Ip to ir command converter for velocity control system (12 pages)
Summary of Contents for Panduit Atlona AT-HDVS-SC-RX
Page 1
4K / UHD Scaler for HDBaseT and HDMI ™ Atlona Manuals AT-HDVS-SC-RX Extenders...
Page 2
Version Information Version Release Date Notes 10/18 Initial release AT-HDVS-SC-RX...
Page 3
Welcome to Atlona! Thank you for purchasing this Atlona product. We hope you enjoy it and will take an extra few moments to register your new purchase. Registration only takes a few minutes and protects this product against theft or loss. In addition, you will receive notifications of product updates and firmware.
Page 4
Atlona, Inc. (“Atlona”) Limited Product Warranty Coverage Atlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service. Under its Limited Product Warranty, Atlona, at its sole discretion, will either: •...
Page 5
Atlona, Inc. (“Atlona”) Limited Product Warranty • Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product.
Page 6
Important Safety Information 9. Do not defeat the safety purpose of a polarized CAUTION or grounding-type plug. A polarized plug has two RISK OF ELECTRIC SHOCK blades with one wider than the other. A grounding DO NOT OPEN type plug has two blades and a third grounding CAUTION: TO REDUCT THE RISK OF prong.
Table of Contents Introduction Features Package Contents Panel Description Installation RS-232 Connector Analog Audio Connector Relay Connector Connection Instructions Connection Diagrams IP Configuration Using the OSD Setting the IP Address Using Commands Setting the IP Address using the Web GUI Basic Operation Managing Users Adding Users...
Introduction The Atlona AT-HDVS-SC-RX is an HDBaseT receiver and 4K/UHD scaler with a local HDMI input. It receives HDBaseT for video output up to 4K/30 4:4:4, plus embedded audio, control, and Ethernet over distances up to 330 feet (100 meters). The HDVS-SC-RX features Atlona CrystalScale technology with high-quality downscaling and upscaling, as well as advanced image optimization capabilities plus internal test patterns for setup and troubleshooting.
Panel Description 4K SCALER INPUT LINK AT-HDVS-SC-RX MENU ENTER INPUT AT-HDVS-SC-RX C1 COM C2 INPUT HDMI OUT RS-232 AUDIO OUT RELAY DC 24V 10 HDBaseT Input This LED indicator glows solid green when the unit Connect an HDBaseT transmitter, such as the AT- is powered.
Installation RS-232 Connector The AT-HDVS-SC-RX provides RS-232 control between an automation system and an RS-232 device or display control. RS-232 1 is for display control and RS-232 2 is used to control the AT-HDVS-SC-RX. This step is optional. 1. Use wire strippers to remove a portion of the cable jacket. 2.
Installation Relay Connector The AT-HDVS-SC-RX provides a RELAY port, allowing the control of screens, curtains, and other devices. Use a 48 V DC relay with no more than 1 A current draw. When the AT-HDVS-SC-RX is powered-on or rebooted, C1 and C2 are set to the Normally Open (NO) state. AT-HDVS-SC-RX...
Installation Connection Instructions 1. Connect an Ethernet cable from an HDBaseT-capable device to INPUT 1 on the rear of the unit. 2. Connect an HDMI cable from the INPUT 2 port to a UHD/HD source. 3. Connect an HDMI cable from HDMI OUT port to a UHD/HD display. 4.
INPUT HDMI OUT RS-232 AUDIO OUT RELAY DC 24V Installation IP Configuration The AT-HDVS-SC-RX is shipped with DHCP enabled. Once connected to a network, the DHCP server (if available), will automatically assign an IP address to the unit. Execute the arp -a command at the Windows command line or use an IP scanner to locate the AT-HDVS-SC-RX on the network.
Installation 7. Press the UP or DOWN cursor buttons on the front panel to toggle between Dhcp and Static. 8. Press the ENTER button to set the desired IP mode. When set to Static mode, each byte of the IP address can be set: Press the UP or DOWN cursor buttons to highlight the desired field, then press ENTER to select the field.
