Keep this manual available to all personnel. All specifications are nominal and may change as design improvements occur. Greenlee Textron Inc. shall not be liable for Do not discard this product or throw away! damages resulting from misapplication or misuse of its products.
This tool is not insulated. When using this unit on or near energized electrical lines, use proper personal protective equipment. Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 4
• Use only Greenlee punches, dies, and draw studs. Other manufacturers’ components might not with- stand the forces generated by this punch driver. Failure to observe these warnings could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 5
• Do not place a battery on moist ground or grass. Moisture may create a short circuit and damage the battery. Failure to observe these precautions may result in injury or property damage. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Tool will stop, and flashing 20 A during cycle light for 20 seconds when head when punching. trigger is released Circuit has become too hot Failure to observe these warnings could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 8
9. Pull the trigger. The LS50L2 will automatically shut off when it senses that the punch is completely through the material. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 9
Draw Stud Punch Material Being Punched 7/8" (22.2 mm) Punching mild steel with Pilot Hole 1-1/2" (ø 1.951" [49.6 mm]) to 3" (ø 3.539" [89.9 mm]) 2113B conduit sizes Draw Stud Punch Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 10
Draw Stud Punch Material Being Punched 7/8" (22.2 mm) Punching Pilot Hole stainless steel with 3/4" (ø 1.115" [28.3 mm]) to 2" (ø 2.416" [61.5 mm]) 29452 Draw Stud conduit sizes Punch Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 11
0.750" x 1.140" [19.1 mm x 29.0 mm] through 1/2" Adapter 1.250" x 1.380" [31.8 mm x 35.1 mm] rectangular 60117 3/8" Draw Stud End with Long Threads Threads with Flats 60258 1/2" Counter Nut Pilot Hole Punch Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Page 12
Pilot Hole Punch 33967 3/8" Adapter 34421 3/8" Draw Stud Punching with Electronic Connector Panel Punches End with Long Threads Threads with Flats 04638 3/8" Counter Nut Punch 7/16" (11.1mm) Pilot Hole Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
• Keep hands away from the tool head when punching. Failure to observe these warnings could result in severe injury or death. Relief valve adjustments must be done by an authorized service center. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Charge or replace battery. seconds. Tool loses oil. Damaged internal seal. Return tool to a Greenlee Authorized Service Center. Note: For Warranty Service or Repair, contact Greenlee customer service at 800-435-0786. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
Need help?
Do you have a question about the Greenlee GATOR LS50L11B and is the answer not in the manual?
Questions and answers