Table of Contents
Advertisement
Quick Links
Installation Guide
For Models:
UBW48ABZ4L
UBW48BC4L
UBW48WW4L
4009654
net weight of fan: 12.56 lb (5.7 kg)
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pg. 4
Wiring. pg. 5
Canopy Assembly. pg. 6
Blade Assembly. pg. 6
Light Kit Assembly. pg. 7
Testing Your Fan. pg. 7
Troubleshooting. pg. 8
Parts Replacement. pg. 8
Warranty. pg. 8
PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Litex Industries UBW48ABZ4L
Summary of Contents for Litex Industries UBW48ABZ4L
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Models: UBW48ABZ4L UBW48BC4L UBW48WW4L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. To prevent personal injury and damage, ensure blade edge that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. inches (76cm) from any wall or obstruction. 7 feet (76cm) This fan is suitable for room sizes up to (2.13m) 225 square feet (20.9 square meters). -
Page 5: Fan Assembly
5. Fan Assembly. 5. Fan Assembly. wood ceiling With the hanging bracket secured to joist the outlet box and able to support the fan, you are now ready to hang safety cable loop your fan. Loosen canopy set screw and lower canopy to expose hanging ball at top of downrod. -
Page 6: Wiring
6. Wiring. CAUTION: Be sure outlet box is properly white supply wire grounded and that a ground wire (GREEN or Bare) is present. black supply wire Make sure all electrical connections comply from ceiling with Local Codes or Ordinances and the black National Electrical Code. -
Page 7: Canopy Assembly
7. Canopy Assembly. Raise canopy to hanging bracket until canopy touches the ceiling. Tighten the canopy set screw to secure canopy. Carefully remove protective paper from canopy canopy set screw downrod. downrod 8. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. -
Page 8: Light Kit Assembly
9. Light Kit Assembly. Install 1 medium base 6.5 watt max. LED bulb (included). IMPORTANT: When replacing bulb, please allow bulb and glass shade to reverse switch cool before touching. Partially loosen 3 thumbscrews at bottom of motor housing and raise glass motor shade to motor housing. -
Page 9: Troubleshooting
Service at 1-800-527-1292 to arrange for return of fan. 1. Check wall switch to fan. Return fan, shipping prepaid, to Litex Industries, Ltd. We will 2. Verify that reverse switch is set completely repair or ship you a replacement fan, and we will pay the in either direction.