Operations On The Aw-Rp50 Remote Camera Controller - Panasonic AW-HR140 Operating Instruction

Basic setup operations (continued)

Operations on the AW-RP50 Remote Camera Controller

POWER ALARM
MENU PAGE
STORE DELETE
IRIS AUTO
TELE
ZOOM
WIDE
Camera menu operation
„ z
1.
Press the appropriate <CAMERA STATUS/SELECTION>
button to select the unit you want to operate.
2.
Press and hold the <CAMERA OSD> button on the
AW-RP50 for about 2 seconds.
The AW-HR140 camera menu appears on the monitor.
3.
Turn the <F1> dial to select an AW-HR140 camera menu
item or to change a setting value.
Turn the <F1> dial to move the cursor up and down or to change
setting values.
Press the <F1> dial to move to the next level of a menu item or to
change a blinking setting value at the lowest level.
4.
To exit the camera menu, press and hold the <CAMERA
OSD> for about 2 seconds.
Switching between day and night mode
„ z
1.
Press the <MENU> button on the AW-RP50.
The <MENU> button lights, and the <PRESET MEMORY/MENU>
buttons become selectable.
2.
Press the <9 (SETUP)> button in the <PRESET MEMORY/
MENU> area.
The button lights, and the [SETUP] menu appears on the LCD panel.
3.
Turn the <F1> dial to select [FUNCTION], then press the
<F1> dial.
4.
Turn the <F1> dial to select [OPTION].
[Off] or [On] appears on the bottom right (F2 area) of the LCD panel.
5. Turn the <F2> dial to select [Off] or [On], then press the
<F2> dial.
Off: Day mode
On: Night mode
1 2 3 4
GAIN/PED R/B GAIN R/B PED AWB/ABB
6 7 8 9
DETAIL SCENE/MODE CAMERA SETUP
PRESET MEMORY / MENU
1 2 3 4
CAMERA STATUS / SELECTION
AUTO
LOW
FOCUS/PUSH OAF PTZ/FOCUS SPEED
Selects a camera to be operated.
F1
F2
F1 CAMERA
OSD
5
F2 EXIT
SHUTTER
10
SYSTEM USER1 USER2
5
PT ACTIVE
HI
Color temperature setting (COLOR TEMP)
„ z
1.
Press the <MENU> button on the AW-RP50.
The <MENU> button lights, and the <PRESET MEMORY/MENU>
buttons become selectable.
2.
Press the <4 (AWB/ABB)> button in the <PRESET
MEMORY/MENU> area.
The button lights, and the [AWB/ABB] menu appears on the LCD
panel.
3.
Turn the <F1> dial to select [VAR].
Color temperature configuration is enabled when [VAR] is selected,
and it is initially set to the color temperature held on the camera.
To adjust the setting, proceed to the following.
4. Press the <8 (CAMERA)> button in the <PRESET
MEMORY/MENU> area.
The button lights, and the [GROUP] menu appears on the LCD panel.
5.
Turn the <F1> dial to select [COLOR TEMP], then press
the <F1> dial.
The color temperature appears on the bottom right (F2 area) of the
LCD panel.
6.
Turn the <F2> dial to select the color temperature, then
press the <F2> dial.
31
For operating the camera menus.
CAMERA OSD:
When this is pressed for 2
seconds, the selected camera
menu is displayed, overlapping
the camera output image. When
it is pressed for 2 seconds while
a camera menu is displayed, the
menu is exited.
F1: Turn to move the cursor up and
down in the camera menu or to
change setting values. Press to
move to the next level of a menu
item or to change a setting value
at the lowest level.