Table of Contents
Advertisement
Quick Links
Installation Guide
For Models:
CC42BB4L
CC42WW4L
4009654
net weight of fan: 9.47 lb. (4.3 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Preparation for Wiring. pg. 4
Wiring. pg. 4
Fan Assembly. pg. 5
Motor Housing Assembly. pg. 5
Blade Assembly. pg. 6
Light Assembly. pgs. 6 - 7
Testing Your Fan. pg. 7
Troubleshooting. pg. 8
Parts Replacement. pg. 8
Warranty. pg. 8
PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Litex Industries CC42BB4L
Summary of Contents for Litex Industries CC42BB4L
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Models: CC42BB4L Table of Contents: CC42WW4L Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Preparation for Wiring. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a inches 7 feet (76cm) clearance of 7ft. (2.13m) from the floor and 30in. (2.13m) (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 144 square feet (13.4 square meters). -
Page 5: Preparation For Wiring
5. Preparation for Wiring. hook end Remove 1 motor mounting screw from hook end hanging of motor assembly. Remove the other 2 motor bracket mounting screws from hanging bracket. Save motor mounting screws for later use. Lift motor assembly to hanging bracket and slide hook end (with single screw hole) into square motor opening on hanging bracket (see diagram at... -
Page 6: Fan Assembly
7. Fan Assembly. Carefully push wiring and wire connectors into outlet box. Leave hook end of motor assembly in square opening of hanging bracket and lift the other end of motor assembly toward hanging bracket. Align motor assembly screw holes with motor hanging bracket screw holes and re-insert motor... -
Page 7: Blade Assembly
9. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. motor housing Locate 12 blade attachment screws and washers in hardware pack. Hold blade arm up to blade and align holes. Insert 3 blade attachment screws (along with washers) with blade attachment fingers first and then tighten screws securely... -
Page 8: Testing Your Fan
10. Light Assembly. (cont.) Raise glass shade to light kit plate, pushing up gently until lip on glass shade fits securely inside light kit plate. Re-tighten thumbscrews. Do not overtighten thumbscrews as glass may thumb- crack or break. Make sure that glass shade is thumbscrew screw secure by pulling down GENTLY on glass shade. -
Page 9: Troubleshooting
Problem: Fan fails to operate. Service at 1-800-527-1292 to arrange for return of fan. Solutions: Return fan, shipping prepaid, to Litex Industries, Ltd. We will 1. Check wall switch to fan. repair or ship you a replacement fan, and we will pay the 2.