English Limited Warranty; Owner's Manual - Bowers & Wilkins XTC Owner's Manual And Warranty

English
Limited Warranty
Dear customer,
Welcome to B&W.
This product has been designed and
manufactured to the highest quality
standards. However, if something does go
wrong with this product, B&W Group and
its national distributors warrant free of
charge labour (exclusion may apply) and
replacement parts in any country served by
an official B&W distributor.
This limited warranty is valid for a period of
five years from the date of purchase or two
years for electronics including amplified
loudspeakers.
Terms and Conditions
1 The warranty is limited to the repair of
the equipment. Neither transportation,
nor any other costs, nor any risk for
removal, transportation and installation
of products is covered by this warranty.
2 This warranty is only valid for the
original owner. It is not transferable.
3 This warranty will not be applicable in
cases other than defects in materials
and/or workmanship at the time of
purchase and will not be applicable:
a. for damages caused by incorrect
installation, connection or packing,
b. for damages caused by any use other
than correct use described in the user
manual, negligence, modifications, or
use of parts that are not made or
authorised by B&W,
c. for damages caused by faulty or
unsuitable ancillary equipment,
d. for damages caused by accidents,
lightning, water, fire heat, war, public
disturbances or any other cause
beyond the reasonable control of B&W
and its appointed distributors,
e. for products whose serial number has
been altered, deleted, removed or
made illegible,
f. if repairs or modifications have been
executed by an unauthorised person.
4 This guarantee complements any
national/regional law obligations of
dealers or national distributors and
does not affect your statutory rights as
a customer.
How to claim repairs under
warranty
Should service be required, please follow
the following procedure:
1 If the equipment is being used in the
country of purchase, you should
contact the B&W authorised dealer from
whom the equipment was purchased.
2 If the equipment is being used outside
the country of purchase, you should
contact B&W national distributor in the
country of residence who will advise
where the equipment can be serviced.
2
You can call B&W in the UK or visit our
web site to get the contact details of
your local distributor.
To validate your warranty, you will need to
produce this warranty booklet completed
and stamped by your dealer on the date of
purchase. Alternatively, you will need the
original sales invoice or other proof of
ownership and date of purchase.

Owner's manual

Introduction
Thank you for choosing B&W.
Please read this manual fully before
unpacking and installing the product. It will
help you to optimise its performance.
B&W maintains a network of dedicated
distributors in over 60 countries who will be
able to help you should you have any
problems your dealer cannot resolve.
Unpacking
Check in the carton for:
• 2 Foam plugs
• Support/wall bracket assembly
• M6 cap head screw
• Profiled washer
• 5mm Allen key
• 2 Mounting templates
Positioning
Home theatre front centre
(figure 1)
Position the speaker in horizontal
orientation either immediately above or
immediately below the screen, depending
on which is nearer ear height.
Mounting
The speaker may be mounted on a shelf or
bookcase, or on the wall.
Stray magnetic fields
The speaker drive units are magnetically
shielded to reduce the risk of picture
distortion with CRT televisions and
computer screens. LCD and plasma
screens are not affected by magnetic fields.
Mounting on a shelf or bookcase
The wall bracket assembly consists of a
wall plate to which is attached a 'wave'
shape cover. This cover acts as the support
for the speaker when mounted on a shelf
or bookcase.
Disassemble the two parts by sliding one
against the other before pulling them apart.
Attach the 4 self-adhesive clear rubber
strips from the bracket kit to the underside
of the wave shape cover as shown in
figure 2.
If you wish to tilt the speaker upwards, the
thicker part of the support should be
positioned towards the front of the speaker.
Otherwise, position the thicker part to the
rear. (figure 3)
Mounting on the wall
We strongly recommend two people for the
final part of this job, one to hold the
speaker and the other to feed and connect
the cable.
If you are running cable in the wall, the
bracket can also disguise the cable
between its exit from the wall and the
speaker terminals, but only if the cable is
flexible enough. It is difficult to recommend
a definite maximum gauge, because cables
vary significantly in flexibility, depending on
the insulation material. Solid core cable is
not recommended because of its lack of
flexibility and tendency to fracture when
bent sharply. 4mm 2 or 10AWG is probably a
practical maximum and, if the two insulated
cores have an additional, common outer
sheath, this should be removed from close
to the wall exit.
You should determine and mark the
position of the wall plate, and therefore the
correct exit point of the cable from the wall,
before routing the cable.
The wall bracket assembly consists of a
wall plate to which is attached a 'wave'
shape cover. Disassemble the two parts by
sliding one against the other before pulling
them apart. Note that in use, the two parts
may be required to mate in a different
orientation from that supplied.
There are two mounting templates (up tilt
and down tilt), because the wall plate is
offset from the centre line of the speaker.
Furthermore, the wall bracket supplied
allows the speaker to swivel through
30 degrees, but only towards the opposite
side to the thicker part of the wall plate.
(figure 4)
The templates show the position of the wall
plate in relation to the outline of the
speaker when facing at right angles to the
wall (i.e. not tilted).
Using a spirit level, offer the appropriate
template to the wall with the outline in the
in the desired position of the speaker and
mark 4 screw positions through the marked
slots. Drill and plug the wall for 4mm (No.8)
screws. If running cable in the wall, the exit
clearance hole should be positioned as
shown by the shaded area on the template.
Run the cable in the wall if desired. If the
wall is drywall construction, leave
approximately 30cm (1 ft) of cable
protruding from the wall. Excess cable may
be pushed back into the wall void as the
speaker is mounted. If the cable is chased
into solid wall construction, the excess has
to be accommodated behind the 'wave'
cover, so it is better to trim the cable to no
more than 15cm (6 in).
Screw the wall plate to the wall in the
orientation shown in figure 5.
Attach the 4 self-adhesive clear rubber strips
from the bracket kit to the underside of the
wave shape cover as shown in figure 2.
Attach the wave cover to the back of the
speaker using an M6 screw and profiled
washer. (figure 6) The thicker side of the
'wave' cover should be positioned on the
opposite side to the direction of tilt (ie to
the bottom for upward tilt and to the top
for downward tilt. (figure 4)