Related Manuals for ARTHUR HOLM AH17D3 RHDGA TALK
Summary of Contents for ARTHUR HOLM AH17D3 RHDGA TALK
- Page 1 User manual AH17D3 RHDGA TALK AH19D3 RHDGA TALK Electrically motorised monitor for furniture integration, with DynamicTalk. Horizontal and vertical working positions...
-
Page 2: Table Of Contents
Table of contents EC REGULATIONS & SECURITY SAFETY INSTRUCTIONS APPLICATIONS BOX CONTENTS FEATURES PREPARATION FOR INSTALLATION CONTROLS MONITOR OSD MENU INPUT CONNECTORS DYNAMICTALK HANDLING MONITOR AHnet PROTOCOL DYNAMICTALK AHnet PROTOCOL INPUT SIGNALS PRODUCT WARRANTY... - Page 3 Welcome Thank you for purchasing an ARTHUR HOLM product. Our product range has been designed to create the perfect meeting room, where the screens are a part of the interior design as well as essential communication tools. Please, read this installation and operating instructions carefully and keep them in a safe place for future reference.
-
Page 4: Ec Regulations & Security
EC Regulations and Security ATTENTION: Do not disassemble or modify the device in any way. This symbol warns of the presence of dangerous un-insulated voltages inside some of the components, of sufficient magnitude to expose people to risk of electronic shock. This symbol draws attention to important use and maintenance instructions in the manual that accompanies the unit. -
Page 5: Safety Instructions
Safety instructions Plugs – Do not dismantle any part of the monitor power connector – Disconnect the power plug from the AC outlet when the monitor is not going to be used for an indefinite period of time Power and extensions cords –... -
Page 6: Applications
System Description aPPlications The AH17D3 RHDGA TALK and AH19D3 RHDGA TALK systems are professional TFT displays with DynamicTalk and an electrical lift system for installation into a horizontal furniture surface. The mechanism offers both horizontal and vertical working positions. With the push of a button, the monitor is lifted. Giving it a 180 degree turn, the monitor is ready to be folded down levelled with the desk surface. -
Page 7: Features
System Description features - TFT Active Matrix display aH17d3 rHdga talK 17", widescreen format, FULL HD aH19d3 r16ga talK 19", widescreen format, FULL HD - Motorised monitor and DynamicTalk with electrical engine for furniture integration - Horizontal and vertical working positions... -
Page 8: Preparation For Installation
Preparation for Installation Before the installation of the device, please make sure to follow these steps: - Remove the two lateral transport plastic screws M8x30 on the - Remove the two front transport plastic screws M8x30... - Page 9 Preparation for Installation Follow the next steps to pack the device for a safe shipment: Dynamic3 with cover plate Dynamic3 with external control buttons Permanent press button 1 until the monitor housing gets released from the frame. Insert the two plastic screws (M8x30) entirely. To close the monitor, permanent press button 2 until the monitor housing touches the two plastic screws.
-
Page 10: Controls
Controls reMote ir control Power Switch ON/OFF the monitor Menu Activates the OSD menu on screen Cursor control up on the OSD menu down Cursor control down on the OSD menu. When the OSD menu is not active on screen, selects the input source left Cursor control left on the OSD menu... - Page 11 Controls Monitor MoVeMent controls On the upper cover plate, there are three buttons to control the up and down monitor movements and three buttons to control the DynamicTalk functions and to external control other devices (GPO): 1. Raising the monitor To rise up and tilt the monitor display, press the rear button (1) on the right hand side of the cover plate.
- Page 12 Controls 3. Retracting the monitor (downwards the screen): To fold down the monitor with the screen facing down, going into storage position, press the front button (3). This button will also turn on or off the monitor when the monitor is fully closed and the screen is facing up. It is recommended that no objects or parts of the body that could obstruct the retracting movement of the display, are not on the top of the cover plate.
-
Page 13: Monitor Osd Menu
OSD menu accessing tHe Menu systeM – With the OSD off, push the MENU button to activate the main OSD menu – Press the UP and DOWN button to move from one function to another. Please refer to the following sections below to view a complete list of all the functions available for the monitor –... - Page 14 OSD menu screen input Input signal selection DVI-A DVI 1 DVI 2 Aspect image on screen Full The image is showed on full screen 16:9 Shows the image on screen with 16:9 aspect Aspect Shows the image on full screen but keeps the original aspect ratio of the input image Shows the image on screen with 4:3 aspect Shows the image on screen with the...
- Page 15 OSD menu setuP language OSD language selection Pc control Adjusts the image on screen. Only on ARGB (analogue) input H-Pos Adjust the image on screen horizontally V-Pos Adjust the image on screen vertically Phase Adjust the phase clock Adjust the clock auto adjust Auto adjust the image on screen reset...
-
Page 16: Input Connectors
Input connectors Monitor inPut connectors dVi 1/ dVi a DVI-I input signal. Connect a DVI (digital) input signal and select DVI 1 on the OSD monitor menu. Use a DVI to VGA adapter to connect an ARGB (analogue) input signal and select DVI-A on the OSD monitor menu dVi 2 DVI-D input signal. - Page 17 Input connectors Monitor inPut connectors termination Activate (ON) the termination, ONLY on the last unit of the RS422 bus aHnet RJ45 CAT5 connector for addressable RS422 control. There is a loop through connector to use as signal RS422 output. Up to 30 monitors can be connected on the same RS422 bus USB connectors for mouse, keyboard, touch screen and WebCam.
