Table of Contents
Advertisement
Quick Links
Installation Guide
For model:
C-PB42SN5L
4009654
net weight of fan: 11.93 lb. (5.41 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Blade Assembly. pg. 4
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Light Kit Assembly. pg. 7
Testing Your Fan. pg. 7
Troubleshooting. pg. 8
Parts Replacement. pg. 8
Warranty. pg. 8
PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Litex Industries C-PB42SN5L
Summary of Contents for Litex Industries C-PB42SN5L
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For model: C-PB42SN5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Blade Assembly. pg. 4 Fan Assembly. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet that the hanging location allows the blades a (76cm) (2.13m) clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 144 square 10ft. -
Page 5: Blade Assembly
5. Blade Assembly. decorative Locate 15 blade attachment screws/washers nuts and 15 decorative nuts in one of the hardware blade arm packs. screw Take special note of labels on blades and lock washer blade arms indicating THIS SIDE UP and refer blade to drawing at right as needed for the following paragraph. - Page 6 6. Fan Assembly. (cont.) vice Remove vice from safety cable by loosening the screw and screw nut on the vice. Loosen yoke set screws and nut at top of motor housing. Tip: To prepare for threading electrical wires through electrical wiring downrod, apply a small piece of electrical tape to the ends and safety cable downrod...
-
Page 7: Wiring
7. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. white supply wire ground (green or bare) CAUTION: Be sure outlet box is properly grounded black supply wire and that a ground wire (GREEN or Bare) is present. -
Page 8: Light Kit Assembly
9. Light Kit Assembly. motor housing Install one 6.5 watt medium base LED bulb (included). IMPORTANT: When replacing bulb, please allow bulb and glass shade to cool down before touching. Align grooves on glass shade with nodules on inside edge of light kit fitter and push up gently on glass shade. -
Page 9: Troubleshooting
Service at 1-800-527-1292 to arrange for return of fan. 2. Verify that reverse switch is set completely in Return fan, shipping prepaid, to Litex Industries, Ltd. We will either direction. repair or ship you a replacement fan, and we will pay the 3.