Related Manuals for Panduit ATLONA AT-HDVS-150-RX
Summary of Contents for Panduit ATLONA AT-HDVS-150-RX
- Page 1 HDBaseT Scaler ™ with HDMI and Analog Audio Outputs Atlona Manuals AT-HDVS-150-RX Scalers...
- Page 2 Version Information Version Release Date Notes 04/17 New format 02/18 Added firmware update procedure AT-HDVS-150-RX...
- Page 3 Welcome to Atlona! Thank you for purchasing this Atlona product. We hope you enjoy it and will take a extra few moments to register your new purchase. Registration only takes a few minutes and protects this product against theft or loss. In addition, you will receive notifications of product updates and firmware.
- Page 4 Atlona, Inc. (“Atlona”) Limited Product Warranty Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service. Under its Limited Product Warranty, Atlona, at its sole discretion, will either: •...
- Page 5 Atlona, Inc. (“Atlona”) Limited Product Warranty • Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product.
- Page 6 Important Safety Information 9. Do not defeat the safety purpose of a polarized CAUTION or grounding-type plug. A polarized plug has two RISK OF ELECTRIC SHOCK blades with one wider than the other. A grounding DO NOT OPEN type plug has two blades and a third grounding CAUTION: TO REDUCT THE RISK OF prong.
-
Page 7: Table Of Contents
Table of Contents Introduction Features Package Contents Panel Description Installation RS-232 Connector Audio Connector Power Connector Connection Instructions Connection Diagram Configuration and Management Interfaces Accessing the On-Screen Display Input Select Input Resolution Output Resolution VGA Adjust Picture Adjust Aspect Overscan Audio Others Information... -
Page 8: Introduction
Introduction The Atlona AT-HDVS-150-RX is an HDBaseT™ scaler receiver for HDMI transmission over category cable. It receives AV signals up to 1080p/60Hz or 1920×1200 video with embedded audio and control signals at distances up to 230 feet (70 meters). Features include balanced analog audio de-embedding, RS-232 control, and Power over Ethernet for compatible transmitting devices. -
Page 9: Panel Description
Panel Description HDBaseT IN DC 48V Front Rear RX TX LINK HDBaseT IN DC 48V HDMI OUT AUDIO OUT RS-232 MENU RX TX HDBaseT IN RS-232 LINK Use an Ethernet cable to connect an HDBaseT PoE Connect the included 3-pin Phoenix block from this MENU HDMI OUT AUDIO OUT... -
Page 10: Installation
Installation RS-232 Connector The AT-HDVS-150-RX provides RS-232 control between an automation system and an RS-232 device. This step is optional and is used when connecting a computer that is running the control software. Refer to Display Control (page 32) for more information. 1. -
Page 11: Power Connector
Installation Power Connector Locate the included orange Phoenix terminal block and wire the included power supply to the block, as shown below. Do not use high-torque devices, when securing the wires to the Phoenix terminal block, as this may damage the screws and/or block. -
Page 12: Connection Instructions
Installation Connection Instructions 1. Use an HDMI cable to connect an HDMI display to the HDMI OUT port on the unit. 2. Connect an Ethernet cable, up to 230 feet (70 meters), from the HDBaseT IN port on the unit to a PoE-compatible transmitter (not included). -
Page 13: Configuration And Management Interfaces
Configuration and Management Interfaces Accessing the On-Screen Display The AT-HDVS-150-RX includes a built-in On-Screen Display (OSD) menu system to manage and control all video features. DC 48V HDBaseT IN 1. Press and release the MENU button to display the OSD. Main Menu RX TX Input Select... -
Page 14: Input Select
Configuration and Management Interfaces Input Select Selects the desired input. 1. Under the Main Menu, highlight the Input Select menu item using the UP/DN buttons on the front panel. 2. Press the MENU button. 3. The Input Select menu will be displayed. 4. -
Page 15: Output Resolution 1
Configuration and Management Interfaces Output Resolution Selects the desired output resolution. The default output resolution is 720p (1280x720). The Output Resolution menu consists of three pages. 1. Under the Main Menu, highlight the Output Resolution menu item using the UP/DN buttons on the front panel. 2. -
Page 16: Picture Adjust
Configuration and Management Interfaces Setting Description Auto Adjust Automatically tunes the phase and clock of the VGA signal. Clock Polarity Sets the VGA clock polarity. • Normal - The default setting. Unless it is required, the clock polarity should be set to Normal. •... -
Page 17: Aspect
Configuration and Management Interfaces Aspect Allows the aspect ratio of the output image to be changed. 1. Under the Main Menu, highlight the Output Resolution menu item using the UP/DN buttons on the front panel. 2. Press the MENU button. 3. -
Page 18: Audio
Configuration and Management Interfaces 6. When overscan is enabled, the H Size % and V Size % fields can be adjusted. Press the UP/DN buttons to highlight the desired field. 7. Press the MENU button to select the field. 8. Press the UP/DN buttons to change the value. Press the UP button to increase the value; press the DN button to decrease the value. -
Page 19: Osd
Configuration and Management Interfaces Adjusts the appearance and position of the On-Screen Display (OSD) on the screen. 1. Under the Main Menu, highlight the Audio menu item using the UP/DN buttons on the front panel. 2. Press the MENU button. 3. -
Page 20: Others
Configuration and Management Interfaces 5. Press the MENU button to confirm the selection. 6. The current value will be highlighted in green and surrounded by brackets and two arrowheads. 7. Press the UP/DN buttons to change the value. For settings that contain a value, press the UP button to increase the value;... - Page 21 Configuration and Management Interfaces Setting Description Display HDCP Provides control over the transmission of HDCP content for the HDMI IN port on the transmitter (TX). The following options are available: • Compliant - Forces detection of HDCP-compliant sink devices. If the sink device is not HDCP-compliant, then no content will be transmitted.
