Advertisement
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT touch the heater outlet or dome when first switched off as these are very hot and will take time to cool.
8
Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
9
DO NOT unplug the heater to switch it off. Use the ON/OFF switch.
8
‰
WARNING! Improper maintenance can lead to poor combustion and soot production
‰
WARNING! IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.
CONTACT THE MANUFACTURER.
This appliance is not intended for persons (including children) with reduced physical, sensory or mental capabilities, or lack of
NOTE:
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
35,000Btu/hr, 70,000Btu/hr Heat output Clean burning and proven pump system can operate with either kerosene or diesel. Stainless steel
combustion chamber. Dual LED Display for ambient and thermostatically controlled desired temperature. Fitted with safety cut-outs and fuel
gauge. Complies with rigorous standards.
3. SPECIFICATION
Model no.
Airflow (cfm)
Electrical fuse rating
Electrical Plug type
Fuel
Fuel tank
Heated area
Motor power
Output
Running time per filling (max.)
Supply
Transport wheels
4. ASSEMBLY
4.1.
To assemble the heater, proceed as follows (see Fig.1):
Insert the wheel shaft E into the corresponding hole of the caster fixing plate J, insert the cotter I to the corresponding holes of the
4.2.
wheel shaft; put plain washer F to the two sides of shaft, slide the wheel D over the wheel shaft E, screw the nut G to fix the wheel on
the shaft
4.3.
Install the wheel cover H.
Use the clamping screw C and Plain washer ø6 B to install the Handle A into the corresponding hole of the caster fixing plate J.
4.4.
fig.1
5.
INSTALLATION
Position the heater on a flat, level, non-flammable, solid surface.
5.1.
Direct-fired heaters are intended for use in outdoor open areas or in indoor well
5.2.
ventilated areas. For indoor use, provide permanent ventilation openings of at
least 25 cm²/kW, equally distributed between floor and high level, with a minimum of 250 cm².
Maximum Opening Size:
AB1008 - 800cm
2
AB1258, AB1758 - 1250cm
9
Only install the heater in normal upright position.
8
DO NOT place the heater near walls, corners or low ceilings.
8
DO NOT place the heater below a socket outlet.
8
DO NOT place the heater on moving vehicles or where it can tip over.
Keep the heater away from flammable, combustible, explosive or corrosive materials.
9
© Jack Sealey Limited
AB1008
AB1258
441
529
34L
28,250ft³(800m³)
42,300ft³(1,200m³)
230W
340W
100,000Btu/hr(30kW)
135,000Btu/hr(40kW)
14hr
2
Original Language Version
AB1758
647
13A
3-pin BS
Kerosene/Diesel
50L
49,500ft³(1,400m³)
170,000Btu/hr(50kW)
11hr
230V~50Hz
Yes
No.
Description
A
Handle
B
Plain washer Ø6mm
C
Clamping screw
D
Wheel
E
Wheel shaft
F
Plain washer
Ø12mm
G
Nut M12
H
Wheel cover
I
Cotter pin
Castor fixing plate
J
AB1008.V4, AB1258.V4, AB1758.V4 Issue:1 05/04/22
Qty.
1
4
4
2
1
2
2
2
2
2
Advertisement
