Advertisement
Quick Links
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is
best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature
prior to installation.
Carefully open the carton and remove the enclosure on a large flat surface that is clean and free of dirt.
1.
Check over the parts included in the carton with the parts list shown below:
2.
Adhesive Velcro Hook Strips:
"
"
Snap Screw Studs
---------------------------------------------------------------------------
Adhesive Velcro Hook Strips:
"
"
"
---------------------------------------------------------------------------
31" Webbing Straps w/ Grommet
31" Webbing Straps w/Hook
45" Webbing Straps w/ Loop
Adhesive Velcro Hook Strips:
If any parts are damaged or missing please contact customer service at (606) 845-7439.
The cab for your Ranger is made up of 5 different components that work together to enclose your vehicle.
Install the cab in the following order.
1) Soft Doors
2) Rear Window
3) Aero-Vent Poly Windshield
4) Top Cap
Soft Doors:
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of
2009-2010 Polaris Ranger
Full Cab with Aero-Vent Poly Windshield
PO-10RANGER-FC04
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
Soft Doors
18 each------------3"
2 each------------38"
14 each ( 2 extra )
Rear Window
8 each------------3"
1 each------------30"
1 each------------55"
Top Cap
2 each
2 each
2 each
2 each------------6"
Advertisement
Related Manuals for FALCON RIDGE PO-10RANGER-FC04
Summary of Contents for FALCON RIDGE PO-10RANGER-FC04
- Page 1 2009-2010 Polaris Ranger Full Cab with Aero-Vent Poly Windshield PO-10RANGER-FC04 Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable. Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F.
- Page 2 Begin by holding the door up to the frame and attach it using the double-sided Velcro strips sewn perpendicular to the edge of the door. At each of the double-sided strips take one of the 3" adhesive Velcro strips and adhere it to the inside of the frame. Then wrap the double-sided strip around it so that the adhesive strip holds it firmly in place.
-
Page 3: Rear Window
Once all the Velcro is in place the last thing to do is install the screw snap studs. NOTE: The best way to install the snap studs is to put them in the sockets in the door first. Then push them into the plastic to make a mark. - Page 4 AERO-VENT POLYCARBONATE WINDSHIELD: Install using the directions included with the windshield. TOP CAP: After the windshield is installed take the soft Top Cap and put it over the top of the vehicle and make sure you have the on correctly. When put on correct the sides will match up with the shape of the roll cage.
- Page 5 Diagram below shows how to use ladder buckle. Now run those straps up and through the ladder lock buckles sewn to the rear of the top. You now need to tighten and loosen the strap of the top so that it is centered correctly. Cleaning and Storage Recommendations: 1.
- Page 6 Cab to either extreme hot or cold temperatures when storing. 3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
-
Page 7: Return Policy
Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors’, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition.