Related Manuals for Texas Instruments TPS7A10EVM-004
Summary of Contents for Texas Instruments TPS7A10EVM-004
- Page 1 TPS7A10EVM-004 Evaluation Module User's Guide Literature Number: SBVU040 February 2018...
- Page 2 SBVU040 – February 2018 TPS7A10EVM-004 Evaluation Module This user’s guide describes the operational use of the TPS7A10EVM-004 evaluation module (EVM) as a reference design for engineering demonstration and evaluation of the TPS7A10YKA low-dropout linear regulator (LDO). Setup and operating instructions, thermal and layout guidelines, a printed circuit board (PCB) layout, a schematic diagram, and a bill of materials (BOM) are included in this user's guide.
-
Page 3: Before You Begin
Introduction Texas Instruments' TPS7A10EVM-004 EVM helps design engineers evaluate the operation and performance of the TPS7A10 family of linear regulators for possible use in circuit applications. This particular EVM configuration contains a single linear regulator for handheld systems. The regulator is capable of delivering up to 300 mA to the load with ultra-low VIN to VOUT dropout voltage. -
Page 4: Evm Setup
EVM Setup www.ti.com EVM Setup This section describes how to properly connect and set up the TPS7A10EVM-004, including the jumpers and connectors on the EVM board. Input/Output Connectors and Jumper Descriptions 3.1.1 J1 – GND Bias ground return connector. 3.1.2 J2 –... -
Page 5: Soldering Guidelines
2. Short J9 (the EN pin) to IN or BIAS and float J12 to enable the output. 3. Vary the respective load and input voltage for test purposes if necessary. SBVU040 – February 2018 TPS7A10EVM-004 Evaluation Module Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... -
Page 6: Pcb Layout
Figure 1 Figure 3 show the PCB layout for this EVM. Figure 1. Assembly Layer Figure 2. Top Layer Routing Figure 3. Bottom Layer Routing TPS7A10EVM-004 Evaluation Module SBVU040 – February 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated... - Page 7 Schematic www.ti.com Schematic Figure 4 is the schematic for this EVM. SBVU040 – February 2018 TPS7A10EVM-004 Evaluation Module Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
- Page 8 Schematic www.ti.com Figure 4. TPS7A10EVM-004 Schematic TPS7A10EVM-004 Evaluation Module SBVU040 – February 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
- Page 9 Bill of Materials www.ti.com Bill of Materials Table 1 shows the BOM for this EVM. SBVU040 – February 2018 TPS7A10EVM-004 Evaluation Module Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
- Page 10 These assemblies must comply with workmanship standards according to IPC-A-610 Class 2. Unless otherwise noted in the Alternate Part Number or Alternate Manufacturer columns, all parts may be substituted with equivalents. TPS7A10EVM-004 Evaluation Module SBVU040 – February 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
- Page 11 SBVU040 – February 2018 TPS7A10EVM-004 Evaluation Module Submit Documentation Feedback...
-
Page 12: Evaluation Board/Kit Important Notice
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. - Page 13 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
- Page 14 FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 15 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 2. 実験局の免許を取得後ご使用いただく。 3. 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/ /www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 3.4 European Union 3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive): This is a class A product intended for use in environments other than domestic environments that are connected to a low-voltage power-supply network that supplies buildings used for domestic purposes.
- Page 16 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2018, Texas Instruments Incorporated...
- Page 17 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products;...
Need help?
Do you have a question about the TPS7A10EVM-004 and is the answer not in the manual?
Questions and answers