Installation Setting the IP Address using the Web GUI System page (page 32), in the web GUI, allows the AT-HDVS-SC-RX to use either DHCP or static IP mode. In order to access the web GUI, the IP address of the AT-HDVS-SC-RX must be known. 1.
Basic Operation Managing Users The AT-HDVS-SC-RX allows the admin user to create, edit, and remove additional TCP/IP users. All users have the same level of access to control the AT-OME-TX21-WP-E. However, only the admin user is allowed to manage other users.
Basic Operation Editing / Deleting Users The username and password of a user can be changed using this method. 1. Open the desired web browser and enter the IP address of the AT-HDVS-SC-RX. 2. Log in as the admin user with the required credentials. The factory-default username and password for the admin user are listed below: Username: root Password: Atlona...
The Web GUI Accessing the Web GUI The AT-HDVS-SC-RX includes a built-in web GUI. Atlona recommends that the web GUI be used to set up the AT-HDVS-SC-RX, as it provides intuitive management of all features. The AT-HDVS-SC-RX is shipped with DHCP enabled. Once connected to a network, the DHCP server will automatically assign an IP address to the unit.
The Web GUI Info page After logging in, the Info page is the first page to be displayed. The Info page displays information such as the model name, software, and active input, and output video resolution. Model Name The model SKU of this product. Software Version The version of firmware that the AT-HDVS-SC-RX is running.
The Web GUI Video page Prefer Timing Click this drop-down list to select the desired input resolution. Available Resolutions Native 1280x720 1440x900 1920x1200 800x600 1280x800 1600x900 2560x1440 1024x768 1366x768 1920x1080 3840x2160 HDCP Settings HDCP can be controlled on each input. Set this toggle switch to the ON position to set the HDCP reporting mode of each input (HDMI IN, HDBaseT).
Page 22
The Web GUI Input Selection Click this drop-down list to select the desired active input. In addition to selecting an input, internal video test patterns can also be selected. Inputs Input 1 HDBaseT Input 2 HDMI Internal Pattern 1 Color Bars This pattern is used to calibrate color settings on the display device.
Page 23
The Web GUI Scaler Pass-Through Click this toggle switch to the ON position to pass-through the source signal without scaling or image processing. Format Click this drop-down list to set the output resolution of the scaler. This option is not available when the Scaler Pass- Through option is set to OFF.
The Web GUI Audio page Mute Click this toggle switch to the ON position to mute all audio on the output. HDMI Audio Click this toggle switch to the OFF position to mute only the audio on the HDMI output. L/R Audio Click this toggle switch to the OFF position to mute only the audio on the AUDIO OUT port.
The Web GUI Display page Power Click the ON or OFF button to power-on or power-off the display using CEC. Volume Click the + or - button to increase or decrease the audio output volume, respectively. Click the Mute button to mute the output audio.
Page 26
The Web GUI Display Auto Power On Click this toggle switch to ENABLE to send the command to power-on the display when an A/V signal is detected. Otherwise, set to DISABLE to turn this feature off. Display Auto Power Off Click this toggle switch to ENABLE to send the command to power-off the display when an A/V signal is no longer present.
Page 27
The Web GUI Display Mode Click this drop-down list to select the behavior of the display when a source is connected. Setting Description DispSW AVon Display switches on/off, source audio/video signal is always on. DispSW AVSW Display switches on/off, source audio/video signal switches on/off. AV SW Display is always on, source audio/video signal switches on/off;...
Page 28
The Web GUI Send Mode Sets the display format for the commands in the web GUI. In Hex mode, non-valid characters are not accepted. Options: ASCII, Hex. On/Off/Volume+/Volume-/Mute • Set command Enter the command in this field. • Feedback Enter the feedback string in this field. •...
