Table of Contents
Advertisement
[PROJECTOR]
[DIGITAL LINK]
5)
Press as to select [BAUDRATE].
6)
Press qw to switch the item.
f The items will switch each time you press the button.
[9600]
[19200]
[38400]
7)
Press as to select [PARITY].
8)
Press qw to switch the item.
f The items will switch each time you press the button.
[NONE]
[EVEN]
[ODD]
Note
f When [INPUT SELECT] is set to [DIGITAL LINK], communication using that serial terminal is available only when the corresponding device
(such as the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G)) is connected to the <DIGITAL LINK/
LAN> terminal.
f When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for "NO
SIGNAL SLEEP" of the DIGITAL LINK output supported device should be set to "OFF" to avoid interruption of communication.
f When [INPUT SELECT] is set to [DIGITAL LINK], communication speed for input is fixed to 9 600 bps and the parity is fixed to "NONE".
Using the control command for the existing projector
Set this function when using the control command for previously purchased Panasonic projector to control this
projector with a computer using the <SERIAL IN> terminal on the projector. The existing Panasonic projector
control software, etc., can continually be used.
1)
Press as to select [RS-232C].
2)
Press the <ENTER> button.
f The [RS-232C] screen is displayed.
3)
Press as to select [EMULATE].
4)
Press the <ENTER> button.
f The [EMULATE] screen is displayed.
5)
Press as to select an item.
[OFF]
[D3500]
[D4000]
[D/W5k SERIES]
[D/W/Z6k SERIES]
[L730 SERIES]
[L780 SERIES]
[L735 SERIES]
[L785 SERIES]
[F/W SERIES]
[LZ370]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.
Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model
No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.
Select the proper speed.
Select the parity condition.
Does not use existing control command for the projector.
D3500 series
D4000 series
D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series
DZ870 series, DW830 series, DX100 series, DZ780 series, DW750 series, DX820 series, DZ770
series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series, DW730 series,
DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, D5000 series, DZ570
series, DW530 series, DX500 series, RZ970 series, RW930 series, RX110 series, RZ770 series,
RZ660 series, RW730 series, RW620 series, RZ670 series, RW630 series, RZ575 series, RZ570
series
L730 series, L720 series, L520 series
L780 series, L750 series
L735 series
L785 series
FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series
LZ370 series
ENGLISH - 121
Advertisement
Table of Contents