- Page 18 Input connectors MicroPHone inPut connectors Microphone out: XLR3 microphone connector installed in the DynamicTalk 12V d.c. in: XLR4 connector to the power supply 1,2: Ground 3,4: 12Vdc GPI: SubD 9 pins female connector to contact close external functions FUNCTION Contact close of the customised push button on upper cover plate (middle button).
- Page 19 Input connectors MicroPHone inPut connectors settings: 6 dip switch to configure the DynamicTalk. DIP SWITCH FUNCTION DynamicTalk configured in PA mode. The TALK push button controls the microphone mute function off: DynamicTalk configured in conference mode. The 1,2,3 TALK push button has no function, the contact close is available on GPO connector and the LED ring is controlled externally (GPI) Factory only.
- Page 20 Input connectors MICROPHONE LENGTH SETTING PROCEDURE DynamicTalk is designed to work with microphones of different lengths. Two signs to identify an incorrect setup of the microphone length are: - The microphone do not goes down completely. - The microphone goes down too slowly and gets stuck inside. The microphone length can be adjusted using the Monitor Configurator Tool, but there is also a quick procedure that doesn’t require the use of a PC or cable:...
-
Page 21: Dynamictalk Handling
DynamicTalk Handling Please follow the figure below for a correct product usage of the DynamicTalk microphones. To avoid any product malfunctions, do not attempt to bend the microphone to the incorrect angle or outside the microphone's working area, as indicated on the picture below. Please note that ware to the microphone and pop screen surface can occur. -
Page 22: Monitor Ahnet Protocol
Monitor AHnet protocol coMMunications Protocol communication RS422 connection RJ45 wiring cat-5 sPeed & configuration Baud rate 38400 data Bits Parity None stop Bits wiring diagraM Data TX + Data TX – Data RX + Data RX - RJ-45 connection Pins 1 & 2 The units respond Pins 3 &... - Page 23 Monitor AHnet protocol aHnet Protocol Using 5 bytes communication: Byte 0 START BYTE Byte 1 ADDRESS BYTE Byte 2 COMMAND BYTE Byte 3 VALUE 1 Byte 4 VALUE2 coMMands COMMAND DESCRIPTION RESPONSE Go down, FA XX 01 00 00 FB XX 01 00 00 bottom Go up + FA XX 01 01 00...
-
Page 24: Dynamictalk Ahnet Protocol
AHnet protocol Picture coMMands COMMAND DESCRIPTION RESPONSE FA XX 15 00 00 ASK FOR BACKLIGHT LEVEL FB XX 15 00 ZZ FA XX 16 00 00 ASK FOR CONTRAST LEVEL FB XX 16 00 ZZ FA XX 17 00 00 ASK FOR BRIGHTNESS LEVEL FB XX 17 00 ZZ Number of the monitor address. - Page 25 Monitor AHnet protocol SCREEN ON SCREEN OFF DVI-A DVI 1-D DVI 2-D PROTECTION STOP MONITOR OK BUTTON LOCK BUTTON UNLOCK...
- Page 26 DynamicTalk AHnet protocol coMMunications Protocol communication RS422 connection RJ45 wiring cat-5 sPeed & configuration Baud rate 38400 data Bits Parity None stop Bits wiring diagraM Data TX + Data TX – Data RX + Data RX - RJ-45 connection Pins 1 & 2 The units respond Pins 3 &...
- Page 27 DynamicTalk AHnet protocol aHnet Protocol Using 5 bytes communication: Byte 0 START BYTE Byte 1 ADDRESS BYTE Byte 2 COMMAND BYTE Byte 3 VALUE 1 Byte 4 VALUE 2 coMMands COMMAND DESCRIPTION RESPONSE FA XX 01 01 00 GO UP FB XX 01 01 00 FA XX 01 00 00 GO DOWN...
- Page 28 DynamicTalk AHnet protocol Bite 0 TOP POSITION Bite 1 DOWN POSITION Bite 2 (1) MUTE ON Bite 3 (1) BUTTON LOCK Bite 4 Bite 5 Bite 6 Bite 7 (1) FAILURE IN THE SYSTEM To send an order to all the devices, you must use the address: F7 Hex.
-
Page 29: Input Signals
Input Signals aH17d3 rHdga talK, aH19d3 rHdga talK resolution Horizontal freq (KHz) Vertical freq (Hz) scanning type 800x600@60Hz 37.879 60.317 Progressive 800x600@72Hz 48.077 72.188 Progressive 800x600@75Hz 46.875 75.000 Progressive 1024x768@60Hz 48.363 60.005 Progressive 1024x768@70Hz 56.476 70.070 Progressive 1024x768@75Hz 60.023 75.030... - Page 30 Information on Disposal for users of waste Electrical & Electronic equipment This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
-
Page 31: Product Warranty
Product Warranty Albiral Display Solutions S.L WARRANTY - Valid from January 2016 This warranty covers the original product purchase for a period of 24 months from the date of purchase. GENERAL WARRANTY TERMS a) Parts. During the above mentioned warranty period, the replacement of any electronic and mechanical parts against any defects in manufacturing. - Page 32 Patents ES 1051718UU ES 1061088UU EP 1574150A1 ES 1068395 U WO 2009141744 Fàtima 25, Sant Hipòlit de Voltregà MU 170180 ES00 08512 Barcelona – Spain EP 2289367 A1 tel: +34 93 850 23 76 / 23 83 MU 17301 ES00 fax: +34 93 850 25 50 / 23 72 MU 17322 ES00 web: www.arthurholm.com...