Table of Contents
Advertisement
Quick Links
Federal regulations require ceiling fans
with light kits manufactured or imported
after January 1, 2009, to limit total
wattage consumed by the light kit to
190W.
Therefore, this fan is equipped
with a wattage limiting device.
Installation Guide
For Models:
E-DCF52BNK5C3
E-DCF52FBZ5C3
E-DCF52MWW5C3
E89519
net weight of fan: 15.65 lb. (7.1 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Light Kit Assembly. pgs. 7- 8
Testing Your Fan. pg. 8
Troubleshooting. pg. 9
Warranty. pg. 9
Parts Replacement. pg. 9
PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Litex Industries E-DCF52BNK5C3
Summary of Contents for Litex Industries E-DCF52BNK5C3
-
Page 1: Table Of Contents
190W. Therefore, this fan is equipped with a wattage limiting device. Installation Guide For Models: E-DCF52BNK5C3 E-DCF52FBZ5C3 E-DCF52MWW5C3 Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. Read all instructions and safety information carefully before installing your fan and save these instructions. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that inches the hanging location allows the blades a clearance 7 feet (76cm) of 7ft. (2.13m) from the floor and 30in. (76cm) from (2.13m) any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft. - Page 5 5. Fan Assembly (with downrod). If you wish to extend the hanging length of your fan, you must remove the hanging ball set screw hole set screw from the 4in. downrod provided to use with an stop pin extended downrod (sold separately). [If you wish to use the 4in.
-
Page 6: Fan Assembly. Pgs
5. Fan Assembly (with downrod). (cont. ) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket tab hanging bracket and let hanging ball rest on the hanging ball slot... -
Page 7: Wiring
7. Wiring. CAUTION: Be sure outlet box is properly grounded white supply wire ground and that a ground wire (GREEN or Bare) is present. (green or bare) black supply wire Make sure all electrical connections comply with Local Codes or Ordinances and the National from ceiling Electrical Code. -
Page 8: Blade Assembly
9. Blade Assembly. Time Saver: Washers for blade screws can be blade screw and washer set on each blade screw prior to installing blades. Locate 15 blade attachment screws and washers in one of the hardware packs. Hold blade arm up to blade and align holes. Insert 3 motor housing blade attachment screws (along with washers) with fingers first and then tighten screws... -
Page 9: Testing Your Fan
10. Light Kit Assembly. (cont.) motor housing Connect WHITE wire from switch housing to WHITE wire from light kit fitter. Connect BLACK (or BLUE) wire from switch housing to BLACK wire from light kit fitter. Be sure molex connections snap together completely. Align holes in light kit fitter with holes in switch housing. -
Page 10: Troubleshooting
Service at 1-800-527-1292 to arrange for return of fan. 2. Verify that reverse switch is set completely in Return fan, shipping prepaid, to Litex Industries, Ltd. We will repair or ship you a replacement fan, and we will pay the either direction.