Tables - ABB HT610874 Operation Manual

Operation Manual / A130-M.. - A145-M..

Tables

Tables
Table 1: Definition of pictograms ............................... 9
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table 4: Weight of complete turbocharger unit .... 30
Table 5: Requirements for threaded rods ................ 37
Table 6: Tightening torque for standard nuts........ 39
Table 7: Torque-controlled tightening of the pres-
sure screws .................................................................... 41
Table 8: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 49
Table 9: Lubricating oil temperature at the inlet... 50
Table 10: Lubricating oil temperature at the outlet ....
50
Table 11: Tightening torque (86505) ........................ 54
Table 12: Expected replacement intervals................ 61
Table 13: Maintenance table....................................... 64
Table 14: Parameters for wet cleaning of com-
pressor ........................................................................... 67
Table 15: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 70
Table 16: Wet cleaning of turbine, parameters ....... 71
Table 17: Value table for soaking............................... 79
Table 18: Malfunctions when starting - Delayed
start-up .......................................................................... 82
Table 19: Malfunctions when starting - Vibrations 82
Table 20: Malfunctions when starting - Rubbing of
rotating parts................................................................ 82
Table 21: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 83
Table 22: Malfunctions during operation - Speed re-
duces............................................................................... 83
Table 23: Malfunctions during operation - Speed in-
creases ........................................................................... 83
Table 24: Malfunctions during operation - Exhaust
gas temperature too high .......................................... 84
Table 25: Malfunctions during operation - Charge air
pressure too low........................................................... 84
© Copyright 2022 ABB. All rights reserved.
Table 26: Malfunctions during operation - Charge air
pressure too high .......................................................... 85
Table 27: Malfunctions during operation - Engine
performance losses....................................................... 85
Table 28: Malfunction - Turbocharger surging........ 86
Table 29: Malfunction - Sporadic surge blows ........ 86
Table 30: Malfunctions when stopping - Runout
noises ............................................................................... 87
Table 31: Malfunctions when stopping - Runout time
too short.......................................................................... 87
Table 32: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 88
Table 33: Malfunction of the speed measurement
system - Measured speed too high ........................... 88
Table 34: Malfunction of the speed measurement
system - Measured speed too low............................. 88
Table 35: Swivel lifting eyes......................................... 90
Table 36: Weights of assemblies ................................ 92
Table 37: 3 press-off screws ........................................ 96
Table 38: 6 press-off screws........................................ 97
Table 39: Permissible clearances A and B ............... 105
Table 40: Nozzle ring compression PD.................... 106
Table 41: Tightening torque (51007)........................ 109
Table 42: Tightening torque (79041) ........................ 111
Table 43: Tightening torque (72011) ........................ 112
Table 44: Permissible clearances N and R ............... 113
Table 45: Tightening torque (72020) ........................ 114
Table 46: Tightening torque (51009)........................ 117
Table 47: Tightening torques ..................................... 119
Table 48: Tightening torques for insulation .......... 120
Table 49: Cover plate dimensions [mm] ................. 124
Table 50: Customer spare part set 97070 .............. 129
Table 51: Spare parts - Cartridge, oil cooled .......... 130
Table 52: Spare parts - Cartridge, water cooled..... 131
Table 53: Spare parts - Turbine casing, 1 inlet ....... 133
Table 54: Spare parts - Turbine casing, 2 inlets..... 135
HZTL4031_EN Revision P February 2022