System Design - gledhill Torrent GreenHeat OV TGH140 Design, Installation & Servicing Instructions

DESIGN
2
5
6
8
9
10
13
15
16 17 18
2
5
7
8
9
10
13
15
16 17
Typical arrangement of tappings shown on the appliance, but these can be
adjusted to suit speci c installation requirements.
The feed and expansion tank must be sized to take the water expansion of the
whole system (i.e. solid fuel boiler, open vented boiler and auxiliary heating).

SYSTEM DESIGN

Torrent GreenHeat OV
1
Basic Appliance
3 1. Open vent - 22mm comp
2. Overheat stat - 1/2" female
4
3. Plate heat exchanger ow - 22mm
4. Domestic hot water store sensor
5. Immersion heater
6. Solid fuel ow - 28mm comp
7. Hot water supply - 22mm comp
8. OV boiler ow - 22mm comp (350/450 - 28mm comp)
9. Central heating ow - 22mm comp
10. Limit stat - 1/2" female
11. Cold mains supply - 22mm comp
7
12. Cold feed - 15mm comp
13. Immersion heater
14. Plate heat exchanger return - 22mm
15. Central heating return - 22mm comp
16. OV boiler return - 22mm comp (350/450 - 28mm comp)
17. Solid fuel return - 28mm comp
11
18. Drain - 1/2" female
Component kit supplied attached
12
A. Thermostat
B. Immersion heater
14
Optional extra components
A. Header tank
B. Ball valve
C. Float
D. Overheat thermostat
E. Solid fuel tappings
F. Scale inhibitor
Torrent GreenHeat SP
1
Basic Appliance
3
1. Open vent - 22mm comp
4
2. Overheat stat - 1/2" female
3. Plate heat exchanger ow - 22mm
4. Domestic hot water store sensor
5. Solid fuel ow - 28mm comp
6. Hot water supply - 22mm comp
7. Central heating ow - 22mm comp
8. Immersion heater
9. Limit stat - 1/2" female
10. SP coil ow - 22mm comp (250/350 - 28mm comp)
6
11. Cold mains supply - 22mm comp
12. Cold feed - 15mm comp
13. SP coil return - 22mm comp (250/350 - 28mm comp)
14. Plate heat exchanger return - 22mm
15. Central heating return - 22mm comp
16. Solid fuel return - 28mm comp
11
17. Drain - 1/2" female
Component kit supplied attached
12
A. Thermostat
B. Immersion heater
14
Optional extra components
A. Header tank
B. Ball valve
C. Float
D. Overheat thermostat
E. Solid fuel tappings
F. Central heating tappings
G. Scale inhibitor
Page 10
2
7
8
10
12
13
15
16
20
21
23 24
Typical arrangement of tappings shown on the appliance, but these can be
adjusted to suit speci c installation requirements.
The feed and expansion tank must be sized to take the water expansion of the
whole system (i.e. solid fuel boiler, open vented boiler and auxiliary heating).
Please note there are 2 optional solid fuel return positions on the solar range to enable
the whole store water volume to be used to store heat when the solar contribution
is negligible.
For example, a solid fuel boiler that is used for space heating would be used in the
winter months when the solar contribution is small. Connecting it to the lower return
enables the store to hold more heat when the solar contribution is negligible.
Alternatively an Aga which runs 24 hours 365 days a year would need to be connected
to the upper return when the solar contribution is greatest and the lower when the
solar contribution is least. This allows the solar to make a contribution to the store even
though the Aga is running 24 hours a day. A manual 3-port diverter valve may be used
to switch from summer to winter mode or more sophisticated control methods used.
The controls should be tted to maximise useful energy gain: minimise loss of useful
energy and ensure that back-up heat sources are not used when adequate grade solar
contribution is available. For precise guidance please refer to "table 37 section 6.0a
System controls" of the "Domestic building compliance guide 2010".
DESIGN
Torrent GreenHeat SOL
1
Basic Appliance
3
1. Open vent - 22mm comp (450 - 28mm comp)
4 2. Overheat stat - 1/2" female
3. Plate heat exchanger ow - 22mm
4. Domestic hot water store sensor
5. Solar sensor
5 6. Solid fuel ow - 28mm comp
7. OV boiler ow - 22mm comp (350/450 - 28mm comp
6
8. Central heating ow - 22mm comp
9. Limit stat - 1/2" female
9
10. SP coil ow - 28mm comp (210 - 22mm comp)
11
11. Hot water supply - 22mm comp
12. SP coil return - 28mm comp (210 - 22mm comp)
13. Central heating return - 22mm comp
14 14. Immersion heater
15. OV boiler return - 22mm comp (350/450 - 28mm comp
17
16. Solid fuel return - 28mm comp
18
17. Cold mains supply - 22mm comp
18. Solar coil ow - 22mm comp (450 - 28mm comp)
19
19. Cold feed - 15mm comp
20. Solar sensor
22
21. Solar coil return - 22mm comp (450 - 28mm comp)
22. Plate heat exchanger return - 22mm
23. Solid fuel return 2 - 28mm comp
24. Drain - 1/2" female
Component kit supplied attached
A. Thermostat
B. Immersion heater
Optional extra components
A. Header tank
B. Ball valve
C. Float
D. Overheat thermostat
E. Solid fuel tappings
F. Sealed primary boiler coil
G. Scale inhibitor
SYSTEM DESIGN
Page 11