Page 2
Purposes and Applications HID-2232 is intended to be used in healthcare institutions for general purpose as an assisting device for data access – patient information, medical records, media services, and so on. The product is designed for general or special use in the hospital environment.
Page 3
The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. HID-2232 Quick Reference Guide...
Page 4
Caution! Do not replace battery yourself. Please contact . The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard HID-2232 Quick Reference Guide...
Page 5
IEC 60065 for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.) Furthermore, all configurations shall comply with the system standard IEC 60601-1-1. Everybody who connects additional equipment to the signal input part or signal output part configures HID-2232 Quick Reference Guide...
Page 6
Warning! Do not modify this equipment without authorization of the manufacturer. Warning! To avoid risk of electric shock, this equipment must only be connected to a supply main with protective earth. Caution! This adapter Delta MDS-090AAS24F is a forming part of the medical device. HID-2232 Quick Reference Guide...
Page 7
HID-2232 User Manual Explanation of Graphical Symbols Warning: dangerous voltage Caution Note ISO 7000-1641: Follow operating instructions or Consult instructions for use. Direct current. Equipotential Stand-by US Conformance Follow the national requirements for disposal of equipment. HID-2232 Quick Reference Guide...
Page 8
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from the one the receiver is HID-2232 Quick Reference Guide...
Page 9
Selection of other channels is not possible. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Shielded interface cables must be used in order to comply with emission limits. HID-2232 Quick Reference Guide...
Page 10
EMI sensitive devices in its surrounding which may malfunction therefore. Environmental protection Follow national requirements to dispose of unit. Manufacturer Avalue Technology Inc. 7F, No.79, Lide St., Zhonghe District, New Taipei City, 235, Taiwan TEL: +886-2-8226-2345 FAX: +886-2-8226-2777 Web: www.avalue.com.tw Information: sales@avalue.com.tw HID-2232 Quick Reference Guide...
HID-2232 User Manual CONTENT 1. HID-2232 Multi Touch Medical Panel PC Features ........ 13 1.1 Packing List ..................13 1.2 Specifications ..................14 1.3 Front view ..................17 1.4 Rear & Bottom view ................18 1.5 System Dimensions ................19 2.
Page 12
4.6.6 Serial port 2 connector (JCOM2) ..........50 4.6.7 B2B connector (B2B1) ............51 4.6.8 USB connector 4 (JUSB4) ............52 4.6.9 Audio connector (JMIC1) ............52 4.6.9.1 Signal Description – Audio connector (JMIC1) ....52 5. General Safety Guide ................53 HID-2232 Quick Reference Guide...
HID-2232 User Manual 1. HID-2232 Multi Touch Medical Panel PC Features ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ In this chapter, you will get to know all features of our HID-2232 Multi Touch Medical Panel PC. 1.1 Packing List 1 x HID-2232 Medical Panel PC ...
4 x USB3.0 (2x Double deck) USB Port 2 x isolation USB1.1 port (by IET module, upper max. current 300mA, bottom max current 500mA) DIO Port 8 bit GPIO Video Port 1 x HDMI (by IET module) Audio Port Line out HID-2232 Quick Reference Guide...
Page 15
Sine Vibration Test Reference IEC60068-2-6 Testing procedures Test Fc : Vibration sinusoidal 1 Test Acceleration : 2G 2 Test frequency : 5~500 Hz 3 Sweep:1 Oct/ per one minute. (logarithmic) 4 Test axis : X,Y and Z axis HID-2232 Quick Reference Guide...
Page 16
0 ~ 90% Relative Humidity, Non-condensing Storage and -20 ~ 60 degree, 10%~90%@35°C, non-condensing Transportation Condition Atmospheric Pressure 50 ~ 106kPa Expected Service Life 35790hrs Other Test DIN 6868157 Note: Specifications are subject to change without notice. HID-2232 Quick Reference Guide...
LAN: for internet connection COM: for Mouse/Ethernet..etc serial port device HDMI: for display output Note! Equipotential terminal needs to be linked to the hospital ground/earth system before booting the system to protect both operator and system HID-2232 Quick Reference Guide...
HID-2232 User Manual 2. Setting Up HID-2232 Multi Touch Panel PCs ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ This chapter gives instructions on how to set up HID-2232 Multi Touch Panel PC and how to connect different cables. 2.1 VESA Mounting 2.2 Cleaning and Disinfecting HID-2232 Quick Reference Guide...
Installation instructions follow: First attach the wall-mounting to the heat-sink of the HID-2232, securing it in place with four of the M4 x 6mm screws provided. Mount the on the wall, stand or other flat surface.
Page 22
HID-2232 User Manual Suggested Screw type for mounting Note: 4 pieces of M4 x 6mm screws (P/N: E1933050611R) Warning! Use suitable mounting apparatus to avoid risk of injury. HID-2232 Quick Reference Guide...
Follow below step Connecting the Ground pin 1. With system ready, find the equipotential terminal on the rear side of the HID-2232. An equipotential terminal is provided to optionally connect to a hospital ground/earth system. 2. Prepare grounding cable and the other terminal links to the hospital ground/ earth system.
Page 24
HID-2232 User Manual The HID-2232 could only be powered by a DC power adapter (Delta MDS-090AAS24F). Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Connect the female end of the power adapter to the DC jack of the panel 2.
HID-2232 User Manual 2.3 Cleaning and Disinfecting During normal use of HID-2232, the device may become dirty and should be regularly cleaned. Cleaning Instructions 1. Turn off the computer before starting clean up. This way, you can see any dirt on the screen; the brightness of the monitor may make you miss some areas.
HID-2232 User Manual 3. Using HID-2232 Multi Touch Panel PCs ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ This chapter describes in detail all features of HID-2232 Multi Touch Panel PC. 3.1 Turn ON/OFF the System 3.2 Using LCD Display and Touch Screen HID-2232 Quick Reference Guide...
1. Press on the Power ON/OFF icon firmly for 4 seconds. 2. The Power ON/OFF LED will turns orange to indicate power is off. 3. Your system is turned OFF. Note: We recommend using operating system shut down procedure to turn the system OFF. HID-2232 Quick Reference Guide...
3. Press LED reading light icon for 4 secs to turn off the touch function (touch function always on as default) 4. Press LED reading light icon for 4 secs to turn on the touch function HID-2232 Quick Reference Guide...
And please note that brightness cannot be adjusted under DICOM mode. The brightness up/ down buttons are only functional under normal mode. Power on/off DICOM Mode HID-2232 Quick Reference Guide...
RJ-45 Ethernet 1/2 Mini-PCIe connector MPCIE1 Battery connector 2 x 1 wafer, pitch 1.25mm JBAT1 General purpose I/O connector 6 x 2 wafer, pitch 2.00mm JGPIO1 EC General purpose I/O 5 x 1 wafer, pitch 2.00mm JGPIO2 connector HID-2232 Quick Reference Guide...
Page 33
SPI connector EC Debug connector JEC1 2 x 1 header, pitch 2.00 mm SATA1 Serial ATA connector 2 x 1 wafer, pitch 2.00mm SATAPW1 SATA Power connector JDICOM_PWR2 DICOM Power connector 6 x 1 wafer, pitch 2.00mm HID-2232 Quick Reference Guide...
HID-2232 User Manual 4.4.3 Display Port power selector (JPG3) +3.3V* +12V * Default 4.4.4 AT/ATX auto power on select (JAT1) ATX* * Default HID-2232 Quick Reference Guide...
COM1-3 422RX1+ NRXDA COM1-2 485_422TX1+ NDTRA# 11 COM1-4 12 422RX1- Note: This connector is available after modify the mode of COM1 in BIOS setting. * Default 4.4.6 On-board header for USB2.0 (JUSB1) Signal +5VSB USB_z_PN10 USB_z_PP10 HID-2232 Quick Reference Guide...
HID-2232 User Manual 4.4.15 UPS-GPIO connector (JUPS1) Signal PIN PIN Signal DC_JACK_OFF# SMB_CLK SMB_DATA 4.4.16 LED connector (JLED1) Signal +5VSB LED_BOARD_EN HID-2232 Quick Reference Guide...
HID-2232 User Manual 4.4.18 SATA Power connector (SATAPW1) Signal 4.4.19 Power connector (JPWR4) Signal +VIN_12-26V +VIN_12-26V HID-2232 Quick Reference Guide...
Full speed: compatible with USB drive, Keyboard/ Mouse receiver. 4.6.2 USB connector 1/2 (JUSBD-1/2) USB Full Speed* USB Low Speed JUSBD-2 JUSBD-1 Note: Low speed: compatible with Keyboard/ mouse. *Default Full speed: compatible with USB drive, Keyboard/ Mouse receiver. HID-2232 Quick Reference Guide...
HID-2232 User Manual 4.6.5 Serial port 1 connector (JCOM1) Signal PIN PIN Signal NTXD1 NRXD1 NDCD1# NDTR1# 4.6.6 Serial port 2 connector (JCOM2) Signal PIN PIN Signal NTXD2 NRXD2 NDCD2# NDTR2# HID-2232 Quick Reference Guide...
Signal LINE_L_OUT LINE_R_OUT LINE_L_IN LINE_R_IN MIC_L MIC_R LINEIN_JD LINEOUT_JD MIC_JD 4.6.9.1 Signal Description – Audio connector (JMIC1) Signal Signal Description LINEOUT_JD AUDIO Out(ROUT/LOUT) sense pin MIC_JD MIC IN (MIC_RIN/LIN) sense pin Note: Line in function unavailable. HID-2232 Quick Reference Guide...
You want to remove/install any parts Thermal The HID-2232 is a fanless design system, heat is dispatch through rear metal heatsink which is located at VESA mount area.. When using your HID-2232 systems, it is normal for the metal heatsink to get warm. The rear metal heatsink of the HID-2232 functions as a cooling surface that transfers heat from inside the computer to the cooler air outside.
Page 54
Handle your HID-2232 with care. It is made of metal, glass, and plastic and has sensitive electronic components inside. Don't use a damaged HID-2232, such as one with a cracked screen, as it may cause injury. Setup HID-2232 on a stable work surface.