Maintenance And Repair - Dremel 200 Original Instructions Manual

rather than to do the entire job with one pass. A gentle touch
gives the best control and reduces the chance of error.
HOLDING THE TOOL
For best control in close work, grip the multitool like a pencil
ЛОЭаООЧ вШЮЫ ЭСЮЦЛ КЧН ПШЫОiЧРОЫғ PIӨTURE Қ3
TСО "РШlП" РЫТЩ ЦОЭСШН ТЬ ЮЬОН ПШЫ СОКЯТОЫ ШЩОЫКЭТШЧЬ ЬЮМС КЬ
grinding or cutting. PICTURE 14
OPERATING SPEEDS
To select the right speed for each job, use a practice piece of
material.
SLIөE "ON/OFF" SАITӨH
TСО ЭШШl ТЬ ЬаТЭМСОН "ON" Лв ЭСО ЬlТНО ЬаТЭМС lШМКЭОН ШЧ ЭСО
top side of the motor housing.
TO TURN THE TOOL "ON", ЬlТНО ЭСО ЬаТЭМС ЛЮЭЭШЧ ПШЫаКЫНғ
TO TURN THE TOOL "OFF", ЬlТНО ЭСО ЬаТЭМС ЛЮЭЭШЧ ЛКМФаКЫНғ
HIGH PERFORMANCE MOTOR
Your tool is equipped with a high performance rotary tool motor.
This motor expands the versatility of the rotary tool by driving
additional Dremel attachments.
ELECTRONIC FEEDBACK
Your tool is equipped with an internal electronic feedback
ЬвЬЭОЦ ЭСКЭ ЩЫШЯТНОЬ К "ЬШПЭ ЬЭКЫЭ", аСТМС аТll ЫОНЮМО ЭСО
stresses that occur from a high torque start. The system also
helps to keep the preselected speed virtually constant between
no-load and load conditions.
VARIABLE SPEED DIAL
Your tool is equipped with a variable speed dial. The speed
may be adjusted during operation by presetting the dial on or
between any one of the settings.
The speed of Rotary Tool is controlled by setting this dial on the
housing. PICTURE 12
SОЭЭТЧРЬ ПШЫ ӘЩЩЫШбТЦКЭО RОЯШХЮЭТШЧЬ
200 Model
Switch Settings
Low
High
3000 Model
Switch Settings
1-2
3-4
5-6
7-8
ҰҒҚ0
4000 and 4200 Model
Switch Settings
5
10
*15
20
25
30
33 (4000 only)
35 (4200 only)
* DШ ЧШt ОбМООН 15,000 RPM аСОЧ usТЧР аТrО ЛrusСОs.
Speed Range (RPM)
15,000
35,000
Speed Range (RPM)
10,000-14,000
ҚҢ,000ҒҚҰ,000
20,000-23,000
24,000-28,000
қҰ,000Ғ33,000
Speed Range (RPM)
5,000
10,000
15,000
20,000
25,000
30,000
33,000
35,000
Refer to the Speed Settings chart on pages 4-7 to help
determine the proper speed for the material being worked on
and the accessory to use.
Most jobs can be accomplished using the tool at the highest
setting. However, certain materials (some plastics and metals)
can be damaged by high-speed generated heat and should
be worked on at relatively low speeds. Low speed operation
(15,000 RPM or less) is usually best for polishing operations
employing the felt polishing accessories. All brushing
applications require lower speeds to avoid wire discharge from
the holder. Let the performance of the tool do the work for you
when using lower speed settings. Higher speeds are better for
hardwoods, metals and glass and for drilling, carving, cutting,
routing and shaping.
Some guidelines regarding tool speed:
• Plastic and other materials that melt at low temperatures
should be cut at low speeds.
PШlТЬСТЧР, ЛЮПiЧР КЧН МlОКЧТЧР аТЭС К аТЫО ЛЫЮЬС ЦЮЬЭ ЛО
•
done at speeds no greater than 15,000 RPM to prevent
damage to the brush and your material.
• Wood should be cut at high speed.
• Iron or steel should be cut at high speed.
• If a high speed steel cutter starts to vibrate, it usually
indicates that it is running too slowly.
• Aluminium, copper alloys, lead alloys, zinc alloys and tin
may be cut at various speeds, depending on the type of
МЮЭЭТЧР ЛОТЧР НШЧОғ UЬО К ЩКЫКПiЧ (ЧШЭ аКЭОЫ) ШЫ ШЭСОЫ
suitable lubricant on the cutter to prevent the cut material
from adhering to the cutter teeth.
NOTE: Increasing pressure on the tool is not the answer when
Тt Тs ЧШt pОrПШrЦТЧР prШpОrlв. Trв К НТППОrОЧt КММОssШrв Шr spООН
sОttТЧР tШ КМСТОЯО tСО НОsТrОН rОsult.

MAINTENANCE AND REPAIR

ALWAYS UNPLUG THE TOOL FROM THE
WARNING
!
POWER SOURCE BEFORE YOU MAKE
ANY ADJUSTMENTS, CHANGE ACCESSORIES, SERVICE,
ӨLEӘІ, ETӨғ THIS REөUӨES THE RISK ЇF STӘRTIІG THE
TЇЇL ӘӨӨIөEІTӘLLВғ
HAVE YOUR POWER TOOL SERVICED
WARNING
!
BY A QUALIFIED REPAIR PERSON WHO
USES ЇІLВ IөEІTIӨӘL REPLӘӨEMEІT PӘRTSғ АE
RECOMMEND THAT ALL TOOL SERVICE BE PERFORMED BY
Ә өREMEL SERVIӨE ӨEІTREғ THIS АILL EІSURE THE
SӘFETВ ЇF THE TЇЇLғ MӘIІTEІӘІӨE PERFЇRMEө әВ
UNAUTHORIZED PERSONNEL CAN RESULT IN INCORRECT
CONNECTION OF INTERNAL WIRING AND COMPONENTS
АHIӨH ӨӘІ ӨӘUSE SERIЇUS HӘГӘRөғ
NOTE
ВШu МКЧ ШЧlв ТЧspОМt КЧН rОplКМО tСО МКrЛШЧ ЛrusСОs. TСОrО
КrО ЧШ ШtСОr sОrЯТМОКЛlО pКrts ТЧsТНО tСО tШШl.
1. Clean ventilation openings, switch and levers of the tool
with compressed dry air.
DO NOT CLEAN THE TOOL BY
WARNING
!
INSERTING POINTED OBJECTS
THRЇUGH ӘІ ЇPEІIІGғ
WEAR SAFETY GOGGLES TO PROTECT
WARNING
!
ВЇUR EВESғ
2. Clean the surface of the tool with a damp cloth.
21
CLEANING