Table of Contents
Advertisement
Quick Links
Installation Guide
For models:
WE52BNK5LR
WE52EB5LR
4007498
net weight of fan: 16.09 lb. (7.3 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Light Kit Assembly. pg. 7
Remote Control Operation. pg. 8
Testing Your Fan. pg. 9
Troubleshooting. pg. 10
Parts Replacement. pg. 10
Warranty. pg. 10
PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Litex Industries WE52BNK5LR
Summary of Contents for Litex Industries WE52BNK5LR
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For models: WE52BNK5LR WE52EB5LR Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet that the hanging location allows the blades a (2.13 m) (76 cm) clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft. -
Page 5: Fan Assembly. Pgs
5. Fan Assembly. If you wish to extend the hanging length of your fan, you must remove the hanging ball from the downrod provided to use with an set screw set screw hole extended downrod (sold separately). [If you wish stop pin to use the downrod provided, please proceed to instructions following the dotted line below.]... - Page 6 5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket hanging bracket tab and let hanging ball rest on the hanging bracket.
-
Page 7: Wiring
7. Wiring. WARNING: Turn off circuit breakers to current ground (green or bare) fixture from breaker panel and be sure switch is white supply wire turned to the OFF position. black supply wire ground (green CAUTION: Be sure outlet box is properly or bare) grounded and that a ground wire (GREEN or Bare) is present. -
Page 8: Blade Assembly
9. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If overtightened, blades may crack and break. Time Saver: Washers for blade screws can be set on motor housing each blade screw prior to installing blades. -
Page 9: Remote Control Operation
11. Remote Control Operation. Remote Control Bracket If you wish to use the remote control bracket, install screws, included in remote pack, through bracket and into the desired installation site. The remote control transmitter rests inside the bracket. Bracket Screws CAUTION: The remote control transmitter can be programmed to multiple receivers or fans. -
Page 10: Testing Your Fan
12. Testing Your Fan. It is recommended that you test fan before finalizing installation. Test fan speeds with the different fan speed buttons on remote control. Test the light ON/OFF function with the button on the remote control. Test dimmer motor housing function by holding down the button for... -
Page 11: Troubleshooting
Service at 1-800-527-1292 to arrange for return of fan. either direction. Return fan, shipping prepaid, to Litex Industries, Ltd. We will 3. Check to be sure fan is wired properly. repair or ship you a replacement fan, and we will pay the 4.