Daikin Altherma EPGA16DAV3 Installer's Reference Manual page 92

Field settings table
Breadcrumb Field code Setting name
9.1 [0-03] Low ambient temp. for LWT add zone heating WD curve.
9.1 [0-04] Leaving water value for high ambient temp. for LWT add zone cooling WD curve.
9.1 [0-05] Leaving water value for low ambient temp. for LWT add zone cooling WD curve.
9.1 [0-06] High ambient temp. for LWT add zone cooling WD curve.
9.1 [0-07] Low ambient temp. for LWT add zone cooling WD curve.
└─ Tank
9.1 [6-0D] Heat up mode
9.1 [6-0A] Comfort setpoint
9.1 [6-0B] Eco setpoint
9.1 [6-0C] Reheat setpoint
└─ Domestic hot water
9.2.1 [E-05] Domestic hot water
[E-06]
[E-07]
9.2.2 [D-02] DHW pump
9.2.4 [D-07] Solar
└─ Back up heater
9.3.1 [E-03] BUH type
9.3.2 [5-0D] Voltage
9.3.3 [4-0A] Configuration
9.3.4 [6-03] Capacity step 1
9.3.5 [6-04] Additional capacity step 2
9.3.6 [5-00] Equilibrium
9.3.7 [5-01] Equilibrium temperature
9.3.8 [4-00] Operation
└─ Booster heater
9.4.1 [6-02] Capacity
9.4.3 [8-03] BSH eco timer
9.4.4 [4-03] Operation
Installer settings
9.5 [4-06] Emergency
└─ Balancing
9.6.1 [5-02] Space heating priority
9.6.2 [5-03] Priority temperature
9.6.3 [5-04] Offset BSH setpoint
9.6.4 [8-02] Anti-recycle timer
9.6.5 [8-00] Minimum running timer
9.6.6 [8-01] Maximum running timer
9.6.7 [8-04] Additional timer
Installer settings
9.7 [4-04] Water pipe freeze prevention
└─ Benefit kWh power supply
9.8.1 [D-01] Benefit kWh power supply
9.8.2 [D-00] Allow heater
9.8.3 [D-05] Allow pump
└─ Power consumption control
9.9.1 [4-08] Power consumption control
9.9.2 [4-09] Type
9.9.3 [5-05] Limit
9.9.4 [5-05] Limit 1
(*1) *6V_(*2) *9W_
(*3) + EKHVCONV2_
(*4) EAVZ16S18*_(*5) EAVZ16S23*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/W
R/W
R/O
R/W (*1)
R/O (*2)
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/W
R/W
R/O
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
-40~5°C, step: 1°C
-10°C
[9-07]~[9-08]°C, step: 1°C
8°C (*3)
[9-07]~[9-08]°C, step: 1°C
12°C (*3)
25~43°C, step: 1°C
35°C (*3)
10~25°C, step: 1°C
20°C (*3)
0: Reheat only
1: Reheat + sched.
2: Scheduled only
30~[6-0E]°C, step: 1°C
60°C
30~min(50, [6-0E])°C, step: 1°C
45°C
30~min(50, [6-0E])°C, step: 1°C
45°C
3: Integrated
0: No
1: Secondary rtrn
2: Disinf. Shunt
0: No
1: Yes
3: 6V (*1)
4: 9W (*2)
0: 230V, 1~ (*1)
1: 230V, 3~ (*1)
2: 400V, 3~ (*2)
1: 1/1+2 (*1) (*2)
2: 1/2
3: 1/2 + 1/1+2 in emergency
0~10kW, step: 0,2kW
2kW (*1)
3kW (*2)
0~10kW, step: 0,2kW
4kW (*1)
6kW (*2)
0: Allowed
1: Not allowed
-15~35°C, step: 1°C
0°C
0: Disabled
1: Enabled
2: Only DHW
0~10kW, step: 0,2kW
0kW
20~95 min, step: 5 min
50 min
0: Restricted
1: Allowed
2: Overlap
3: Compressor off
4: Legionella only
0: Manual
1: Automatic
0: Disabled
1: Enabled
-15~35°C, step: 1°C
0°C
0~20°C, step: 1°C
10°C
0~10 hour, step: 0,5 hour
0,5 hour
0~20 min, step 1 min
1 min
5~95 min, step: 5 min
30 min
0~95 min, step: 5 min
95 min
0: Intermittent
0: No
1: Active open
2: Active closed
3: Safety thermostat
0: None
1: BSH only
2: BUH only
3: All heaters
0: Forced off
1: As normal
0: No limitation
1: Continuous
2: Digital inputs
0: Current
1: Power
0~50 A, step: 1 A
50 A
0~50 A, step: 1 A
50 A
5/10
Installer setting at variance with
default value
Date Value
4P556077-1 - 2018.12