Specifications - Panasonic AW-HR140 Operating Instruction

Specifications

Power requirements: DC (
DC (
Current consumption: 5.5 A – 3.1 A (DC IN connector)
1.2 A (PoE++ power supply)
indicates safety information.
GENERAL
„ z
Ambient operating temperature:
–15 °C to 45 °C (5 °F to 113 °F) (preheating is
required when –5 °C (23 °F) or less)
Ambient operating humidity:
10% to 100% (no condensation)
Storage temperature:
–20 °C to 55 °C (–4 °F to 131 °F)
Storage humidity:
10% to 95% (no condensation)
Mass:
Approx. 9.0 kg (19.84 lb)
Dimensions (W x H x D):
258 mm × 357 mm × 397 mm
(10-5/32 inches x 14-1/16 inches x 15-5/8 inches)
( including protrusions and cable cover)
Finish: Silver, salt resistant coating
Waterproof and dust proof:
IP65 compliant
Maximum permissible wind speed:
15 m/sec: Operates normally
50 m/sec: Operation possible
60 m/sec: No damage
Wiper:
Installed as standard
Heater:
Installed as standard
Defroster:
Installed as standard
Controller supported:
AW-RP50, AW-RP120, AK-HRP200
• It may be necessary to upgrade the version of the
controller in order to support the unit. For details on
upgrading, visit the support page on the following
website.
http://pro-av.panasonic.net/
INPUT
„ z
Input connector
12V IN: XLR connector
• Use a DC cable with the following lengths.
For 12 V input: Max. 3 m (9.84 ft) (when using an
AWG16 cable)
For 21.8 V input: Max. 20 m (65.62 ft) (when using
an AWG16 cable)
G/L IN:
BNC connector
• BBS (Black Burst Sync), tri-level sync supported
• Locking to a subcarrier is not possible with BBS.
Audio input:
mini XLR connector (line input)
#1: INPUT1 COMMON, #2: INPUT1 HOT,
#3: INPUT1 COLD, #4: INPUT2 COMMON,
#5: INPUT2 HOT, #6: INPUT2 COLD
) 12 V – 21.8 V (DC IN connector)
) 42 V – 57 V (PoE++ power supply)
OUTPUT
„ z
Video output
HD-SDI OUT:
SMPTE424/SMPTE292 standards
75 Ω (BNC×2)
• OSD output is possible from the SDI OUT 1/PM
connector but not from the SDI OUT 2 connector.
INPUT/OUTPUT
„ z
Input/Output connector
LAN: LAN connector for IP control/video output/PoE++
power supply
PoE++ (IEEE802.3bt Draft ver.2.0 standard)
RS-422: CONTROL IN RS-422A
EXT: 12 V/0.5 A DC
#1: DC GND, #2: HOT, #3: COLD, #4: 12V-OUT
• The maximum cable length for connections to pin
number 4 [12V-OUT] is 0.5 m (1.64 ft) when using
an AWG24 cable.
Use a thicker cable when a greater length is
required.
FUNCTIONS AND PERFORMANCE
„ z
[Camera unit]
Imaging sensors: 1/2.86-type Full-HD 3MOS
Lens: Optical 20x zoom/10× digital zoom, F1.6 to F3.4
(f=4.5 mm to 90 mm; 35 mm equivalent: 32.13 mm
to 642.5 mm)
Focus: Switching between auto and manual
Focus distance: Entire zooming range: 800 mm (2.62 ft)
Wide end: 400 mm (1.31 ft)
Color separation optical system:
3MOS
Minimum illumination:
2 lx (50 IRE, F1.6, 36 dB, without accumulation)
Horizontal resolution:
1000 TV lines Typ (Center area)
Gain selection:
Auto, 0 dB to 42 dB (1 dB steps)
37 dB to 42 dB is Super Gain Mode
Frame mix: 0 dB, 6 dB, 12 dB, 18 dB, 24 dB
• This cannot be configured when the format is
1080/29.97p, 1080/23.98p, 1080/29.97PsF,
1080/23.98PsF, 1080/25p, or 1080/25PsF.
• When [Iris Mode] or [Focus Mode] is set to [Auto],
this cannot be set to 18 dB or 24 dB.
Electronic shutter speed:
• 59.94p/59.94i:
1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
• 29.97p:
1/30, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
• 23.98p:
1/24, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
• 50p/50i:
1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000
• 25p:
1/25, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
118