Download Print this page

Specification; Installation - Sealey AB2050 Quick Start Manual

205,000btu/hr space warmer kerosene/ diesel heater with wheels

Advertisement

8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT touch the heater outlet or dome when first switched off as these are very hot and will take time to cool.
Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
9
8
DO NOT unplug the heater to switch it off. Use the ON/OFF switch.
WARNING! Improper maintenance can lead to poor combustion and soot production
WARNING! IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.
CONTACT THE MANUFACTURER.
This appliance is not intended for persons (including children) with reduced physical, sensory or mental capabilities, or lack of
NOTE:
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
205,000Btu/hr(60kW) Heat output. Clean burning and proven pump system can operate with either kerosene or diesel. Stainless steel
combustion chamber. Can be thermostatically controlled to desired temperature. Fitted with safety cut-outs and fuel gauge. Features sturdy
handle and heavy-duty wheels for easy manoeuvrability Complies with rigorous standards.

3. SPECIFICATION

Model no.
Airflow (cfm)
Electrical fuse rating
Electrical Plug type
Fuel
Fuel tank
Heated area
Motor power
Output
Running time per filling (max.)
Supply
Transport wheels
4. ASSEMBLY
4.1.
Remove heater from carton.
4.2.
If unit is damaged in any way DO NOT use and contact the Supplier.
Insert the wheel shaft E into the corresponding hole of the caster fixing plate J.
4.3.
Insert the cotter I to the corresponding holes of the wheel shaft.
Fit plain washer F to the two sides of shaft, slide the wheel D over the wheel shaft E.
Screw the nut G to fix the wheel on the shaft.
Install the wheel cover H.
Use the clamping screw C and Plain washer ø6 B to install the Handle A into the corresponding
hole of the caster fixing plate J.
5.

INSTALLATION

5.1.
Position the heater on a flat, level, non-flammable, solid surface.
5.2.
Direct-fired heaters are intended for use in outdoor open areas or in indoor well ventilated areas. For indoor use, provide permanent
ventilation openings of at least 25 cm²/kW, equally distributed between floor and high level, with a minimum of 250 cm².
Maximum Opening Size:
AB2050: 1400cm²
9
Only install the heater in normal upright position.
8
DO NOT place the heater near walls, corners or low ceilings.
8
DO NOT place the heater below a socket outlet.
8
DO NOT place the heater on moving vehicles or where it can tip over.
Keep the heater away from flammable, combustible, explosive or corrosive materials.
9
9
Keep the heater away from curtains or similar materials that could block the air inlet and outlet.
9
Never block or restrict the air inlet and outlet for any reason.
9
Keep the power cable away from heat sources, sharp edges, cutting and moving parts.
8
DO NOT expose directly to the weather or to excessive humidity.
8
DO NOT place the heater in the immediate surroundings of a bath, shower or swimming pool.
5.3.
Follow general and special fire safety regulations in force in all fields of applications. In any case ensure the following minimum safety
clearances from materials or objects in the surroundings of the heater:
Side: 0.6 m Air inlet side: 1 m Top: 1.5 m Hot air outlet side: 3 m Floor: 0 m
5.4.
Floors and ceilings must be made of fireproof materials in the place where the heater is operated.
8
DO NOT connect direct-fired heaters to air ducts
© Jack Sealey Limited
fig.1
AB2050
700
13A
3-pin BS
Kerosene/Diesel
56L
56,500ft³(1,600m³)
340W
205,000Btu/hr(60kW)
10hr
230V~50Hz
Yes
Original Language Version
No.
Description
A
Handle
B
Plain washer Ø6mm
C
Clamping screw
D
Wheel
E
Wheel shaft
F
Plain washer
Ø12mm
G
Nut M12
H
Wheel cover
I
Cotter pin
J
Castor fixing plate
AB2050 Issue:1 06/04/22
Qty.
1
4
4
2
1
2
2
2
2
2

Advertisement

loading