-
Page 22: Information
Configuration and Management Interfaces Setting Description ProjSW Mode Used with a projector whose lamp cannot be turned on for up to 5 minutes after being shut off. Keeps control in same state as projector. Match settings with lamp delay on projector in 5 to 300 seconds. The LED will blink for the full amount of the delay time (ex. -
Page 23: System Reset
Configuration and Management Interfaces Setting Description Indicates the firmware version of both the transmitter (TX) and receiver (RX). If the TX is not connected, then “Unknown” will be listed next to the TX field. HV Total The total number of horizonal and vertical pixels. HV Display The display resolution. -
Page 24: Control Software
Configuration and Management Interfaces Control Software Connect Click this button to attempt to connect to the select COM port in the drop-down list. When successfully connected, this button will be highlighted in green. Disconnect Click this button to disconnect from the COM port. When successfully disconnected, this button will be highllighted in red. - Page 25 Configuration and Management Interfaces Output Resolution Click this button to select the output resolution on the AT-HDVS-150-RX. Output Resolutions 1024x768 720p25 1080i59.94 1080p50 1280x800 720p29.97 1080i60 1080p59.94 1280x1024 720p30 1080p23.98 1080p60 1366x768 720p50 1080p24 Native 1400x1050 720p59.94 1080p25 1600x1200 720p60 1080p29.97 1680x1050 1080i50...
- Page 26 Configuration and Management Interfaces HDVS TX Baudrate Click this drop-down list to select the required baud rate: 9600 or 115200. System Reset Click this button to reset the AT-HDVS-150-RX to factory-default settings. Read Click this button to populates all fields with the current settings of the AT-HDVS-150-RX. Display Mode Click this drop-down list to select how the DISPLAY button functions on the transmitter.
-
Page 27: Picture Controls
Configuration and Management Interfaces Audio On/Off Click this drop-down list to block the audio signal. This applies to both HDMI and analog audio. Setting Description Allows the audio signal on both HDMI and analog to pass. Blocks both HDMI and analog audio signals. HDMI Click this drop-down list to block the audio signal on the HDMI output. -
Page 28: Projector Command Settings
Configuration and Management Interfaces Projector Command Settings Load Click this button to load a saved projector settings file. The settings file is in .ini format and is created using the Save button. Save Click this button to save the current projector settings to a file. Send Click this button to send the current projector settings to the projector. -
Page 29: Projector Controls
Configuration and Management Interfaces Projector Controls Auto Display On Click this drop-down list to select when the display will be powered-on, based on the detection of a source. Setting Description Powers-on the display when a source is detected. Display is not powered-on when a signal is detected. Auto Display Off Click this drop-down list to select when the display will be powered-off, based on the detection of a source. -
Page 30: Solution Setup And Configuration Guide
Solution Setup and Configuration Guide The following sections provide step-by-step instructions for the following topics: • Input Auto-Switching • Display Control Input Auto Switching The AT-HDVS-150-TX provides auto-switching capability between HDMI IN 1 and HDMI IN 2, which will automatically switch the input to the most recently-connected or powered source when a source is disconnected. - Page 31 Solution Setup and Configuration Guide HDBaseT IN DC 48V 4. Press and release the VOL DN button until the Others menu is highlighted in blue. RX TX LINK MENU HDMI OUT AUDIO OUT RS-232 Main Menu Input Select Input Resolution Output Resolution Picture Adjust Aspect...
