Table of Contents
Advertisement
Quick Links
ISSUE 5: 06-08
A sealed system central heating
and mains pressure hot water
supply appliance with thermal
store designed specifically for use
with solar energy
Design, Installation
& Servicing
Instructions Addendum
These instructions must be read in conjunction with the
standard Boilermate A-Class SP Design, installation and
servicing instructions before installation
Model Numbers
BMA 200 SP-SOL
BMA 220 SP-SOL
BMA 240 SP-SOL
BMA 260 SP-SOL
BMA 280 SP-SOL
BMA 300 SP-SOL
All models comply with the water heater manufacturers
specification for integrated thermal stores
Advertisement
Table of Contents
Related Manuals for gledhill BMA 200 SP-SOL
Summary of Contents for gledhill BMA 200 SP-SOL
- Page 1 Instructions Addendum These instructions must be read in conjunction with the standard Boilermate A-Class SP Design, installation and servicing instructions before installation Model Numbers BMA 200 SP-SOL BMA 220 SP-SOL BMA 240 SP-SOL BMA 260 SP-SOL BMA 280 SP-SOL BMA 300 SP-SOL...
- Page 2 Benchmark Logbook is still being included with all Thermal Storage products and unvented cylinders. Patents Pending Gledhill fully supports the Benchmark aims to improve the standards of installation The Gledhill Group’s first priority is to give a and commissioning of central heating systems in the UK and to encourage the regular high quality service to our customers.
- Page 3 DESIGN The arrangement of a typical BoilerMate A-Class SP Solar installation is shown schematically Solar collector below. The basic unit which is covered by these F&E cisterns Components fitted instructions incorporates the Danfoss SH - E01 within the appliance case solar controller.
- Page 4 DESIGN gulley or else issue externally at ground level. Model Selection Data Table/Weights High level termination from walls or on roofs could cause injury to people or animals below Model Reference 200 SP 220 SP 240 SP 260 SP 280 SP 300 SP if the valve were to release scalding water and steam.
- Page 5 DESIGN Appliance Dimensions *If the F&E cistern is Height Width Depth Model fitted with a ballvalve, this dimension will BMA 200-SP SOL 1330 need to increase to BMA 220-SP SOL 1330 350mm to comply with the Water Regulations. BMA 240-SP SOL 1575 F&E cistern BMA 260-SP SOL...
- Page 6 DESIGN Connection Details/Dimensions Connection Details/Dimensions - 200 model Diagrams opposite show the connection details and dimensions for the BoilerMate A-Class SP SOL appliance. The BoilerMate A-Class SP SOL units are supplied on an installation base to allow the pipe runs to connect to the appliance from any direction.
- Page 7 DESIGN Connection Details/Dimensions Connection Details/Dimensions - 240 model Diagrams opposite show the connection details and dimensions for the BoilerMate A-Class SP SOL appliance. The BoilerMate A-Class SP SOL units are supplied on an installation base to allow the pipe runs to connect to the appliance from any direction.
- Page 8 DESIGN Connection Details/Dimensions Connection Details/Dimensions - 280 model Diagrams opposite show the connection details and dimensions for the BoilerMate A-Class SP SOL appliance. The BoilerMate A-Class SP SOL units are supplied on an installation base to allow the pipe runs to connect to the appliance from any direction.
-
Page 9: Standard Equipment
Electronic scale inhibitor for mains water Note 1: All the panels, pipework and other components necessary for the installation of the remainder of the solar system can be supplied by Gledhill with the BMA SP SOL services with hardness levels above appliance. -
Page 10: Installation
DO NOT SCALE FROM THIS DRAWING. COPYRIGHT OF THIS DRAWING DATE : MARCH 2008 IS RESERVED. IT IS NOT TO BE REPRODUCED COPIED OR DISCLOSED TO A THIRD PARTY EITHER WHOLLY OR IN PART WITHOUT OUR APPROVED WRITTEN CONSENT. © GLEDHILL WATER STORAGE LTD. Page 10... -
Page 11: Front Panel
* All wire sizes 0.5mm² unless otherwise stated or pocket. TITLE JOB NAME GLEDHILL WATER STORAGE LTD. Electrical Schematic for : BOILERMATE 'A' Class SP SOL ADL1 SYCAMORE TRADING ESTATE BOILERMATE 'A' class SP SOL ADL1 SQUIRES GATE LANE... - Page 12 INSTALLATION SOLAR PANEL TYPICAL CONNECTION DIAGRAM TO BOILERMATE SP SOL Solar Panel Sensor Cable Junction Box Collector sensor T1 Internal Ceiling Roof Pitch No isolation valve should Temperature be installed between the Expansion Gauge and This component solar circuit and the safety Vessel arrangement is Check Valve...
-
Page 13: Push Button
INSTALLATION BoilerMate Heating/Hot Water Controls The current BoilerMate A-Class SP Sol incorporates separate heating/hot water and solar control systems. The BoilerMate A-Class SP Sol heating and hot water controls operate in the same way as the basic BoilerMate appliances but the single channel clock and the two rocker switches have been replaced by a two channel digital clock. - Page 14 INSTALLATION Solar Controls The solar heat circuit circulation pump is controlled by the differential temperature The BoilerMate A-Class SP Sol appliance is supplied with a Danfoss electronic Solar between the solar collector and the store Heat Regulator ref SH-EO1 built into the appliance and the necessary temperature bottom.
-
Page 15: Temperature Indicator
Pump runs, indicates high Set speed higher No alarm, temperature Pump or pump output temperature flashes Pump does not run defective For any further technical information/assistance regarding this product please ring the Gledhill Technical helpline on 08449 310000. Page 15... - Page 16 The method of filling/commissioning the solar system for leaks, including the roof connections. system is relevant to the Gledhill Solar Package • If after 30 minutes the pressure has not dropped and there are no leaks evident, and is based on the use of filling tank/pump slowly drop the pressure in the system to 1 bar.
- Page 17 INSTALLATION Stock Description Supplier/Components Models Code No. Council No. PHE pump Grundfos UPR 15-50 (modulating) GT089 Plate heat exchanger (PHE) SWEP 24 Plate heat exchanger GT017 PHE pump isolating valve - straight Vemco GT133 PHE pump isolating valve - bent Vemco GT135 CW inlet Y-line strainer...
- Page 18 INSTALLATION 4/24 6/12/13 27/28 30/31 Page 18...
- Page 19 Page 19...
- Page 20 Page 20...
- Page 21 Page 21...
- Page 22 (c) Integrated Boiler and Storage Vessel Products and Stand Alone Boilers which becomes defective within two years after the In the case of the GulfStream range of products and the Gledhill boiler range of products, Gledhill guarantees date of the delivery by us and is returned to us at the the heat exchanger (boiler) for material and construction faults for two years.
- Page 23 Gledhill will replace, free of charge, any plate heat exchanger fitted in recovering any such goods the property in which the appliance as original equipment in which scale formation occurs that materially reduces the effectiveness has remained in us under paragraph (2) above.
- Page 24 The code of practice for the installation, commissioning & servicing of central heating systems...