The Web GUI RS-232 page Zone When the AT-HDVS-SC-RX is connected to the AT-HDVS-SC-RX, the drop-down list boxes will be disabled and the HDBaseT baud rate will be locked at 115200. If the AT-HDVS-SC-RX is connected to another HDBaseT device, such as the AT-UHD-CLSO-824, each of these drop-down list boxes can be set to the baud rate of the HDBaseT RS-232 settings on the corresponding device.
Page 30
The Web GUI RX RS-232 Zone 1 Each of these drop-down lists refer to the setting for the RS-232 1 port on the receiver. Click the Save button to accept the settings. Setting Description Baud rate Sets the baud rate. The following options are available: 2400, 9600, 19200, 38400, 56000, 57600, 115200.
The Web GUI Config page Old Username This field cannot be changed. “admin” is the administrator user. Old Password Enter the current password for the “admin” username in this field. The default password is “Atlona”. New Username This field cannot be changed. Save Click this button to save all changes.
The Web GUI System page Control Click this radio button to select the behavior of the relays. Each relay has two states: normally open (NO) and normally closed (NC). Setting Description Follow Display The relays will toggle, based on the state of the AT-HDVS-SC-RX. For example, when the system is powered on, the relay will power-on the display.
Page 33
The Web GUI IP Mode Click this toggle switch to set the IP mode of the AT-HDVS-SC-RX. By default, the AT-HDVS-SC-RX is set to DHCP mode. Enter the IP address of the AT-HDVS-SC-RX in this field. This field will only be available if IP Mode is set to STATIC Netmask Enter the subnet mask in this field.
Appendix Updating the Firmware Updating the firmware can be completed using either the USB interface or the web GUI. Atlona recommends using the web GUI for updating the firmware. However, if a network connection is not available, the AT-HDVS-SC-RX firmware can be updated using a USB-A to USB mini-B cable. Using the Web GUI Requirements: •...
Page 35
Appendix 7. Click the OK button to begin the firmware update process. Click the Cancel button to cancel the process. During the firmware update process, the PWR LED indicator will flash, rapidly. PWR LED indicator 4K SCALER INPUT LINK AT-HDVS-SC-RX MENU ENTER INPUT...
Appendix Using USB Requirements: • AT-HDVS-SC-RX • Firmware file • Computer running Windows • USB-A to USB mini-B cable 1. Make sure the unit is powered, using the included power supply. 2. Press and hold the MENU key. While depressing the MENU button, connect the USB cable between the FW port on the AT-HDVS-SC-RX and the computer containing the firmware.
Appendix Default Settings The following tables list the factory-default settings for the AT-HDVS-SC-RX. Feature Settings A/V Settings Input Selection Input 1 Auto Switch Mode Fallback Port Previous Fallback Time 5 (seconds) HDCP Setting (Input 1) HDCP Setting (Input 2) Audio Output System Settings Display Auto Power On Disabled...
Appendix Specifications Connectors, Controls, and Indicators INPUT 1 (HDBaseT) 1 - RJ45 INPUT 2 (HDMI) 1 - Type A, 19-pin female 1 - Type mini-B, 5-pin female RS-232 1 - 5-pin captive screw AUDIO OUT 1 - 5-pin captive screw RELAY 1 - 3-pin captive screw 1 - RJ45...
Page 39
Appendix Signal Maximum TMDS Clock 300 MHz HDBaseT 10.2 Gbps HDMI HDCP 1.4 / 2.2 Temperature Fahrenheit Celsius Operating 32 to 122 0 to 50 Storage -4 to 140 -20 to 60 Humidity (RH) 20% to 90%, non-condensing Power Consumption 24.75 W Supply Input: 100 - 220 V AC, 50/60 Hz, Output: 24 V / 2.7 A DC...
Index Audio Operating notes muting Panel descriptions Bass Password adjusting default Resolution compatibility setting Configuration RS-232 See IP configuration settings Connection diagram instructions Contents Safety information package Specifications Control type Static IP setting Subnet mask Customer support Switching auto Default setttings Description Telnet front / rear panel...