准 黄 保 20210308 旧底图登记号 底图登记号 武汉锐科光纤激光技术股份有限公司...
- Page 2 Ytterbium Pulsed Fiber Laser User’s Guide RFL-P20QB～P30QB Wuhan Raycus Fiber Laser Technologies Co., Ltd. 2021...
- Page 3 Raycus pulsed fiber laser is classified as a high power Class IV laser device. Before supplying the power to the device, please make sure that the correct voltage of 24V DC power source is connected and the anode and cathode are right.
-
Page 4: Table Of Contents
Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB Content Description ...................... 1 1.1. Product description ......................1 1.2. Actual configuration list ....................1 1.3. Environmental requirements and cautions ..............1 1.4. Specifications ......................... 2 Mounting ...................... -
Page 5: Description
Caution: Make sure the corresponding wires of the device are properly grounded. b) All the maintenance to the device should only be done by Raycus, because there is no replacement or accessory provided with the device. Please do not try to damage the labels or open the cover in order to prevent against electric shock, or the warranty will be invalid. -
Page 6: Specifications
Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB e) Do not install the collimating device into the output head when the laser device is in working f) The device has three cooling fans at the rear panel to dissipate heat. In order to guarantee enough airflow to help giving heat off, there must be a space of at least 10cm’s width for airflow in front and rear side of the device. -
Page 7: Mounting
Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB 2. Mounting Mounting dimensions a) Fiber Laser module dimensions (As shown in Fig. 1). Figure 1. Dimension drawing of laser module (Unit: mm). b) Isolated output isolator (As shown in Fig. 2). - Page 8 Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB damaging due to vibration during the transportation. b) Fix the laser device steady on the holder and ensure good ventilation. c) The power connector of this high performance small volume laser device is DB7 dual power supply.
-
Page 9: Control Interface
Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB 3. Control Interface There are DB9 and DB25 interfaces at the rear of the laser. The DB9 is a RS232 interface only used for debugging, no needs to connect. And DB25 is the joint interface connecting control system to the laser system, please make sure the connection is reliable before operation. - Page 10 Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB in Table 4: Table 5. Definition of power control PIN value. Setting 1 Setting 2 Setting 3 Setting 4 PIN 1 PIN 2 PIN 3 PIN 4...
-
Page 11: Operation Regulations
Wuhan Raycus Fiber Laser Technologies CO., Ltd. Pulsed Fiber Laser User’s Guide V2.1 P20QB/P30QB signal must be switched ON, in other word, the signal of PIN 18 must be ahead of PIN 19 at least 5 ms, and otherwise the laser machine may be damaged. -
Page 12: Cautions
Raycus has the right to choose to repair or replace any product that proves to be defective in materials and workmanship selectively during the warranty period. Only products with particular defects are under warranty. - Page 13 If any damage happens to the product, please notify the carrier in document immediately. All the items about warranty and service above provided by Raycus are only for reference; formal contents about warranty and service are subject to the contract.