Advertisement
1.3.
POSITIONING OF HEATER
WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.
‰
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
8
DO NOT place the heater up against any surface such as a wall, door or furniture etc.
8
DO NOT place the heater immediately below any electrical outlet.
8
Position the heater at least a minimum of 0.5mtr at the rear and sides, and 2m at the front, from any walls or objects.
9
DO NOT place the heater on a raised surface or anywhere where it could topple over.
8
DO NOT get the heater wet or use in areas of high condensation.
8
DO NOT allow the power lead to touch hot surfaces.
8
DO NOT connect the heater to a timer device or other equipment than can automatically switch the heater on or off.
8
If an extension cable is required it must be of the same cross section as the heater cable. It must be as short as possible and fully
9
unwound.
DO NOT connect other appliances to the same mains socket as the heater.
8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT stand on the heater.
8
DO NOT use the heater with wet hands or when there is water on the power cord.
8
Ensure that the heater is correctly turned off when not in use and store in a safe, dry, childproof location.
9
DO NOT use the heater for anything other than its intended purpose. It is designed to provide heat in enclosed areas larger than 4m³,
8
such as workshops and other industrial areas. It is not suitable for drying clothes or laundry.
1.4.
OPERATIONAL PRECAUTIONS
The heater must only be used by people who have read these instructions and have been trained in its use.
9
DO NOT obstruct the air inlet and outlet sections of the heater.
8
DO NOT cover the heater.
8
DO NOT touch the heater casing or grille when first switched off, as these will be very hot and will take time to cool.
8
NOTE: Children of less than 3 years should be kept away unless supervised continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and
vulnerable people are present.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
2. INTRODUCTION
Electric fan heaters for industrial applications. Model No's EH5001, EH9001 and EH30001 feature two heat settings and fan only option.
Model No. EH15001 features three heat settings and adjustable thermostat control with fan only option. Auto cooling system to prevent
unit from overheating during use. A totally dry heat with no condensation, no gas, no fumes and no smell. Ideal for workshops and
garages. Model No's EH5001 and EH9001 supplied with 3-phase power cable and 16A plug. Model No's EH15001 and EH30001
supplied with 3-phase chassis mounted 5-pin connector (extension cable required).
3. SPECIFICATION
Model No:......................................... EH5001................................................EH9001..............................................EH15001
IP Class:.................................................IPX4.....................................................IPX4.....................................................IPX4
Max. Power:........................................5000W..................................................9000W...............................................15000W
Supply:............................................415V-16A.............................................415V-16A............................................415V-32A
Heat Settings:.............................2500/5000W.........................................4500/9000W...........................5000/10000/15000W
Btu/hr...................................................17,000..................................................31,000.................................................51,000
Self Resetting-
Thermostat:.......................................0 - 40ºC................................................0 - 40ºC................................................0 - 40ºC
Size (mm):................................315x330x400........................................350x405x460.......................................495x520x860
IMPORTANT!
This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the front of the
heater will be warmer than the general temperature of the room, but there may not be a significant increase owing to the large
volume of air passing over the element. For the same reason, the element is hot during operation, but does not glow. The room
temperature depends on room size, insulation and ambient temperature, which will increase as the room warms.
4. ASSEMBLY (EH15001 ONLY)
4.1.
ASSEMBLY OF THE LEGS. (fig.1)
4.1.1.
On either side of the heater body there are two threaded inserts (B) for mounting the 'V' shaped leg frames (A). Note that the axle hole
at the shorter end of the 'V' frames should be orientated towards the back of the heater.
4.1.2.
Take two M8 x 40mm bolts (D) and slide a plain washer (C) onto each one. Insert a bolt through each of the mounting holes on the leg
frame and slide a split washer (E) over each protruding bolt. Align the bolts with the two threaded inserts (B) on the heater body and
screw them down securely.
4.1.3.
Mount the other 'V' frame to the other side of the heater body in the same way.
ASSEMBLY OF THE WHEELS. (fig.2)
4.2.
4.2.1.
Take the axle rod (F) and insert it through the holes in the 'V' frames so that the threaded rod ends protrude equally either side. Retain
the axle rod in this position by inserting a split pin (G) through the holes situated just on the inside of each leg frame.
4.2.2.
Slide a plain washer (H) over each end of the axle rod, followed by a wheel (J) followed by anther plain washer (H).
4.2.3.
Screw a nyloc nut (L) onto each end of the axle by hand until it begins to bite. Hold one nut steady with a 19mm spanner and
progressively tighten each nut until it bottoms out on the thread.
4.3.
ASSEMBLY OF THE HANDLE. (fig.3)
4.3.1.
Slide a plain washer over each of the four M5 x 50mm bolts supplied.
© Jack Sealey Limited
Original Language Version
EH15001, EH9001, EH5001 Issue 9(3) 25/08/21
Advertisement