-
Page 32: Display Control
Solution Setup and Configuration Guide Display Control The AT-HDVS-150-RX features a control interface which can be used to program connected transmitters, allowing them to power-on/off displays as well as adjust the appearance of the output image. In order to configure display control, the control software should be downloaded and installed. The control software is available for download, under the AT-HDVS-150-RX page on the Atlona web site, and supports programming of the following transmitters. - Page 33 Solutions Setup and Configuration Guide 2. Go to the Windows Device Manager and verify the installed COM port, under Ports (COM & LPT). 3. If running Windows 10, perform the step 3a. Otherwise, continue with step 4. a. Install the gulim.ttc font file by double-clicking it. This file must be installed, if running the software under Windows 10.
-
Page 34: Programming The At-Hdvs-150-Rx
Solutions Setup and Configuration Guide Programming the AT-HDVS-150-RX Once the control software is running, it can be used to program the AT-HDVS-150-RX to affect the behavior of the connected display. For example, the display can automatically be turned on, when the source device is turned on. Conversely, when the source is turned off (or disconnected), then display is automatically turned off. -
Page 35: Projector Control
Solutions Setup and Configuration Guide Projector Control If a projector is being controlled by the AT-HDVS-150-RX, then click the Projector radio button in the top-portion of the screen, as shown below. This section of the control software is similar to the HDVS Receiver section. In addition, this area also provides two fields for RS-232 “Display On”... -
Page 36: Connecting The At-Hdvs-150-Rx To The Display
Solutions Setup and Configuration Guide 6. Once the proper command strings have been entered, refer to the tables below for information on setting the Auto Display On and Auto Display Off features. Auto Display On Click this drop-down list to select when the display will be powered-on, based on the detection of a source. Setting Description Powers-on the display when a source is detected. -
Page 37: Appendix
Appendix Default Settings The following tables list the factory-default settings for the AT-HDVS-150-RX. Feature Settings Input Select HDMI Input Resolution 1280x800 Output Res 720p60 VGA Clock Polarity Normal Picture Adjust Brightness Contrast Saturation Sharpness Aspect Full Overscan Disabled Audio Audio On / Off HDMI Audio L / R Audio Position... -
Page 38: Updating The Firmware
Appendix Updating the Firmware The following procedure is used for updating the firmware on the AT-HDVS-150-RX. Requirements • AT-HDVS-150-RX Firmware file: AT-HDVS-150-RX_[version].bin • • USB Type A to Mini-USB Type B cable • Computer with USB port 1. Download the latest firmware from the Atlona web site. 2. - Page 39 Appendix If the folder is not displayed, open Windows Explorer and locate the drive named USB UPDATER. 7. Delete all files from the USB drive, if any are present. 8. Drag-and-drop the AT-HDVS-150-RX_[version].bin firmware file to the drive. 9. After the file has been copied, disconnect the USB cable from both the computer and the AT-HDVS-150-RX. 10.
-
Page 40: Specifications
Appendix Specifications Video HD/SD 1080p@23.98/24/25/29.97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@25/29/30/50/59.94/60Hz, 576p, 576i, 480p, 480i, 1920×1200RB, 1680×1050, 1600×1200, 1600×900, 1440×900, 1400×1050, 1366×768, 1280×1024, 1280×960, 1280×800, 1280×768, 1152×854, 1024×768, 800×600, 720×400, 640×480 VESA 1080p@23.98/24/25/29.97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@25/29/30/50/59.94/60Hz, 1920×1200, 1680×1050, 1680×1200, 1400×1050, 1366×768, 1280×1024, 1280×800, 1024×768 Color Space YUV, RGB Chroma Subsampling 4:4:4, 4:2:2... - Page 41 Appendix Power Consumption 15 W (varies per paired transmitter) Supply Input: 100 - 240 V AC, 50/60 Hz Output: 48 V DC, 0.83 A Dimensions Inches Millimeters H x W x D 1.18 x 4.8 x 4.92 30 x 122 x 125 Weight Pounds Kilograms...
-
Page 42: Index
Index Saturation adjusting 16, 27 Aspect ratio Information Sharpness setting 17, 25 displaying adjusting 16, 27 Audio Info screen Source analog settings input 14, 24 connector Input Specifications enabling / disabling selecting 14, 24 Standby mode HDMI Installation setting Auto-adjust Switching VGA signal 15, 25... - Page 43 Toll free US International atlona.com 877.536.3976 41.43.508.4321 • • © 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice.