Table of Contents
Advertisement
Camera menu items (continued)
Others 2/5 screen
Oth ers 2 /5
Fr eeze Dur in g P re se t
Sp eed W ith Z oo m P OS .
Fo cus M ode
F ocus ADJ W it h P TZ . - -- -
Di gital Zo om
M ax Di git al Z o om
D igita l E xt en d er
IS
Re turn
Freeze During Preset [Off, On]
Turn the function for freezing images during preset playback off/on.
When this is set to [On], preset playback is performed with a still
of the image immediately preceding the start of preset playback
being output. The image freeze is released when preset playback is
finished.
Speed With Zoom POS. [Off, On]
"Off" or "On" is set here for the function used to adjust the pan-tilt
adjustment speed in conjunction with the zoom magnification.
When [On] is set, the panning and tilting operations will become
slower in the zoom status.
This function has no effect during preset operations.
Focus Mode [Auto, Manual]
Select auto or manual mode for the focus adjustment function.
Auto
Always adjust focus automatically.
Manual
Adjust focus manually.
<NOTE>
• [Focus Mode] cannot be set to [Auto] when [Frame Mix] is set to
[18dB] or [24dB].
Focus ADJ With PTZ. [Off, On]
"Off" or "On" is set here for the function which compensates for out-of-
focusing when it occurs during panning, tilting or zooming operations.
When [Off] is set, adjust the focus as required after zooming or set
the focus to the auto mode.
This item can be selected only when [Manual] has been selected as
the [Focus Mode] setting.
Digital Zoom [Disable, Enable]
"Disable" or "Enable" is set here for the digital zoom function.
If zooming is performed toward the Tele end beyond the maximum
position when [Enable] has been selected, the digital zoom can be
operated continuously. Zooming will stop temporarily at the position
where the optical zoom and digital zoom are switched so after it has
stopped at this position, proceed with zooming again.
When the setting is changed to [Disable] while already in the digital
zoom region, the zoom will automatically move to the maximum
position of the optical zoom.
Max Digital Zoom
[x2, x3, x4, x5, x6, x7, x8, x9, x10]
Set the maximum digital zoom magnification.
<NOTE>
• Higher digital zoom magnifications will result in coarser images.
Digital Extender [Off, On]
Turn the digital extender function off/on.
When this is set to [On], the digital zoom will be fixed at 1.4x.
When [Digital Zoom] is set to [Enable], [Digital Extender] is disabled.
Of f
O n
A ut o
D i sa bl e
- -- -
Of f
Of f
49
IS [Off, OIS, Dynamic I.S. System]
Select the image stabilization mode.
Off
Do not perform image stabilization.
OIS
Perform optical image stabilization (OIS).
Dynamic I.S.
Perform pan/tilt mechanism system image stabilization in
System
addition to optical image stabilization.
<NOTE>
• The optical image stabilization functionʼs level of correction is
reduced during pan/tilt operations.
Return
Return to the previous menu level.
Others 3/5 screen
O t h e r s 3 / 5
O S D M i x
S D I O u t
I P
O S D O f f W i t h T a l l y
O S D S t a t u s
D C O u t
R e t u r n
OSD Mix
Select whether to turn off/on camera menu, status, and other displays
for each output image.
SDI Out [Off, On]
IP [Off, On]
The camera menus and statuses are not displayed on the
Off
output pictures targeted by the setting items.
The camera menus and statuses are displayed for the output
On
pictures covered by the setting items.
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 2 minutes after the unit is turned on.
OSD Off With Tally [Off, On]
Off or on the function that turns off camera menu, status, and other
displays when tally signals are received via commands or contacts.
When the tally signal releases, the camera menu display will return.
OSD Status [Off, On]
Turn the status display during AWB and ABB off/on.
DC Out [Off, On]
Turn power supply output from the unit off/on.
Return
Return to the previous menu level.
O n
O n
O f f
O f f
O n
Advertisement
Table of Contents
