Download
Share
Print this page
SIIG JU-P40212-S1 Quick Installation Manual
  1. Manuals
  2. Brands
  3. SIIG Manuals
  4. Cables and connectors
  5. JU-P40212-S1
  6. Quick installation manual

SIIG JU-P40212-S1 Quick Installation Manual

Dp usb 3.0 4-port pcie i/e
Hide thumbs

Advertisement

Quick Links

Download this manual
Introduction
The DP USB 3.0 4-Port PCIe i/e adds four USB 3.0
ports (1 internal & 3 external) to your
PCIe-enabled desktop PC enhancing existing
systems with SuperSpeed USB 3.0 technology.
Key Features and Benefits
•
Supports data transfer rate up to 5Gb/s
and backward compatible with previous
versions of USB devices
•
Compliant with Universal Serial Bus 3.0
Specification
•
Compliant with PCI Express Base
Specification, Revision 2.1
•
Supports per port over-current protection
System Requirements
•
Desktop PC with an available PCIe slot
04-0728B
DP USB 3.0 4-Port PCIe i/e
Quick Installation Guide
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the JU-P40212-S1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SIIG JU-P40212-S1

Summary of Contents for SIIG JU-P40212-S1

  • Page 1 DP USB 3.0 4-Port PCIe i/e Quick Installation Guide Introduction The DP USB 3.0 4-Port PCIe i/e adds four USB 3.0 ports (1 internal & 3 external) to your PCIe-enabled desktop PC enhancing existing systems with SuperSpeed USB 3.0 technology. Key Features and Benefits •...

  • Page 2: Package Contents

    • Windows 8 (32-/64-bit) / Windows 7 (32- ® /64-bit) / Vista (32-/64-bit) / Server 2008 R2 / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) Package Contents • DP USB 3.0 4-Port PCIe i/e adapter • Spare low profile bracket •...
  • Page 3 Layout Power Connector USB 3.0 Port (optional)* USB 3.0 Port Figure 1: Board Layout *Note: This power connector is designed to provide additional power to the board when needed. Connect this power connector only if one or both of the following conditions occur: - Device(s) not being detected - All ports are used at the same time...

  • Page 4: Hardware Installation

    Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer's reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer's case for a few seconds.

  • Page 5: Driver Installation

    Carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the board down firmly, but gently, until it is well seated. Replace the slot bracket holding screw to secure the card. Replace the computer cover and reconnect the power cord.
  • Page 6 At the TI USB3 Host Driver - Installshield Wizard, click Next. Select I accept the terms of the license agreement, click Next, then click Finish. Restart the computer. Windows Vista (32-/64-bit) Install the board and boot up Windows. At the Found New Hardware, click Cancel. Insert the driver CD, close the Windows Explorer screen when displayed.
  • Page 7 Windows XP (32-/64-bit) / Server 2003 & 2008 Install the board and boot up Windows. At the Found New Hardware Wizard, click Cancel. Insert the driver CD. Click Start, Run. Type D:\Setup.exe, click OK. (Change D: to match your CD\DVD-ROM drive letter) At the TI USB3 Host Driver - Installshield Wizard, click Next.
  • Page 8 To Verify Windows Installation Go to Device Manager to verify installation. For Windows 8/ Windows 7 / Windows XP / Server 2008 R2 / Server 2003: Right click Computer or My Computer, click Manage, click Device Manager. For Windows Vista: Right click Computer, click Manage, click Continue, then click Device Manager.
  • Page 9 Blank Page...
  • Page 10 Blank Page...

  • Page 11: Technical Support And Warranty

    Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued.
  • Page 12 Fremont, CA 94538-3152, USA Phone: 510-657-8688 DP USB 3.0 4-Port PCIe i/e is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are for identification only and may be trademarks of their respective owners.